Dawn E. Lehman

Dawn E. Lehman

Auto-generated profile, based on publicly available information

Dawn E. Lehman

Department of Civil and Environmental Engineering University of Washington Seattle Washington USA

Research Focus & Metrics

Academic Career Length

19Years (2008-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 December 2016 in Journal of Structural Engineering
Verified
Journal Article
Closed access
ASAndrew D. Sen
Andrew D. Sen
CRCharles W. Roeder
Charles W. Roeder
JBJeffrey W. Berman
Jeffrey W. Berman
DLDawn E. Lehman
Dawn E. Lehman
CLChao-Hsien Li
Chao-Hsien Li
KTKeh-Chyuan Tsai
Keh-Chyuan Tsai
Steel concentrically braced frames designed prior to the implementation of capacity design principles in seismic design provisions may exhibit poor inelastic response under seismic excitation. These older, nonductile concentrically braced frames (NCBFs) used several configurations, with the chevron configuration being one of the most common. The response of chevron-configured NCBFs is unknown, as relatively large axial and flexural demands are imposed on the beam after brace buckling. Current code requirements for special concentrically braced frames (SCBFs) promote full yielding of the braces while the beam remains elastic, but NCBFs develop a mechanism in which the beam yields, deforms plastically, and limits tensile elongation of the brace. However, if ductile, this plastic mechanism may meet current performance limits and not require retrofitting. To examine this issue, four tests of two-story NCBFs were conducted at the National Center for Research on Earthquake Engineering in Taipei, Taiwan....

1 August 2013 in Journal of Structural Engineering
Verified
Journal Article
Closed access
DLDawn E. Lehman
Dawn E. Lehman
JTJacob A. Turgeon
Jacob A. Turgeon
ABAnna C Birely
Anna C Birely
CHChristopher R. Hart
Christopher R. Hart
KMKenneth P. Marley
Kenneth P. Marley
LLLaura N. Lowes
Laura N. Lowes
RC core walls are used commonly in modern building construction as the primary lateral load–resisting system. To meet architectural constraints, including elevator, stair, and doorway openings, common configurations include walls coupled together with heavily reinforced, low-aspect-ratio coupling beams. Numerous studies have focused on coupling beams and improved seismic performance and design of coupling beams. However, far fewer research programs have studied the seismic behavior of the coupled wall system. Coupled walls are typically used in mid- to high-rise construction, and understanding their seismic response requires simulation beyond the coupling beam and must include all important yielding components of the system. A research project was undertaken to investigate the response of a midrise coupled wall designed to meet current codes. The advanced testing capabilities of the University of Illinois at Urbana-Champaign George E. Brown, Jr. Network for Earthquake Engineering Simulation (NEES)...

1 September 2016 in Journal of Structural Engineering
Verified
Journal Article
Closed access
MSMax T. Stephens
Max T. Stephens
LBLisa M. Berg
Lisa M. Berg
DLDawn E. Lehman
Dawn E. Lehman
CRCharles W. Roeder
Charles W. Roeder
Concrete-filled steel tubes (CFSTs) frequently are a more efficient and economical structural solution then conventional reinforced concrete and structural steel. For the same size member, CFSTs offer increased strength and stiffness as well as accelerated construction. CFSTs may be used for bridge columns that will yield under earthquake loading, but this requires robust connections capable of sustaining large cyclic loads. To facilitate accelerated bridge construction, precast cap beams and girders are commonly used. Although CFST column-to-foundation connections have been studied, CFST column-to-precast cap beam connections have not. This is the focus of this research study. In contrast to cast-in-place (CIP) components, precast pier cap connections require additional design considerations including construction methodology and limits on geometry. To investigate this connection an integrated analytical and experimental research program was performed. Initially, continuum finite-element methods ...

1 September 2016 in Journal of Structural Engineering
Verified
Journal Article
Closed access
ASAndrew D. Sen
Andrew D. Sen
DSDaniel Sloat
Daniel Sloat
RBRyan Ballard
Ryan Ballard
MJMolly M. Johnson
Molly M. Johnson
CRCharles W. Roeder
Charles W. Roeder
JBJeffrey W. Berman
Jeffrey W. Berman
Concentrically braced frames (CBFs) have been used as seismic force resisting systems in steel structures for many decades. CBFs designed prior to about 1988 were not capacity designed for the expected brace strength, and many are therefore prone to undesirable failure modes when subjected to large earthquakes. The consequences of other factors, such as weld toughness, gusset plate clearance to permit brace end rotation, and local slenderness of the brace, were also not fully understood, so older CBFs may also exhibit premature failure relative to modern, special CBFs (SCBFs). Thus, these older CBFs are expected to exhibit low inelastic deformation capacity and are termed nonductile CBFs (NCBFs) here. An infrastructure review showed that many NCBFs are deficient by SCBF standards and an experimental program was undertaken to explore the impact of brace and connection deficiencies in particular. Brace local slenderness and brace-to-gusset plate weld deficiencies were found to be highly detrimental ...

21 July 2020 in Earthquake Engineering & Structural Dynamics
Verified
Journal Article
Closed access
PDF file
HAHayato Asada
Hayato Asada
ASAndrew D. Sen
Andrew D. Sen
Tao LiTao Li
Tao Li
JBJeffrey W. Berman
Jeffrey W. Berman
DLDawn E. Lehman
Dawn E. Lehman
CRCharles W. Roeder
Charles W. Roeder

1 May 2017 in Journal of Structural Engineering
Verified
Journal Article
Closed access
ASAndrew D. Sen
Andrew D. Sen
MSMarsha A. Swatosh
Marsha A. Swatosh
RBRyan Ballard
Ryan Ballard
DSDaniel Sloat
Daniel Sloat
MJMolly M. Johnson
Molly M. Johnson
JBJeffrey W. Berman
Jeffrey W. Berman
Concentrically braced frames (CBFs) have been used for seismic-lateral-force resisting systems for many years, but prior to approximately 1988, they were not designed to promote ductile response using capacity-based design. These older, nonductile CBFs (NCBFs) have been investigated in prior research that identified severe deficiencies in these systems, but some deficiencies had more detrimental consequences than others. This paper describes a research study to evaluate retrofit strategies for NCBFs. Welded and bolted continuous and split shear-plate connections, end-plate connections, split double-angle connections, and integrated gusset-shear plate connections were investigated. Retrofit strategies included brace replacement, concrete in-fill of a locally slender brace, weld overlay, bolt reinforcement, development of in-plane brace buckling, and the use of buckling-restrained braces. In all cases, system deformation capacity was enhanced, and the extent of improvement depended on connection con...