Jiangsu Key Laboratory of Advanced Laser Materials and Devices, School of Physics and Electronic Engineering, Jiangsu Normal University, Xuzhou, P. R. China
Auto-generated profile, based on publicly available information
Bingheng Sun
Jiangsu Key Laboratory of Advanced Laser Materials and Devices, School of Physics and Electronic Engineering, Jiangsu Normal University, Xuzhou, P. R. China
Ce:YAG transparent ceramic, a promising photo-converter for white LED lighting, faces a significant obstacle of post-annealing treatments, which allow the simultaneous elimination of defections and the regulation of the redox state of Ce. In this paper, vacuum as-sintered high quality Ce:YAG ceramics were subjected to various annealing conditions, and their microstructural evolution, and optical and luminescence properties were monitored and studied systematically. The results showed that air annealing efficiently benefited the microstructure and optical transmittance. In addition, the absorption band below 300 nm was strongly dependent on the annealing strategies due to the elimination of defects (e.g. F/F+-type color centers) and charge transfer (CT) between Ce(III) and Ce(IV). By constructing with 1350 °C air annealed Ce:YAG ceramics, a high-performance white LED with a luminous efficiency radiation (LER) exceeding 220 lm W−1 was achieved, thanks to the “protected”-annealing condition, which guaranteed moderate CT from Ce(IV) to Ce(III) due to weakened pump light absorption by defects. Differing from traditional Ce:YAG phosphors, excrescent oxygen vacancies were introduced by annealing Ce:YAG ceramics in hydrogen, leading to deteriorated luminescence properties. Therefore, it is expected that this refined preparation of Ce:YAG photo-convertors could drive the development of white LED lighting.
12 February 2020 in Journal of Materials Chemistry C
High lumen-density laser lighting has become an advanced lighting technology. However, as an important component, transparent light-conversion materials exhibit low efficiency and luminescence declining behaviors, especially under high power density lasers, seriously restricting their potential applications. Herein, high quality YAG:Ce transparent ceramics (TCs) with different Ce concentrations and sizes were designed and fabricated for comparison with YAG:Ce single crystals to reveal the nature behind the above phenomena under the assistance of different encapsulated models of LED/LD devices. The highest luminous efficiency for the TCs of over 248 lm W−1 was achieved in the LED device, while only 170 lm W−1 could be reached for the LD devices. The strong thermal quenching and concentration quenching worked synergistically to result in the luminescence declining behavior in the 0.5 at% YAG:Ce ceramics, which have 80% and 20% responsibility after smart experimental comparison, respectively. Besides, the potential factors for the low efficiency in TC-based LD lighting were also revealed. Therefore, this work not only shows the optical performance of TCs in LED and LD applications, but also presents how the deep influence factors and excitation models lead to differences in their performance. It significantly reinforces the understanding of fundamental problems for TC-based high power laser lighting. These results are crucial for advancing TC-supported technologies in illumination, projection and scintillation.
Ce:YAG transparent ceramics have great potential in white LEDs, especially under high power packaging technology, due to their superior thermal performance. However, their interactions and the synergistic effects among multiple factors limit the in-depth understanding and higher efficiency conversion of these ceramics for popular applications, and the single variable research approach is incapable of addressing the complex and diverse requirements for luminescence performance in as-constructed LED devices. In this work, for the first time, orthogonal experiments were designed to comprehensively evaluate the composite effects of thickness, doping concentration and surface roughness on the luminous efficiency and ideal white light of a constructed device with the assistance of the Taguchi method and one-way variance analysis. High throughput fabrication of ceramics was achieved using the novel Isobam gel casting method plus vacuum sintering. The Ce3+ doping concentration was proved to be the most dominant of these factors for excellent luminescence performance. The optimized factors of ceramics for luminous efficiency were 1.5 mm thickness, 0.2 at% Ce3+ concentration and double-polishing of surface roughness, while the optimized factors for good CIE were 0.4 mm thickness, 0.05 at% Ce3+ concentration and double-polishing. Therefore, this work not only shows how the Taguchi method can achieve a better group of multiple factors, but also how the synergistic effects of these factors work together. They significantly affect the optical properties of Ce:YAG ceramics and their performance in high power LED applications. These results are crucial for advancing transparent ceramics applications.
1 April 2021 in Journal of the European Ceramic Society