Lin Lu

Lin Lu

Auto-generated profile, based on publicly available information

Lin Lu

School of Information Science and Engineering, Southeast University, Nanjing, China

Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 September 2022 in IEEE Sensors Journal
Verified
Journal Article
Closed access
LLLin Lu
Lin Lu
XMXujun Ma
Xujun Ma
YLYue Liang
Yue Liang
ZLZhiqiang Liu
Zhiqiang Liu
XFXiangning Fan
Xiangning Fan
LLLianming Li
Lianming Li
In the field of non-contact sensing, both the continuous-wave (CW) Doppler radar and the frequency-modulated continuous-wave (FMCW) radar have their own superiorities. A combination of these two radar modes would be a suitable choice to accommodate various application scenarios. This paper presents a 60-GHz hybrid FMCW-Doppler radar transceiver fabricated in a 65-nm CMOS process. An on-chip frequency quadrupler driven by a 15-GHz external signal source is utilized for the 60-GHz hybrid waveform generation. Based on the hybrid operating modes, a robust I/Q imbalance calibration method is also proposed. Specifically, in the Doppler radar mode, the imbalance factors are extracted by evaluating the quadrature beat signals during the FMCW period, and then the interferometry signals are calibrated to improve the detection performance. Unlike the trajectory-based ellipse-fitting method, the accuracy of the estimated imbalance factor is independent of the target displacement. Compared with the test-signal-based imbalance factors extraction ahead of the target detection, the real-time extraction during the target detection is more efficient and can also mitigate the estimation errors caused by environmental variations. With the proposed hybrid radar system and the I/Q calibration method, an 80-mm linear displacement is recovered with a 0.016-mm root mean square error (RMSE), and a periodic vibration with a 1-μm amplitude is detected with a 16.4-dB signal-to-noise ratio (SNR). Multiple-target detection is also performed in the FMCW radar mode, and the vibration trajectories are recovered accurately.

14 October 2024 in IEEE Transactions on Microwave Theory and Techniques
Verified
Journal Article
Closed access
LLLin Lu
Lin Lu
XMXujun Ma
Xujun Ma
JFJing Feng
Jing Feng
LHLong He
Long He
XFXuewei Fan
Xuewei Fan
LLLianming Li
Lianming Li
A 60-GHz joint radar–communication (JRC) transceiver is presented in this article. To achieve a compact JRC transceiver architecture with highly reused RF modules, a dedicated reconfigurable dual-mode Gilbert cell is proposed. Specifically, in the communication mode, the dual-mode Gilbert cells operate as conventional upconversion mixers to modulate the baseband (BB) communication data, while it could also be configured as an amplifier to strengthen the LO signal in the radar mode. Compared with the quadrature IF chirp modulation scheme in which the chirp bandwidth is constrained by the narrowband IF devices, in this work, a wideband chirp generated directly from the LO chain could be applied for radar sensing, significantly improving the range resolution in the radar mode. Besides, the direct RF dechirping could also relieve the hardware burden during radar signal processing compared with the digital dechirping utilized in the IF chirp modulation scheme. Fabricated in a 65-nm CMOS process, this JRC transceiver realizes an ultracompact chip size, and a 16-dBm saturated TX output power, an 11-dBm OP $_{\text{1\,dB}}$ , and a 5.8-dB minimum RX noise figure (NF) are also achieved. Experiments demonstrate that the proposed JRC transceiver supports $>$ 4-GHz transmitted chirp bandwidth with $<$ 3.75-cm range resolution in the radar mode, and a mechanical vibration with 1- $\mu$ m displacement is successfully detected. Besides, a $>$ 7-Gb/s data rate in the 16-QAM over-the-air (OTA) communication is also demonstrated.

27 March 2024 in IEEE Microwave and Wireless Technology Letters
Verified
Journal Article
Closed access
JFJing Feng
Jing Feng
LLLin Lu
Lin Lu
XCXin Chen
Xin Chen
YSYi Sun
Yi Sun
XWXu Wu
Xu Wu
LLLianming Li
Lianming Li
This letter presents a four-stage variable-gain power amplifier (VGPA) for 60-GHz time division duplex (TDD) phased array systems. To reduce the loading effect of the off-state VGPA on the receiver (Rx), a switchable inductor is proposed as an antenna transmit/receive switch (TRSW), which introduces low insertions loss to the VGPA output matching in transmitter (Tx) mode while providing a high off-impedance in Rx mode. To improve the output dynamic range, a Gilbert-based X-type variable-gain stage with low phase variation is designed. With measurements, the VGPA realizes a 25.4-dB peak gain with a BW $_{\text{{3\,dB}}}$ from 49 to 67 GHz, and a $<$ 2.6 $^{\circ}$ rms phase error is achieved over a 15-dB gain tuning range. The measured OP $_{\text{1\,dB}}$ , $P_{\text{sat}}$ , OIP $_{\text{3}}$ , PAE $_{\text{1\,dB}}$ , and PAE $_{\text{max}}$ are 11.3, 12.2, 16.2 dBm, 6.4%, and 8.9%, respectively. When the PA and the switchable inductor are turned off, a $>$ 180 $~\Omega$ output off-impedance is achieved over the interested frequency range.

2 February 2024 in IEEE Microwave and Wireless Technology Letters
Verified
Journal Article
Closed access
LLLin Lu
Lin Lu
XMXujun Ma
Xujun Ma
JFJing Feng
Jing Feng
QCQin Chen
Qin Chen
DCDepeng Cheng
Depeng Cheng
LLLianming Li
Lianming Li
Caused by inappropriate allocation of the interstage power mismatches during broadband matching, the boosted dynamic dc current of the frequency doubler (FD) would deteriorate the broadband efficiency. To tackle this issue, an efficiency-optimized broadband matching strategy is proposed by allocating all of the desired low-frequency mismatches ahead of the push-push (PP) pair, which not only keeps a broadband output but also reduces the dynamic dc current and improves the efficiency over the entire operating bandwidth simultaneously. To further enhance the 2nd harmonic (HR2) output power, a fourth-order notch filter is also designed at the PP pair input. Fabricated in a 65-nm CMOS process, the proposed Ka-band FD exhibits $>$ 15% efficiency from 24.6 to 36 GHz, and a 23.5% peak efficiency is achieved. A 42.6% fractional bandwidth (FBW) is also realized with a fundamental rejection ratio (FRR) over 45 dBc.

30 April 2012 in Journal of Modern Optics
Verified
Journal Article
Closed access
QLQieni Lü
Qieni Lü
LLLin Lu
Lin Lu
BGBaozhen Ge
Baozhen Ge
DWDi Wu
Di Wu
Hao WuHao Wu
Hao Wu
A differential laser trigonometry method is presented for measurement of the oil film thickness on a water surface. The thickness of an oil film can be obtained with two off-plane displacements to a benchmark plane obtained by the imaging spot displacement and the configuration parameter of the imaging system subtracted. The method has been tested in the laboratory via the examination of diesel oil and petroleum films. An experimental system setup has been developed, by which the maximum measurable thickness is 12 mm and the average measurement error is 6.05 µm. The results show that the method presented is feasible, and applicable to dynamic online measurement of oil film thickness of oil spills on the sea surface.

28 October 2024 in IEEE Microwave and Wireless Technology Letters
Verified
Journal Article
Closed access
JFJing Feng
Jing Feng
YLYue Liang
Yue Liang
XNXiaokang Niu
Xiaokang Niu
LLLin Lu
Lin Lu
XCXin Chen
Xin Chen
LLLianming Li
Lianming Li
This letter proposes an antenna transmit/receive (T/R) switch embedded in the power combiner of the two-way power amplifier (PA) and realizes a 60-GHz fully differential T/R front end (FE). Compared with the traditional standalone single-pole-double-throw (SPDT) switch, only one switch transistor is needed in the PA power combiner and reused for both transmit (TX) and receive (RX) modes, thereby significantly reducing the chip area and the insertion loss. With careful codesign of the switch with the PA and low-noise amplifier (LNA) matching networks, the insertion loss introduced by the switch and the loading effect could be reduced to 0.5 and 1 dB in the TX and RX modes, respectively. Fabricated in a 65-nm CMOS process, the PA achieves a power gain, OP $_{\mathrm{1\, dB}}$ , P $_{\mathrm{sat}}$ , and PAE $_{\mathrm{max}}$ of 25 dB, 11 dBm, 16 dBm, and 16%, respectively. Benefitting from the low loss of the switch, the LNA attains a peak gain and noise figure (NF) of 25 and 6.4 dB, respectively.