10 May 2022 in Natural Hazards and Earth System Sciences
Flood events are the most frequent cause of damage to infrastructure compared to any other natural hazard, and global changes (climate, socioeconomic, technological) are likely to increase this damage. Transportation infrastructure systems are responsible for moving people, goods and services, and ensuring connection within and among urban areas. A failed link in these systems can impact the community by threatening evacuation capability, recovery operations and the overall economy. Bridges are critical links in the wider urban system since they are associated with little redundancy and a high (re)construction cost. Riverine bridges are particularly prone to failure during flood events; in fact, the risks to bridges from high river flows and erosion have been recognized as crucial at global level. The interaction of flow, structure and network is complex, and not fully understood. This study aims to establish a rigorous, multiphysics modeling approach for the assessment of the hydrodynamic forces impacting inundated bridges, and the subsequent structural response, while understanding the consequences of such impact on the surrounding network. The objectives of this study are to model hydrodynamic forces as demand on the bridge structure, to advance a performance evaluation of the structure under the modeled loading, and to assess the overall impact at systemic level. The flood-prone city of Carlisle (UK) is used as a case study and a proof of concept. Implications of the hydrodynamic impact on the performance and functionality of the surrounding transport network are discussed. This research will help to fill the gap between current guidance for design and assessment of bridges within the overall transport system.
1 June 2019 in Journal of Constructional Steel Research
1 December 2016 in Journal of Structural Engineering
Steel concentrically braced frames designed prior to the implementation of capacity design principles in seismic design provisions may exhibit poor inelastic response under seismic excitation. These older, nonductile concentrically braced frames (NCBFs) used several configurations, with the chevron configuration being one of the most common. The response of chevron-configured NCBFs is unknown, as relatively large axial and flexural demands are imposed on the beam after brace buckling. Current code requirements for special concentrically braced frames (SCBFs) promote full yielding of the braces while the beam remains elastic, but NCBFs develop a mechanism in which the beam yields, deforms plastically, and limits tensile elongation of the brace. However, if ductile, this plastic mechanism may meet current performance limits and not require retrofitting. To examine this issue, four tests of two-story NCBFs were conducted at the National Center for Research on Earthquake Engineering in Taipei, Taiwan....
1 September 2016 in Journal of Structural Engineering
Concentrically braced frames (CBFs) have been used as seismic force resisting systems in steel structures for many decades. CBFs designed prior to about 1988 were not capacity designed for the expected brace strength, and many are therefore prone to undesirable failure modes when subjected to large earthquakes. The consequences of other factors, such as weld toughness, gusset plate clearance to permit brace end rotation, and local slenderness of the brace, were also not fully understood, so older CBFs may also exhibit premature failure relative to modern, special CBFs (SCBFs). Thus, these older CBFs are expected to exhibit low inelastic deformation capacity and are termed nonductile CBFs (NCBFs) here. An infrastructure review showed that many NCBFs are deficient by SCBF standards and an experimental program was undertaken to explore the impact of brace and connection deficiencies in particular. Brace local slenderness and brace-to-gusset plate weld deficiencies were found to be highly detrimental ...
21 July 2020 in Earthquake Engineering & Structural Dynamics
1 May 2017 in Journal of Structural Engineering
Concentrically braced frames (CBFs) have been used for seismic-lateral-force resisting systems for many years, but prior to approximately 1988, they were not designed to promote ductile response using capacity-based design. These older, nonductile CBFs (NCBFs) have been investigated in prior research that identified severe deficiencies in these systems, but some deficiencies had more detrimental consequences than others. This paper describes a research study to evaluate retrofit strategies for NCBFs. Welded and bolted continuous and split shear-plate connections, end-plate connections, split double-angle connections, and integrated gusset-shear plate connections were investigated. Retrofit strategies included brace replacement, concrete in-fill of a locally slender brace, weld overlay, bolt reinforcement, development of in-plane brace buckling, and the use of buckling-restrained braces. In all cases, system deformation capacity was enhanced, and the extent of improvement depended on connection con...