Per Nylen

Per Nylen

Auto-generated profile, based on publicly available information

Per Nylen

University West

Research Focus & Metrics

Academic Career Length

29Years (1998-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 November 2019 in Technologies
Verified
Journal Article
Open access
PDF file
Shrikant JoshiShrikant Joshi
Shrikant Joshi
PNPer Nylen
Per Nylen
Coatings are pivotal in combating problems of premature component degradation in aggressive industrial environments and constitute a strategic area for continued development. Thermal spray (TS) coatings offer distinct advantages by combining versatility, cost-effectiveness, and the ability to coat complex geometries without constraints of other in-chamber processes. Consequently, TS techniques like high-velocity oxy-fuel (HVOF) and atmospheric plasma spray (APS) are industrially well-accepted. However, they have reached limits of their capabilities while expectations from coatings progressively increase in pursuit of enhanced efficiency and productivity. Two emerging TS variants, namely high-velocity air-fuel (HVAF) and liquid feedstock thermal spraying, offer attractive pathways to realize high-performance surfaces superior to those hitherto achievable. Supersonic HVAF spraying provides highly adherent coatings with negligible porosity and its low processing temperature also ensures insignificant thermal ‘damage’ (oxidation, decarburization, etc.) to the starting material. On the other hand, liquid feedstock derived TS coatings, deposited using suspensions of fine particles (100 nm–5 µm) or solution precursors, permits the production of coatings with novel microstructures and diverse application-specific architectures. The possibility of hybrid processing, combining liquid and powder feedstock, provides further opportunities to fine tune the properties of functional surfaces. These new approaches are discussed along with some illustrative examples.

28 January 2018 in Materials Science and Technology
Verified
Journal Article
Open access
CKChamara Kumara
Chamara Kumara
DDDunyong Deng
Dunyong Deng
Johan MoverareJohan Moverare
Johan Moverare
PNPer Nylén
Per Nylén
Owing to the inherent nature of the process, typically material produced via electron beam melting (EBM) has a columnar microstructure. As a result of that, the material will have anisotropic mechanical properties. In this work, anisotropic elastic properties of EBM built Alloy 718 samples at room temperature were investigated by using experiments and modelling work. Electron backscatter diffraction data from the sample microstructure was used to predict the Young’s modulus. The results showed that the model developed in the finite element software OOF2 was able to capture the anisotropy in the Young’s modulus. The samples showed transversely isotropic elastic properties having lowest Young’s modulus along build direction. In addition to that, complete transversely isotropic stiffness tensor of the sample was also calculated. This paper is part of a thematic issue on Nuclear Materials.

31 March 2016 in Coatings
Verified
Journal Article
Open access
PDF file
Esmaeil SadeghiEsmaeil Sadeghi
Esmaeil Sadeghi
NMNicolaie Markocsan
Nicolaie Markocsan
PNPer Nylén
Per Nylén
There is an increasing demand to replace Co-based coatings with cheap and environmentally friendly Fe-based coatings in corrosive environments. The main objective of this work was to evaluate whether Fe-based coatings could present a better corrosion performance than Co-based coatings. Therefore, two types of Fe-based and one type of Co-based coatings with chemical compositions (in wt %) of Fe-28Cr-16Ni-1.85C (FeNiCrC), Fe-17Cr-12Ni (FeNiCr), and Co-28Cr-1C (CoCrC) were produced by High Velocity Air Fuel (HVAF) spraying. The corrosion behavior of the coatings was studied comparatively by electrochemical tests in 3.5 wt % NaCl solution at 25 °C. The polarization test results showed that the FeCrNiC coating protected the underlying substrate better than the CoCrC coating, while the FeCrNi coating failed to hinder the penetration of corrosive ions. Electrochemical impedance spectroscopy (EIS) measurements revealed that the solution penetrated into the coating through defects, however the corrosion process slowed down due to clogging of the interconnected defects by corrosion products. Increasing the in-flight average particle temperature from 1400 °C to 1500 °C led to a denser coating with fewer defects which seemed to improve the corrosion resistance of the FeCrNiC coating. The high-alloyed Fe-based coatings had the best corrosion protection performance and can thus be recommended as a potential alternative to Co-based coatings.

1 May 2017 in Surface and Coatings Technology
Verified
Journal Article
Closed access
Pawel SokolowskiPawel Sokolowski
Pawel Sokolowski
PNPer Nylen
Per Nylen
RMRadek Musalek
Radek Musalek
LŁLeszek Łatka
Leszek Łatka
Stefan KozerskiStefan Kozerski
Stefan Kozerski
Lech PawlowskiLech Pawlowski
Lech Pawlowski

21 October 2016 in Journal of Applied Crystallography
Verified
Journal Article
Open access
PDF file
CLC. Li
C. Li
SJS. D. M. Jacques
S. D. M. Jacques
Ying ChenYing Chen
Ying Chen
DDD. Daisenberger
D. Daisenberger
Ping XiaoPing Xiao
Ping Xiao
RCR. J. Cernik
R. J. Cernik
The average residual stress distribution as a function of depth in an air plasma-sprayed yttria stabilized zirconia top coat used in thermal barrier coating (TBC) systems was measured using synchrotron radiation X-ray diffraction in reflection geometry on station I15 at Diamond Light Source, UK, employing a series of incidence angles. The stress values were calculated from data deconvoluted from diffraction patterns collected at increasing depths. The stress was found to be compressive through the thickness of the TBC and a fluctuation in the trend of the stress profile was indicated in some samples. Typically this fluctuation was observed to increase from the surface to the middle of the coating, decrease a little and then increase again towards the interface. The stress at the interface region was observed to be around 300 MPa, which agrees well with the reported values. The trend of the observed residual stress was found to be related to the crack distribution in the samples, in particular a large crack propagating from the middle of the coating. The method shows promise for the development of a nondestructive test for as-manufactured samples.

19 October 2013 in Journal of Thermal Spray Technology
Verified
Journal Article
Closed access
PDF file
CLChristophe Lyphout
Christophe Lyphout
AFAngelica Fasth
Angelica Fasth
PNPer Nylen
Per Nylen