Gallium oxide (Ga2O3) has attracted great attention for electronic device applications due to its ultra-wide bandgap, high breakdown electric field, and large-area affordable substrates grown from the melt. However, its thermal conductivity is significantly lower than that of other wide bandgap semiconductors such as SiC, AlN, and GaN, which will impact its ability to be used in high power density applications. Thermal management in Ga2O3 electronics will be the key for device reliability, especially for high power and high frequency devices. Similar to the method of cooling GaN-based high electron mobility transistors by integrating it with high thermal conductivity diamond substrates, this work studies the possibility of heterogeneous integration of Ga2O3 with diamond for the thermal management of Ga2O3 devices. In this work, Ga2O3 was deposited onto single crystal diamond substrates by atomic layer deposition (ALD), and the thermal properties of ALD-Ga2O3 thin films and Ga2O3–diamond interfaces with different interface pretreatments were measured by Time-domain Thermoreflectance. We observed a very low thermal conductivity of these Ga2O3 thin films (about 1.5 W/m K) due to the extensive phonon grain boundary scattering resulting from the nanocrystalline nature of the Ga2O3 film. However, the measured thermal boundary conductance (TBC) of the Ga2O3–diamond interfaces is about ten times larger than that of the van der Waals bonded Ga2O3–diamond interfaces, which indicates the significant impact of interface bonding on TBC. Furthermore, the TBC of the Ga-rich and O-rich Ga2O3–diamond interfaces is about 20% smaller than that of the clean interface, indicating that interface chemistry affects the interfacial thermal transport. Overall, this study shows that a high TBC can be obtained from strong interfacial bonds across Ga2O3–diamond interfaces, providing a promising route to improving the heat dissipation from Ga2O3 devices with lateral architectures.
Record DC power has been demonstrated in AlGaN/GaN high electron mobility transistors fabricated using a substrate replacement process in which a thick diamond substrate is grown by chemical vapor deposition following removal of the original Si substrate. Crucial to the process is a ~30 nm thick SiN interlayer that has been optimized for thermal resistance. The reductions obtained in self-heating have been quantified by transient thermoreflectance imaging and interpreted using 3D numerical simulation. With a DC power dissipation level of 56 W/mm, the measured average and maximum temperatures in the gate-drain access region were 176 °C, and 205 °C, respectively.
Ion implantation-induced effects were studied in Ge implanted β-Ga2O3 with the fluence and energy of 3 × 1013 cm−2/60 keV, 5 × 1013 cm−2/100 keV, and 7 × 1013 cm−2/200 keV using analytical electron microscopy via scanning/transmission electron microscopy, electron energy loss spectroscopy, and precession electron diffraction via TopSpin. Imaging shows an isolated band of damage after Ge implantation, which extends ∼130 nm from the sample surface and corresponds to the projected range of the ions. Electron diffraction demonstrates that the entirety of the damage band is the κ phase, indicating an implantation-induced phase transition from β to κ-Ga2O3. Post-implantation annealing at 1150 °C for 60 s under the O2 atmosphere led to a back transformation of κ to β; however, an ∼17 nm damage zone remained at the sample surface. Despite the back transformation from κ to β with annealing, O K-edge spectra show changes in the fine structure between the pristine, implanted, and implanted-annealed samples, and topspin strain analysis shows a change in strain between the two samples. These data indicate differences in the electronic/chemical structure, where the change of the oxygen environment extended beyond the implantation zone (∼130 nm) due to the diffusion of Ge into the bulk material, which, in turn, causes a tensile strain of 0.5%. This work provides a foundation for understanding of the effects of ion implantation on defect/phase evolution in β-Ga2O3 and the related recovery mechanism, opening a window toward building a reliable device for targeted applications.
20 October 2020 in IEEE Transactions on Electron Devices
Gallium nitride (GaN) high electron-mobility transistors (HEMTs) offer considerable high-power operation but suffer in reliability due to potentially damaging self-heating. In this study, self-heating in AlGaN/GaN HEMTs on high conductivity substrates is assessed using a high-resolution thermoreflectance (TR) imaging technique, to compare the thermal response between GaN-on-Si, GaN-on-Diamond, and GaN-on-4H-SiC. The TR method accuracy at high-power density is verified using a nonlinear coefficient of TR (CTR) as a function of temperature. The acquired steady-state thermal maps give a thermal resistance of 11.5 mm · K/W for GaN-on-Si (based on peak channel temperature), compared to 2.7 and 3.3 mm · K/W for GaN-on-SiC and GaN-on-diamond substrates, respectively. The tested GaN-on-diamond HEMT exhibits similar heating rates to those seen on a SiC substrate, with a slightly higher peak temperature, which indicates a higher thermal boundary resistance that could offset the benefits of using a higher conductivity substrate and lead to faster thermally enhanced degradation. The analysis reveals the importance using high-resolution imaging to detect hotspots and areas of peak temperature that largely affect failure initiation and device reliability and which may not be otherwise observable.
17 December 2015 in IEEE Transactions on Nuclear Science
Single-event transients (SETs) were investigated in Al 0.3 Ga 0.7 N/GaN high-electron-mobility transistors (HEMTs) using optical excitation via two-photon absorption and by heavy ions. The amplitudes and widths of the SETs were found to depend on a number of different factors, including bias conditions, strike location, and material quality.
Plasma etching of p-type GaN creates n-type nitrogen vacancy (VN) defects at the etched surface, which can be detrimental to device performance. In mesa isolated diodes, etch damage on the sidewalls degrades the ideality factor and leakage current. A treatment was developed to recover both the ideality factor and leakage current, which uses UV/O3 treatment to oxidize the damaged layers followed by HF etching to remove them. The temperature dependent I–V measurement shows that the reverse leakage transport mechanism is dominated by Poole–Frenkel emission at room temperature through the etch-induced VN defect. Depth resolved cathodoluminescence confirms that the damage is limited to first several nanometers and is consistent with the VN defect.