Wojciech Szymański

Dr. Wojciech Szymański

orcid

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
27 November 2024 in Crystals
Verified
Journal Article
Open access
PDF file
SBSonia Boczkal
Sonia Boczkal
Piotr KorczakPiotr Korczak
Piotr Korczak
KŻKonrad Żyłka
Konrad Żyłka
KLKamila Limanówka
Kamila Limanówka
BPBARTŁOMIEJ PŁONKA
BARTŁOMIEJ PŁONKA
Dariusz LeśniakDariusz Leśniak
Dariusz Leśniak
This study presents the results of research on the influence of different contents of copper in aluminium alloys based on the 6xxx series on mechanical and structural properties. The investigation started with the alloying, and casting four billet variants with different copper content—0.8% Cu; 2B—1% Cu; 3A—1.2% Cu; and 3B—1.4% Cu. The prepared materials were homogenised and extruded on a 500T horizontal press with two different process temperatures and ram speeds ranging from 1 mm/s to 9 mm/s. After heat treating to the T6 and T5 tempers, their mechanical properties were tested. On this basis, the two most promising alloys 2A and 3B were selected and subjected to further tests. After extrusion and heat treatment of the profiles (to F, T1, T2, T5, and T5510), their mechanical properties were determined to select the preferred process parameters. Finally, a structural test based on crystallographic orientation based on the EBSD technique and TEM observations allowed for the characterisation of grain size, dispersoids, and phase analysis. Bright-field (BF) analysis allowed us to compare the deformed areas for T1, T5, and T5510 temperatures. The results showed significant growth in the mechanical properties of all the subjected alloys, and the best properties were shown for a Cu content of 1.4% with a tensile strength of 460 MPa and an elongation of 16% (T5510 tempering). The structural test showed an average grain size of 18 µm to 23 µm and solid solution decomposition differences for different heat-treating parameters.

24 September 2024 in Archives of Metallurgy and Materials
Verified
Journal Article
Open access
PDF file
SBSonia Boczkal
Sonia Boczkal
MWM. Węgrzyn
M. Węgrzyn
WSW. Szymański
W. Szymański
WSWojciech Szymański
Wojciech Szymański
KWK. Wala
K. Wala
MNM. Nowak
M. Nowak
The main assumption of the conducted research was the selection of appropriate heat treatment parameters to obtain the best possible resistance to stress corrosion cracking (SCC) and the highest strength properties of the extruded profiles. The work selected the temperature and time of one- and two-stage treatment of the EN AW-7021 alloy based on aging curves. Tests carried out for samples after aging at 135°C for 24 h and two-stage aging at 90°C/8 h + 135°C/8 h revealed the highest resistance to SCC. The 7021 alloy, after heat treatment at 90°C/8 h + 135°C/16 h, reached the highest tensile strength of 534MPa. Transmission electron microscopy (TEM) observations showed slight differences in the finely dispersed nucleoids between the selected parameters of the artificial aging process.

12 June 2026 in Applied Sciences
Verified
Journal Article
Open access
PDF file
ACAneta Chołaj
Aneta Chołaj
MKMarek Koscielski
Marek Koscielski
ISIzabela Spocińska
Izabela Spocińska
WSWojciech Szymański
Wojciech Szymański
SBSonia Boczkal
Sonia Boczkal
MKMirosław Kozłowski
Mirosław Kozłowski
The increasing power density of modern electronic systems intensifies challenges related to heat dissipation and long-term reliability. Insulated metal substrates (IMS), particularly three-dimensional (3D), are increasingly used as integrated thermal–mechanical solutions in high-power electronics. However, their complex geometry and material interfaces introduce new reliability concerns, especially at solder joints. This study investigates the evolution of intermetallic compounds (IMCs) in solder joints formed on 3D aluminum IMSs with ENIG metallization, focusing on SAC305 and Sn42Bi57Ag1 solder alloys. Solder joints were subjected to environmental aging under high-temperature, high-humidity, and thermal-shock conditions to simulate realistic service environments. Microstructural and compositional analyses of the interfacial IMC layers were performed, together with measurements of IMC thickness evolution. The results show that aging significantly modifies the chemical composition and morphology of IMC layers in both solder systems. In SAC305 joints, progressive development of (Cu,Ni)6Sn5 phases with increasing Cu participation was observed. In Sn42Bi57Ag1 joints, Bi affected reaction kinetics but did not alter the diffusion-controlled nature of IMC growth. Thickness measurements indicate higher sensitivity of SAC305 joints to environment-assisted interfacial degradation, while Sn42Bi57Ag1 joints exhibit greater susceptibility to stress-assisted IMC growth during severe thermal cycling. These findings highlight the distinct reliability behaviors of tested solders on 3D IMSs and provide insight into their suitability for high-power electronic applications.

8 May 2026 in Recycling
Verified
Journal Article
Open access
PDF file
WSWojciech Szymański
Wojciech Szymański
SBSonia Boczkal
Sonia Boczkal
DKDAWIDJACEK KAPINOS
DAWIDJACEK KAPINOS
JHJoanna Hrabia-Wiśnios
Joanna Hrabia-Wiśnios
ESElżbieta Szymańska Elżbieta Szymańska
Elżbieta Szymańska Elżbieta Szymańska
MKMarek Koscielski
Marek Koscielski
Aluminum multifunctional housings can enhance circularity in electronics by replacing polymer enclosures while integrating heat sinking and electronic functions via laser direct structuring (LDS). Within the ALU4CED concept, we applied an IR-compatible LDS lacquer on aluminum, formed conductive tracks by electroless Cu/Ni/Au metallization, assembled components, and assessed end-of-life recyclability. Controlled remelting trials compared three disassembly levels: complete housings with PCBs and components, housings without PCBs, and housings with only integrated tracks. Metal yield rose from 81.4% for complete assemblies to 93.2% after PCB removal, while leaving integrated LDS tracks did not measurably penalize recovery. Only the complete electronics variant showed critical contamination (Cu = 1.64 wt.% vs. 0.25 wt.% limit for EN AC 4343); after PCB removal, composition remained close to the reference and major elements (Si, Mg, Fe) stayed within specification. Prefil testing indicated very low total inclusion content (0.006/0.001/0.002 mm2·kg−1), confirming high melt cleanliness despite coatings. Following remelting → billet casting → extrusion, tensile properties (Rm ≈ 120–123 MPa, Rp0.2 ≈ 59–61 MPa, A ≈ 29–33%) were comparable to the reference profile. These results demonstrate the technological feasibility of closed-loop recycling for LDS functionalized aluminum housings and inform clear Design-for-Recycling guidance: design for rapid PCB removal, allow LDS layers to remain during melting, and maintain compatibility with the 4343 family to enable efficient internal recycling.