25 April 2022 in Journal of the Brazilian Society of Mechanical Sciences and Engineering
1 August 2025 in Physics of Fluids
To investigate the impact of internal pressure fluctuations on the performance of multiphase flow mechanical seals in high-speed rotating equipment, this study focuses on a spiral groove mechanical seal and establishes a transient continuous boiling model that comprehensively considers centrifugal inertia and phase transition. The transient Reynolds equation, energy equation, and heat transfer equation are solved using the finite difference method, and the small perturbation method is employed to analyze multi-variable perturbations of film pressure, viscosity, and density. The study examines the influence of pressure fluctuations at the inner and outer diameters on the phase state of the fluid film and the steady-state and dynamic performance of the seal when the fluid film is in different phase states. The results indicate that the location of pressure fluctuations significantly affects the phase transition ratio of the fluid film and the sealing performance. Compared to inner diameter pressure fluctuations, outer diameter pressure fluctuations exhibit a more pronounced effect on the response curves of fluid film phase transition ratio, opening force, and axial stiffness coefficient, while showing a weaker influence on leakage rate and axial damping coefficient. When outer diameter pressure fluctuations stabilize, the restored stable response times of sealing performance and dynamic characteristic coefficients are significantly longer than those for inner diameter pressure fluctuations. Large-scale and rapid changes in the vapor mass fraction of the fluid film can significantly alter the pressure distribution, causing strong oscillations in the response curves of sealing performance and dynamic characteristic coefficients, and transient increases in leakage rate.
1 November 2025 in Physics of Fluids
To meet the requirements of high-speed and high-power rotational equipment for gas thrust bearings with large load bearing capacity and high stiffness, this study takes the spiral groove–orifice restrictor coupled hybrid aerostatic–aerodynamic thrust bearing (HATB) as the research object. Using computational fluid dynamics numerical simulation and performance experiments, this study investigates the influence of the relative position between the spiral groove and the orifice restrictor on gas flow characteristics, load bearing capacity, and stiffness of the HATB. Furthermore, the effects of gas supply pressure and rotational speed on the coupling interaction between the spiral groove and the orifice restrictor are analyzed. The results reveal that the orifice restrictor dominates the gas pressure distribution within the gas film of the bearing, while the spiral groove alters the gas pressure distribution at its location and adjusts the gas pressure distribution in adjacent regions. The coupling interaction between the spiral groove and the orifice restrictor exhibits significant dependence on the rotational speed of the thrust surface. Under stationary conditions or low rotational speeds, close proximity between the spiral groove and the orifice restrictor results in synergistic static performance enhancement. As the spacing increases, the coupling effect between the spiral groove and the orifice restrictor shifts from synergistically enhancing bearing performance to synergistically suppressing it. When the rotational speed exceeds a certain critical value, spiral groove and orifice restrictor could synergistically enhance the load bearing capacity and stiffness of gas bearing. Experimental findings demonstrate that under stationary conditions and large gas film thickness, the experiment load bearing capacity and experiment stiffness of HATB A1, HATB A2, and HATB A3 surpass those of orifice-throttled aerostatic thrust bearing. This study highlights that an optimized design of the relative position between the spiral groove and the orifice restrictor can improve both the load bearing capacity and stiffness of the HATB, offering valuable insight for the design of high-performance gas thrust bearings in precision applications.
1 October 2025 in Physics of Fluids
This article proposes micro pneumatic turbines with shift inlet and outlet. The rotation speeds and output powers of the micro pneumatic turbines with four inlet and outlet layouts [radial inlet and radial outlet (RIRO); inlet and outlet both circumferential shift (IOBS); radial inlet and axial outlet (RIAO); inlet circumferential shift and axial outlet (ISAO)] are calculated by using actual conditions driving simulation. Moreover, the influence of inlet and outlet layout on turbine performance is analyzed according to flow characteristics and the Ω-vortex identification criterion. Furthermore, the maximum rotation speed and corresponding structure parameters and output power of the micro pneumatic turbine with the optimal inlet and outlet layout are obtained by using quadratic regression equations. Finally, the effects of inlet and outlet angles on the performance of the turbine with the optimal inlet and outlet layout are studied. The results indicate that the turbine with an IOBS layout can effectively alleviate abrupt pressure changes near the blade, reducing the occurrence of vortices and flow separation, and exhibiting the best performance. The maximum rotation speed of the IOBS turbine reaches to 356.43 krpm, and the corresponding output power is 253.68 W when the turbine diameter, blade height and tip clearance are 12.5, 2.6, and 1 mm, respectively. The influence of inlet angle on IOBS turbine performance is significant, whereas that of outlet angle is small.
19 June 2023 in Journal of the Brazilian Society of Mechanical Sciences and Engineering