30 October 2018 in IEEE Transactions on Microwave Theory and Techniques
This paper presents a 1.7-mW low-intermediate-frequency receiver design for Bluetooth low-energy (BLE) applications. The design exploits particular aspects of BLE, such as the relaxed in-band interference characteristics, more precisely the C/I₁ MHz, and the relatively high-frequency-shift keying modulation index, to deliver a high level of energy efficiency and simplicity to the receiver baseband architecture. Reliable quadrature signals are generated in the RF signal path without consuming energy, which is supported by an inverter-based low-noise amplifier (LNA) that achieves high gain and low noise figure under low-power budgets. A small-signal analysis of low-power inverter-based LNAs is presented offering simple design equations. Seeking an affordable solution, the fabricated prototype is fully integrated into an earlier generation CMOS technology node (0.13 μm), occupying a silicon area smaller than 0.7 mm². The receiver achieves a sensitivity level of -92 dBm while consuming 1.41 mA from a 1.2-V supply.
20 February 2020 in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
Current-mode class-D (CMCD) power amplifiers (PAs) may not achieve a switching efficiency as good as class-E PAs, but they require fewer inductances and deliver almost five times more power for the same load and supply voltage when compared with the ideal push-pull class-E PA. Furthermore, CMCD PAs can easily use bondwires as the only circuit inductors, a precious feature that Internet-of-Things (IoT) wireless interfaces can exploit. For this reason, we analyze the voltage and current waveforms in CMCD PAs without assuming infinite value feeding inductors (i.e., without choke inductors). It is shown that the current stress on the switching device is significantly higher than in the conventional topology, especially in bondwire-based designs where relatively small feeding inductances are presented. Finally, we propose a design procedure for a given feeding inductance that maximizes energy efficiency while delivering a compact-size solution. A 2.4-GHz PA capable of delivering 19.8 dBm to a 100-Ω differential load with a power-added-efficiency (PAE) of 58% is presented. Three-dimensional electromagnetic (3-D EM) simulations combined with postlayout simulations were used to evaluate the PA performance in a quad-flat nonlead (QFN)-type package. The circuit is designed in a 0.13-μm process and only occupies a silicon area of 0.025 mm 2 .
19 May 2016 in IEEE Microwave and Wireless Components Letters
This letter presents an all-digital low-IF Gaussian Frequency-Shift Keying (GFSK) demodulator. The demodulator is based on a quadrature FM discriminator followed by a bit decision unit. An intermediate-frequency (IF) input signal of 1MHz is used, the same value of the data rate, hence allowing a low-power receiver implementation. By monitoring the SNR of the input packet during the preamble, poor SNR packets are discarded to avoid energy waste with non-decodable packets. The circuit occupies a silicon area of 0.048 mm 2 in a 130nm process. Measurements show a state-of-the-art current consumption of about 170 μA from a single 1.2V supply. The proposed demodulator requires an SNR of 14.4 dB for a BER of 0.1%.
7 February 2018 in IEEE Solid-State Circuits Letters
This paper presents a fully integrated single-ended power amplifier for ultra-low-power applications. The single-ended configuration is possible due to a choke-inductor less output network capable of rejecting the 2nd-harmonic emission. A switching duty-ratio lower than 50% avoids the impedance transformation output network traditionally required for proper class-E operation. At 2.45 GHz, the PA (including the driver) delivers 1.4 dBm to a 50 Ω load and achieves an overall efficiency of 51% while complying with the spurious emission regulation. The prototype was fabricated in 0.13 μm CMOS.