26 February 2024 in IEEE Journal of Emerging and Selected Topics in Power Electronics
Inertia plays a vital role in maintaining the frequency stability of the power system. Insufficient inertia will deteriorate the lowest point of frequency and damage the stability and reliability of the power system. The Andronov-Hopf oscillator (AHO) control is a grid-forming control based on instantaneous current feedback, which has superior self-synchronization, accurate power sharing and low harmonics. However, the similar nonlinear droop characteristic embedded in the dynamic response of AHO cannot provide inertia to the power system. In this paper, a modified AHO embedded with virtual inertial control is proposed, which provides virtual inertia for the frequency response by adding the quasi-resonant controller to the current input loop of AHO. With well-designed structure and parameters of the virtual inertial controller, the modified AHO controller can effectively provide suitable inertia and damping ratio for the power system. The experimental results show that compared with the traditional AHO control, the modified AHO control provides enough inertia to alleviate the rate of change of frequency of the power system in the island mode, while having low power overshoot in the grid-connected mode.
23 May 2024 in IEEE Transactions on Power Electronics
Grid forming control has been widely applied in the fields of renewable energy systems, owing to its capability to generate self-synchronous voltage and exhibit superior small-signal stability under weak grid. Andronov-Hopf oscillator (AHO) control is an emerging nonlinear controller to implement grid-forming control, while its transient behaviors under large-signal disturbances have not been fully explored. Different from the droop control with fixed droop coefficients, the transient stability of AHO-based converter under large grid disturbances will be deteriorated due to the equivalent nonlinear droop coefficients of AHO control. Therefore, this article proposes a transient stability enhanced Andronov-Hopf oscillator (EAHO) control. By reconstructing the dynamic equations of traditional AHO control, the monotonically decreasing nonlinear droop coefficients of traditional AHO control are reshaped into monotonically increasing as the voltage amplitude increases. The transient stability features of the droop, AHO, and EAHO control during grid voltage sags are compared and summarized. The theoretical analysis and experiment results show that the transient stability of EAHO control is significantly improved compared to AHO control.
9 May 2025 in IEEE Transactions on Power Electronics
Oscillator-based grid-forming (GFM) control, such as dispatchable virtual oscillator and Andronov–Hopf oscillator control, offers a rigorous analytical framework with enhanced synchronization, lower harmonic, and faster dynamic response but lacks effective inertia support. Insufficient inertia will impair the stability and reliability of the power system, especially in the system with parallel inverters. To fundamentally solve the issue of insufficient inertia in traditional oscillator-based GFM control, a Duffing–Hopf oscillator control is proposed. The second-order Duffing–Hopf oscillator control ensures inertia and damping properties within the active power control loop. Furthermore, a q-axis component of the point of common coupling (PCC) voltage feedforward damping control is proposed to suppress active power oscillation during load fluctuations in the parallel system. The feedforward component provides extra damping power by indirectly incorporating the grid frequency into the active power control loop without relying on a phase-locked loop. The experimental results show that compared with the traditional oscillator-based GFM control, the Duffing–Hopf oscillator control provides enough inertia and damping ratio to alleviate the rate of change of frequency, and the q-axis component of PCC voltage feedforward control can effectively suppress the power oscillations caused by inconsistent control parameters.
19 September 2024 in IEEE Transactions on Power Electronics
The medium-voltage medium-frequency transformer is a critical component of high-power dc converters. However, the ultrafast switching speed of wide bandgap semiconductors can induce voltage oscillations in the medium-frequency transformer, increasing the risk of primary-insulation partial discharge and leading to permanent breakdown. Existing research has focused on voltage oscillations occurring at ports, but there is insufficient knowledge about those happening within the winding. This article presents a model for calculating internal voltage oscillations. Compared to conventional models, it is simple and considers the core electrical energy for the first time. Accordingly, the physically-based analytical formulas are derived to calculate voltage oscillations. Based on the model, the relationship between voltage oscillations, port voltage, and transformer structure is analyzed. The oscillation mitigation method is presented and validated by experiment.
15 February 2023 in IEEE Journal of Emerging and Selected Topics in Industrial Electronics
Current harmonic is an important factor in power converters' DC-link design. Its accurate derivation is conducive to estimating the reliability of DC-link capacitors. In active power filter (APF), due to its wide output bandwidth, the DC link suffers current harmonics on a broader spectrum, and the coupling effects among compensated harmonics make the derivation in this application more complex. However, the traditional methods in voltage source inverters (VSIs) usually assume the output current to be a simple sinusoid, or only calculate the root mean square (RMS) values. They cannot readily illustrate the coupling effect, nor discriminate between different modulation strategies. This paper presents a general method for APF to solve the DC-link current harmonics under any operation condition. Using Double-Fourier theory, a new variable called ‘harmonic factor’ is defined to describe the coupling effect among compensated harmonics. Then the DC-link current spectrum is quantitatively derived with the low-frequency compensated harmonics and the switching-frequency ripple currents. Finally, the simulation and experiment of a 2-level 100-A APF verify the theoretical analysis.
24 July 2025 in IEEE Transactions on Industrial Electronics
The sinusoidal alternating current (ac) synchronous generator-based power system has served as the backbone of electricity generation and distribution for over a century. However, to align with the evolving landscape of renewable energy sources and the power electronics-dominated high-voltage direct current (HVDC) transmission, this article innovatively proposes a fully step-wave ac collection system. This system aims to mitigate the losses inherent in electricity transmission and power conversion of renewable energy sources. The sending-end converter operates at a fundamental switching frequency of 50 or 60 Hz, significantly reducing switching losses. Furthermore, compared to sinusoidal systems, the proposed step-wave approach achieves a 15.5% improvement in dc voltage utilization for converters, leading to an estimated 25% reduction in conduction-type losses, while maintaining the same peak voltage stress across the entire system. We experimentally demonstrated the viability of utilizing a step-wave ac voltage and current framework. The step-wave system exhibited a remarkable 34.7% reduction in power losses compared to its sinusoidal counterpart. This innovative approach offers a potential solution for enhancing the efficiency and adaptability of modern power systems, tailored to the demands of power electronics-dominated grids.