1 December 2020 in IEEE Transactions on Components, Packaging and Manufacturing Technology
Increasing data rates, spectrum efficiency and energy efficiency have been driving major advances in the design and hardware integration of RF communication networks. In order to meet the data rate and efficiency metrics, 5G networks have emerged as a follow-on to 4G, and projected to have 100X higher wireless date rates and 100X lower latency than those with current 4G networks. Major challenges arise in the packaging of radio-frequency front-end modules because of the stringent low signal-loss requirements in the millimeter-wave frequency bands, and precision-impedance designs with smaller footprints and thickness. Heterogeneous integration in 3D ultra-thin packages with higher component densities and performance than with the existing 2D packages is needed to realize such 5G systems. This paper reviews the key building blocks of 5G systems and the underlying advances in packaging technologies to realize them.
5 November 2018 in IEEE Microwave and Wireless Components Letters
Package-integrated and ultra-thin low-pass filter (LPF) and bandpass filter (BPF) with footprint smaller than 0.5λ₀x0.5λ₀x0.025λ₀ at the operating frequencies of 28- and 39-GHz bands are presented for 5G and mm-wave small-cell application. Such package integration of 5G filters with ultrashort 3-D interconnects allows for low interconnect losses that are similar to that of on-chip filters, but low component insertion loss of off-chip discrete filters. These thin-film filters exhibit a cross-sectional height of 188.5 μm and can be utilized either as embedded components or integrated passive devices in module packages. Three topologies of LPF and BPF in total are modeled, designed, and fabricated on precision thin-film buildup layers on glass substrate as a core. Large-area panel-compatible semiadditive patterning (SAP) process is utilized to form high-precision topologies to aid the low-cost fabrication of ultraminiaturized filters. SAP also enables the realization of ultra-thin traces to precisely model high-impedance inductive lines compared to conventional subtractive etching and printing techniques. This results in filters with low insertion loss, low VSWR, and high selectivity. The simulated and measured results of filters show an excellent correlation.
21 September 2020 in IEEE Transactions on Microwave Theory and Techniques
This article presents the design and demonstration of a high-bandwidth antenna-in-package (AiP) module focusing on low-loss interconnects and Yagi-Uda antenna performance fabricated on a 100-μm low coefficient-of-thermal-expansion (CTE) glass for the 28-GHz band. It shows the modeling, design, and characterization of key technology building blocks along with the process development of advanced 3-D glass packages. The building blocks include impedance-matched antenna-to-die signal transitions, Yagi-Uda antenna, and 3-D active-passive integration with backside die assembly on 100-μm glass substrates. The design and stack-up optimization of antenna-integrated millimeter-wave (mm-wave) modules is discussed. Process development to achieve high-density interconnects and precise dimensional control in multilayered thin glass-based packages is also described. The characterization results of the key technology building blocks show an insertion loss of 0.021 dB per through-package via (TPV), leading to the whole-chain loss of less than 1 dB and a return loss lower than 20 dB. The fabricated Yagi-Uda antenna features high repeatability of wide bandwidth due to the process control enabled by glass substrates. The antenna measurements show a bandwidth of 28.2%, which covers the entire 28-GHz fifth-generation (5G) frequency bands (n257, n258, and n261). The flip-chip assembled low-noise amplifier with 80-μm solder balls shows a maximum gain of 20 dB as desired. The performance of the glass-based package integrated antennas is benchmarked to other 5G substrate technologies, such as organic laminates or co-fired ceramic-based substrates.
23 February 2021 in IEEE Transactions on Components, Packaging and Manufacturing Technology
Glass-based packaging presents unique opportunities for supporting 5G and beyond frequencies. In this work, we present the first broadband characterization results for the electrical properties of Ajinomoto build-up film (ABF) laminated on glass substrates. ABF/glass/ABF-based stack up has been characterized from 20 to 170 GHz. We also report the low-loss performance of ABF/glass/ABF transmission lines. The material stack up consists of a 100- μm-thick EN-A1 glass core from Asahi Glass Company (AGC) with 15- μm ABF GL102 laminated on both sides. Semiadditive process (SAP) has been used to metalize the stack up. A microstrip ring resonator (MRR) method has been used to extract the dielectric constant and loss tangent of the stack up. The dispersive model estimates the dielectric constant of the stack up to be ~4.72 for the entire frequency range with a variance of +0.1. The measured loss tangent values were 0.004, 0.009, and 0.012 at 23, 103, and 140 GHz, respectively. The electrical characterization results with a confidence interval of 95% have been reported. The average insertion loss for coplanar waveguide (CPW) lines in the frequency range was measured to be between 0.055 and 0.50 dB/mm. The average insertion loss for microstrip in the same frequency range was measured to be 0.12-0.62 dB/mm. Along with the good model to hardware correlation, the performance of the transmission lines has been compared with the insertion loss published for other substrate technologies.
19 August 2020 in IEEE Antennas and Wireless Propagation Letters
A broadband and miniaturized planar Yagi AiP design for the fifth-generation (5G) wireless communication is proposed. The monopole taper radiator is adopted for the proposed Yagi antenna design to miniaturize the size, extend the bandwidth, and simplify the feeding network. The proposed AiP design is broadband enough to cover all three 5G New Radio bands simultaneously. The high-precision high-resolution multi-layered glass packaging fabrication process with a new low-loss polymer material coating is adopted to realize the circuit. The operation band is from 24.25 GHz to 40 GHz and the fractional bandwidth is 49%. The overall size for an antenna element is 3.05 mm 5.56 mm which is equal to $0.25_0 0.45_0$ . The measured S11 is smaller than -10 dB within the entire band and the gain is larger than 4 dBi. A 2-by-1 array using the proposed element is also demonstrated with a gain higher than 6.2 dBi within the entire band. Compared with previous works, the proposed AiP design can cover all 5G bands with a competitive size. Thus, it is suitable to be applied to massive arrays and easily integrated into packages to achieve compact system-in-package (SiP) applications while resolving numerous current 5G challenges.
21 January 2020 in IEEE Transactions on Components, Packaging and Manufacturing Technology