1 August 2025 in Journal of Traffic and Transportation Engineering (English Edition)
22 December 2023 in Materials Today Sustainability
19 June 2023 in Journal of Materials Science
30 October 2023 in Journal of Transport System Engineering
Vegetable oil derived biolubricant often suffer from low oxidative and thermal oxidative stability, limiting their effectiveness as lubricants. Chemical modification through the addition of additive offers a solution to enhance their physicochemical and tribological properties. This study aims to analyse the impact of incorporating Methyl Laurate (ML) as an additive to Trimethylolpropane (TMP) Trioleate biolubricant and determine the optimal ML concentration. Three types of ML provided by Wilmar Oleochemicals & Biofuels were tested, with ML concentrations ranging up to 15 wt% in TMP trioleate. The double bond content, evaluated through the iodine value (IV), influenced the oxidative stability of the biolubricant. Wettability was assessed using Image J software following ASTM D733, and viscosity-temperature relations were analysed to determine the viscosity index (VI) according to ASTM D445. Results showed that 100% ME1299 ML type exhibited the lowest IV, better wettability, and higher VI. Therefore, adding 15 wt% of 100% ME1299 ML to TMP trioleate yielded the most desirable combination, resulting in improved viscosity-temperature relations compared to the base oil.
4 January 2023 in IIUM Engineering Journal
PEDOT:PSS is a conducting organic polymer widely studied for a transparent conductive electrode. The conventional method to fabricate PEDOT:PSS thin film involves a post-treatment process entailing dipping into strong and toxic saturated acid to enhance the film’s conductivity. Eliminating the post-treatment process reduces excess strong saturated acid or solvent waste, shortening the fabricating time by half. Therefore, this study presents a quick and facile solution-processed method for fabricating the PEDOT:PSS transparent conductive thin film (without a post-treatment process) while still achieving the requirements for a transparent conductive electrode (TCE). A parametric study was conducted by adding 5 wt% to 80 wt% of benzene sulfonic acid (BA) to PEDOT:PSS during the formulation stage before being dried at elevated temperatures from 80 °C to 200 °C. The optimum sheet resistance and transmittance value could be achieved for a thin film fabricated from PEDOT:PSS added with 40 wt% of BA, and dried at 120 °C. The sheet resistance and transmittance values are 80 ?/sq and 93.6%, respectively. The generated figure of merit (FOM) value is 70.1, indicating an improvement of almost five times compared to the FOM value of 14.6 generated using the conventional method, requiring a post-treatment process. ABSTRAK: PEDOT:PSS adalah bahan polimer organik yang mengkonduksi arus dan dikaji secara meluas bagi digunakan sebagai elektrod konduktif telus. Kaedah konvensional untuk menghasilkan filem nipis PEDOT:PSS melibatkan proses pasca rawatan iaitu dengan mencelupkan filem nipis PEDOT:PSS ke dalam asid pekat bertoksik bagi meningkatkan konduksi filem tersebut. Tanpa proses pasca rawatan ini dapat mengurangkan penghasilan sisa lebihan seperti asid pekat bertoksik atau pelarut buangan, memendekkan masa fabrikasi sebanyak separuh. Oleh itu, kajian ini menghasilkan kaedah proses-penyelesaian yang cepat dan mudah bagi fabrikasi filem nipis PEDOT:PSS (tanpa proses pasca rawatan) disamping masih mencapai keperluan sebagai elektrod konduktif telus (TCE). Kajian parametrik telah dijalankan dengan menambah 5 wt% hingga 80 wt% asid sulfonik benzena (BA) ke dalam PEDOT:PSS pada peringkat percampuran kimia sebelum dikeringkan pada kenaikan suhu secara berperingkat dari 80 °C sehingga 200 °C. Nilai optimum bagi rintangan lapisan dan nilai ketelusan bagi filem nipis PEDOT:PSS yang difabrikasi dapat dicapai melalui penambahan sebanyak 40 wt% BA dan dikeringkan pada suhu 120 °C. Rintangan lapisan dan nilai ketelusan telah dicapai sebanyak 80 ?/sq dan 93.6%, masing-masing. Nilai gambaran merit (FOM) yang terhasil adalah 70.1, menunjukkan peningkatan hampir lima kali ganda berbanding nilai FOM 14.6 yang terhasil menggunakan kaedah konvensional yang memerlukan proses pasca-rawatan.