Adilson Campos Paula Junior

Dr. Adilson Campos Paula Junior

University of Minho, Guimarães, Braga, Portugal
orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 June 2020 in Energies
Verified
Journal Article
Open access
PDF file
Elisabete TeixeiraElisabete Teixeira
Elisabete Teixeira
GMGilberto Machado
Gilberto Machado
Adilson Campos Paula JuniorAdilson Campos Paula Junior
Adilson Campos Paula Junior
CGChristiane Guarnier
Christiane Guarnier
Jorge FernandesJorge Fernandes
Jorge Fernandes
Ricardo MateusRicardo Mateus
Ricardo Mateus
The present research is focused on an experimental investigation to evaluate the mechanical, durability, and thermal performance of compressed earth blocks (CEBs) produced in Portugal. CEBs were analysed in terms of electrical resistivity, ultrasonic pulse velocity, compressive strength, total water absorption, water absorption by capillarity, accelerated erosion test, and thermal transmittance evaluated in a guarded hotbox setup apparatus. Overall, the results showed that compressed earth blocks presented good mechanical and durability properties. Still, they had some issues in terms of porosity due to the particle size distribution of soil used for their production. The compressive strength value obtained was 9 MPa, which is considerably higher than the minimum requirements for compressed earth blocks. Moreover, they presented a heat transfer coefficient of 2.66 W/(m2·K). This heat transfer coefficient means that this type of masonry unit cannot be used in the building envelope without an additional thermal insulation layer but shows that they are suitable to be used in partition walls. Although CEBs have promising characteristics when compared to conventional bricks, results also showed that their proprieties could even be improved if optimisation of the soil mixture is implemented.

20 February 2021 in Crystals
Verified
Journal Article
Open access
PDF file
Adilson Campos Paula JuniorAdilson Campos Paula Junior
Adilson Campos Paula Junior
CJCláudia Jacinto
Cláudia Jacinto
TOThaís M. Oliveira
Thaís M. Oliveira
APAntonio E. Polisseni
Antonio E. Polisseni
FBFabio M. Brum
Fabio M. Brum
Ricardo MateusRicardo Mateus
Ricardo Mateus
The search for environmental preservation and conservation of natural resources gives rise to new concepts and viable technical solutions on the path to sustainable development. In this context, this study’s main objective is to analyse the influence of recycled concrete aggregates (RCAs) on the development of pervious concrete, whose use as a floor covering represents an excellent device to mitigate the urban soil sealing phenomena. For this, mechanical and hydraulic tests were carried out, in addition to microstructural analyses and the assessment of its environmental performance. The results obtained were compared to reference studies also involving the incorporation of recycled aggregates. A pilot-scale case study was conducted, involving a parking space lined with pervious concrete moulded “in situ”. In laboratory tests, permeability coefficients and mechanical strengths compatible with the literature and above the normative limit for light traffic were found. The case study demonstrated higher permeability than in the laboratory, but the flexural strength was lower, being indicated only for pedestrian traffic. The environmental assessment showed that the RCA represents a positive contribution to the environmental performance of pervious concrete. Still, attention should be given to the recycled aggregate transport distance between the concrete plant and the RCA treatment plant.

11 May 2023 in Polymers
Verified
Journal Article
Open access
PDF file
Lucas Matheus Caldas Vicente LopesLucas Matheus Caldas Vicente Lopes
Lucas Matheus Caldas Vicente Lopes
DRDaniel Reis
Daniel Reis
Adilson Campos Paula JuniorAdilson Campos Paula Junior
Adilson Campos Paula Junior
Manuela AlmeidaManuela Almeida
Manuela Almeida
This study aims to evaluate the thermal and mechanical performances of PET-G thermoplastics with different 3D microstructure patterns and infill densities. The production costs were also estimated to identify the most cost-effective solution. A total of 12 infill patterns were analysed, including Gyroid, Grid, Hilbert curve, Line, Rectilinear, Stars, Triangles, 3D Honeycomb, Honeycomb, Concentric, Cubic, and Octagram spiral with a fixed infill density of 25%. Different infill densities ranging from 5% to 20% were also tested to determine the best geometries. Thermal tests were conducted in a hotbox test chamber and mechanical properties were evaluated using a series of three-point bending tests. The study used printing parameters to meet the construction sector’s specific needs, including a larger nozzle diameter and printing speed. The internal microstructures led to variations of up to 70% in thermal performance and up to 300% in mechanical performance. For each geometry, the mechanical and thermal performance was highly correlated with the infill pattern, where higher infill improved thermal and mechanical performances. The economic performance showed that, in most cases, except for the Honeycomb and 3D Honeycomb, there were no significant cost differences between infill geometries. These findings can provide valuable insights for selecting the optimal 3D printing parameters in the construction industry.

22 February 2024 in Applied Sciences
Verified
Journal Article
Open access
PDF file
CTChiara Turco
Chiara Turco
Adilson Campos Paula JuniorAdilson Campos Paula Junior
Adilson Campos Paula Junior
CJCláudia Jacinto
Cláudia Jacinto
Jorge FernandesJorge Fernandes
Jorge Fernandes
Elisabete TeixeiraElisabete Teixeira
Elisabete Teixeira
Ricardo MateusRicardo Mateus
Ricardo Mateus
In the context of sustainable building development, Compressed Earth Blocks (CEBs) have garnered increasing attention in recent years owing to their minimal environmental and economic impact. However, owing to the inherent diversity of raw soil and the production process’s reliance on expertise, the properties of these blocks are subjected to multifaceted influences. Among these, the significance of soil particle size variation often remains overlooked, leaving its impact ambiguous. This study endeavours to address this gap in existing research by delving into this aspect. Two distinct batches of CEBs were produced by adjusting the grain size curve of a single type of sieved soil with different maximum mesh openings: 2 mm for R1 CEBs and 12.5 mm for R2 CEBs. Experimental results reveal significant differences in thermophysical characteristics: on average, R1 blocks show superior thermal performance, boasting a 23% reduction in thermal conductivity compared to R2 blocks, and are lighter, with an 8% decrease in dry bulk density. Although no significant changes in mechanical parameters were observed, finer-structured R1 blocks showed a 25% greater tendency to absorb water due to changes in their porous structure. This study sheds light on the sensitivity of thermal parameters to changes in soil particle size and shows that blocks with finer particles exhibit poorer heat conduction and heat diffusion. Besides providing new insights into the literature, this research also provides a strategic approach to optimise the thermophysical properties of CEBs. By understanding the influence of particle size, researchers and practitioners can now develop strategies to enhance these properties and improve the overall performance of CEBs.

7 June 2024 in Journal of Environmental Management
Verified
Journal Article
Open access
DADiana I. Alves
Diana I. Alves
ÓCÓscar Samuel Novais Carvalho
Óscar Samuel Novais Carvalho
Nuno A. T. C. FernandesNuno A. T. C. Fernandes
Nuno A. T. C. Fernandes
LCLivia Tavares Cosentino
Livia Tavares Cosentino
Adilson Campos Paula JuniorAdilson Campos Paula Junior
Adilson Campos Paula Junior
DFDiana Ferreira
Diana Ferreira
The footwear industry significantly impacts the environment, from raw material extraction to waste disposal. Transforming waste into new products is a viable option to mitigate the environmental consequences, reducing the reliance on virgin raw materials. This work aims to develop thermal and acoustic insulation materials using polyester waste from footwear industry. Two nonwoven and two compressed nonwoven structures, comprising 80% polyester waste and 20% commercial recycled polyester (matrix), were produced. The materials were created through needle-punching and compression molding techniques. The study included the production of sandwich and monolayer nonwoven structures, which were evaluated considering area weight, thickness, air permeability, mechanical properties, morphology using field emission scanning electron microscopy, and thermal and acoustic properties. The nonwoven samples presented high tensile strength (893 kPa and 629 kPa) and the highest strain (79.7% and 73.3%) and compressed nonwoven structures showed higher tensile strength (2700 kPa and 1291 kPa) but reduced strain (25.8% and 40.8%). Nonwoven samples showed thermal conductivity of 0.041 W/K.m and 0.037 W/K.m. Compressed nonwoven samples had higher values at 0.060 W/K.m and 0.070 W/K.m. While the sample with the highest conductivity exceeds typical insulation levels, other samples are suitable for thermal insulation. Nonwoven structures exhibited good absorption coefficients (0.640-0.644), suitable for acoustic insulation. Compressed nonwoven structures had lower values (0.291-0.536), unsuitable for this purpose. In summary, this study underscores the potential of 100% recycled polyester structures derived from footwear and textile industry waste, showcasing remarkable acoustic and thermal insulation properties ideal for the construction sector.

15 October 2026
Verified
Book Chapter
Open access
PDF file
Adilson Campos Paula JuniorAdilson Campos Paula Junior
Adilson Campos Paula Junior
CJCláudia Jacinto
Cláudia Jacinto
Elisabete TeixeiraElisabete Teixeira
Elisabete Teixeira
RMRicardo Mateus
Ricardo Mateus
The environmental performance of masonry systems strongly influences the overall environmental impact of buildings. This study presents a comparative environmental assessment of wall systems built with compressed earth blocks (CEBs) incorporating industrial waste and by-products, alongside conventional masonry solutions. The analysis is based on life cycle assessment (LCA) using life cycle inventory data obtained from a Portuguese producer. The CEB solutions correspond to previously optimised formulations. These include blocks incorporating cork granules and waste tyre textile fibres (WTTF), as well as two types of construction and demolition waste (CDW): railway concrete and ceramic tile waste. The earthen solutions are compared with conventional masonry systems, namely fired ceramic bricks and concrete blocks. The functional unit adopted is 1 m2 of interior partition wall. The assessment follows a cradle-to-gate perspective (modules A1–A3 of EN 15804:2012 + A2). It includes raw material supply, transport and block production. Environmental impacts were quantified through eight indicators, primarily the Global Warming Potential (GWP). Results show that all CEB wall solutions present lower environmental impacts than conventional masonry systems across all indicators. The GWP of the optimised CEB walls ranges from 16.9 to 21.5 kg CO2 eq/m2. This corresponds to reductions of 38–51% compared with ceramic hollow brick (34.4 kg CO2 eq/m2) and 31–46% compared with concrete block (31.1 kg CO2 eq/m2). The best-performing formulations – CG5 (cork granules) and CT15 (ceramic tile waste) – achieve the lowest GWP, without environmental trade-offs. These results support the positioning of waste-based earthen products in the construction market and the development of Environmental Product Declarations for CEB wall systems.