High lumen-density laser lighting has become an advanced lighting technology. However, as an important component, transparent light-conversion materials exhibit low efficiency and luminescence declining behaviors, especially under high power density lasers, seriously restricting their potential applications. Herein, high quality YAG:Ce transparent ceramics (TCs) with different Ce concentrations and sizes were designed and fabricated for comparison with YAG:Ce single crystals to reveal the nature behind the above phenomena under the assistance of different encapsulated models of LED/LD devices. The highest luminous efficiency for the TCs of over 248 lm W−1 was achieved in the LED device, while only 170 lm W−1 could be reached for the LD devices. The strong thermal quenching and concentration quenching worked synergistically to result in the luminescence declining behavior in the 0.5 at% YAG:Ce ceramics, which have 80% and 20% responsibility after smart experimental comparison, respectively. Besides, the potential factors for the low efficiency in TC-based LD lighting were also revealed. Therefore, this work not only shows the optical performance of TCs in LED and LD applications, but also presents how the deep influence factors and excitation models lead to differences in their performance. It significantly reinforces the understanding of fundamental problems for TC-based high power laser lighting. These results are crucial for advancing TC-supported technologies in illumination, projection and scintillation.
12 October 2020 in Journal of Materials Chemistry C
Transparent ceramics (TCs) with high quantum efficiency and excellent thermal stability are essential for the applications in high-power remote excitation white light-emitting diode or laser diode (LED/LD) lighting devices as color convertors. In this study, based on the “local complexity of Ce3+ ion coordination environment effect” and “effective ionic radius match effect”, an effective regulation of the phase composition and spectral properties was realized in LuAG TCs by incorporating Y3+ and Sc3+ ions. A series of Ce:(Lu,Y)3(Al,Sc)2Al3O12 (Ce:LuYSAG) TCs were fabricated with a high internal quantum efficiency (IQE) of 86.7%. The prepared TCs exhibited a distinct red-shift (520 → 541 nm) and a 10.2% increase of full width at half maximum (FWHM) in the emission spectra. Surprisingly, 89.9% of the room temperature emission intensity of the TC was retained at 200 °C. By combining the Ce:LuYSAG TCs with a 460 nm blue chip or a 455 nm laser source, white LED/LD devices in a remote excitation mode were constructed. A tunable hue from cyan-green to pale-green was obtained with increasing Y3+ concentration of TCs. The surface temperature of TCs varied from 112.6 °C to 62 °C under 1.0 W LD irradiation. Upon increasing the power of the blue laser from 1.0 W to 3.5 W, the luminous flux (LF) of the TC with 30 at% Sc3+ and 50 at% Y3+ ions substitution tremendously increased from 250.9 lm to 877.4 lm, and the optimized luminous efficiency of radiation (LER) was as high as 251 lm W−1. Therefore, this work opens up new opportunities for the development of TCs with excellent luminescence performance through manipulation of their local coordination structure for high-power white LEDs/LDs.
High-power, high-brightness laser lighting promotes new requirements for light-conversion materials, such as high thermal conductivity, high saturation threshold and compact encapsulation. In this paper, we designed and fabricated a novel composite structure ceramic including a 1.0 × 1.0 mm2 Al2O3-YAG:Ce ceramic and a φ=16.0 mm transparent YAG ceramic for the transmissive configuration in laser lighting. When pumped by blue laser from 0∼60 W mm2, all the samples exhibited no luminous saturation phenomenon, and the 10.0 wt.%Al2O3-YAG:Ce/YAG composite ceramic with the thickness of 0.3 mm maintained white light with a luminous efficacy over 200 lm/W. Moreover, a maximal luminous flux over 1000 lm, a correlated color temperature (CCT) of 5471 K, and an operating temperature as low as 92.3 °C were obtained under the excitation power density as high as 60 W/mm2. The configuration that Al2O3-YAG:Ce encapsulated by YAG reflects an excellent optical and thermal properties by using transparent and highly thermally conductive YAG materials. These results indicate that Al2O3-YAG:Ce/ YAG composite ceramic phosphor is a promising candidate in transmissive configuration for automotive lighting and laser searchlight.
Ceramic phosphors are widely considered the next-generation phosphor material for white LED/LD lighting, and a wide spectrum is a key factor in improving the CRI of lighting sources. In this paper, a novel, to our knowledge, barcode-structured YAG:Ce/YAG:Ce,Mn ceramic phosphor was designed and fabricated. The lighting sources with the CRI value of 73.5 and 68.9 were obtained under the excitation of blue LEDs and blue LDs, respectively. Simultaneously, thanks to the effective supplementary emission from a red LD, the CRI of the ceramic-based lighting source reached 81.8 under blue LD excitation. Specifically, the microstructure and luminescent property of ceramic phosphors with different thicknesses and ion doping concentrations were systematically studied. Besides, by changing the blue power from 0.52 W to 2.60 W, the CCT of the laser lighting source with the encapsulation of optimized YAG:Ce/YAG:Ce,Mn ceramic phosphors ranged from 3928 K to 5895 K, while the CRI always maintained above 80. The above results indicate that barcode-structured Ce:YAG/Ce,MnYAG ceramic phosphor is a candidate to achieve a high CRI and ican be applied to various lighting occasions.
High power and high brightness laser lighting puts forward new requirements for phosphor converters such as high luminous efficiency, high thermal conductivity and high saturation threshold due to the severe thermal effect. The structure design of phosphor converters is proposed as what we believe to be a novel strategy for less heat production and more heat conduction. In this work, the rod-shaped YAG:Ce phosphor ceramics (PCs) and disc-shaped YAG:Ce PCs as control group were fabricated by the gel casting and vacuum sintering, to comparatively study the luminescence performance for LD lighting, on the premise that the total number of transverse Ce3+ ions and the volume of samples from two comparison groups were same. All rod YAG:Ce PCs with low Ce3+ concentration exhibited the high luminous efficiency and better thermal stability than YAG:Ce discs with high Ce3+ concentration. Under the laser power density of 47.8 W/mm2, the luminous saturation was never observed in all rod-shaped YAG:Ce PCs. The high luminous efficacy of 245∼274 lm/W, CRI of 56.3∼59.5 and CCT of 4509∼4478 K were achieved. More importantly, due to the extremely low Ce3+ doping concentration (0.01 at%), rod-shaped ceramics based LDs devices showed the excellent thermal performance and their surface temperatures were even below 30.5 °C surprisingly under the laser power density of 20.3 W·mm-2 (2 W). These results indicate that the rod shape of phosphor converter is a promising structure engineering for high power laser lighting.