Sakahisa Nagai

Sakahisa Nagai

Auto-generated profile, based on publicly available information

Sakahisa Nagai

Department of Advanced Energy, Graduate School of Frontier Sciences, The University of Tokyo, Tokyo, Japan

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 June 2020 in Energies
Verified
Journal Article
Open access
PDF file
OSOsamu Shimizu
Osamu Shimizu
SNSakahisa Nagai
Sakahisa Nagai
TFToshiyuki Fujita
Toshiyuki Fujita
HFHiroshi Fujimoto
Hiroshi Fujimoto
In this study, a novel system named the third-generation wireless in-wheel motor (WIWM-3), which has a dynamic wireless power transfer (DWPT) system, is developed. It can extend the cruise range, which is one of the key specifications of electric vehicles. DWPT also reduces CO2 emission as the driving resistance is reduced due to light weight of the batteries. In this study, CO2 emission by an internal combustion vehicle, a long range drivable electric vehicle with the same cruise range, and an electric vehicle with WIWM-3 equipped with the DWPT system are analyzed using actual measurement data and calculated data based on actual measurement or specification data. A WPT system with WIWM-3 achieves 92.5% DC-to-DC efficiency as indicated by an actual measurement at the nominal position. Thus, the electric vehicle with DWPT can reduce up to 62% of CO2 emission in internal combustion vehicles, and the long-range drivable vehicle emits 17% more CO2 than the electric vehicle with DWPT. Moreover, it is expected that by 2050, electric vehicles with DWPT will reduce CO2 emissions from internal combustion vehicles by 95% in Japan. DWPT systems make electric vehicles more sustainable and, hence, more acceptable for consumers.

22 June 2021 in IEEE/ASME Transactions on Mechatronics
Verified
Journal Article
Closed access
MHMitsuhiro Hattori
Mitsuhiro Hattori
OSOsamu Shimizu
Osamu Shimizu
SNSakahisa Nagai
Sakahisa Nagai
HFHiroshi Fujimoto
Hiroshi Fujimoto
KSKoji Sato
Koji Sato
TNTakuma Nagashio
Takuma Nagashio
Previous studies have proposed various algorithms, such as model predictive control, machine learning, and dynamic programming (DP), for ecological adaptive cruise control (ACC). However, industrial application of these algorithms is limited owing to their considerable computational cost. Moreover, there is a tradeoff between the calculation time and optimization results. In this study, a novel optimization method, referred to as quadrant DP (QDP), for ACC is proposed. QDP is based on regular DP; it divides the DP table into four quadrants. Most of the computations are performed offline, and expensive hardware is not required to be installed in vehicles. Moreover, the offline computation cost is also reduced to a practical level, whereas the result is globally optimal. The algorithm is validated for reducing the energy consumption of an electric vehicle via simulations and experiments using our test vehicle. The experimental results also showed the accuracy of the motor and vehicle dynamics models. Compared with the widely used feedback control for ACC, QDP reduced energy consumption by 16.1% in multilane car following scenarios with the same cruising distance and time. The proposed QDP avoided tradeoffs between computational cost and optimization results by utilizing offline computation effectively. Moreover, it was proven valid for general ecological ACC applications.

24 March 2016 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
SNSakahisa Nagai
Sakahisa Nagai
TNTakahiro Nozaki
Takahiro Nozaki
AKAtsuo Kawamura
Atsuo Kawamura
This paper aims to realize compact actuation systems by sensorless approach. This study adopts solenoid actuators which have advantageous characteristics from the view point in inexpensive cost, simple structure, and high-output force in spite of difficulty in low cost position and force sensing. Some sensorless position estimation techniques for solenoid actuators were reported. However, position and force simultaneous estimation has not sufficiently been achieved. In addition, any real-time feedback control has not been reported. This paper proposes sensorless feedback position control for compact solenoid actuators. The force generation and position/force estimation are conducted by using a dc supply power superposed by an ac component. This control technique has three main features: 1) separation of the power supply into ac and dc components for the position estimation, 2) simultaneous real-time estimation of position and force, and 3) robust feedback position control. Simulations and experiments were conducted for verification of the proposed control with the above three features, and the results indicated that error between the estimation and actual positions was within 0.2 mm. This proposed system offers a new avenue for compact and inexpensive application field.

26 May 2023 in IEEE/ASME Transactions on Mechatronics
Verified
Journal Article
Closed access
YNYuto Naoki
Yuto Naoki
SNSakahisa Nagai
Sakahisa Nagai
HFHiroshi Fujimoto
Hiroshi Fujimoto
Research and development are active in multirotor drones. Attention has been focused on improving drone mobility performance by introducing variable-pitch propellers. However, previous studies have not considered main motor currents in their controller design. The aim of this study is to improve thrust response by controlling the variable-pitch propeller in the thrust dimension while keeping steady-state efficiency. Feed-forward control of thrust by switching modes using the maximum current was designed. The control is designed to switch between a thrust-reaching mode that uses pitch angle and rotational speed and an efficiency-optimizing mode. The mode-switching transitions were verified by simulation, and the effectiveness of the proposal was experimentally validated.

27 September 2024 in IEEE/ASME Transactions on Mechatronics
Verified
Journal Article
Closed access
TUTakumi Ueno
Takumi Ueno
BNBinh-Minh Nguyen
Binh-Minh Nguyen
SNSakahisa Nagai
Sakahisa Nagai
HFHiroshi Fujimoto
Hiroshi Fujimoto
Although driving force control (DFC) has been shown a promising traction control strategy, its practical application is still limited due to the following reasons. First, it is required to use the vehicle chassis velocity to calculate the wheel velocity reference. Second, almost all the existing studies merely utilize the integral force controller without consideration of the windup phenomenon. Third, no stability condition has been proposed to design the controllers systematically. To address the above issues, this article proposes a new cascade configuration for DFC of electric vehicles. The outer layer controls the driving force and directly generates the wheel velocity reference for the inner layer without using the vehicle chassis velocity. The driving force is controlled by an antiwindup proportional-integral controller. Based on the circle criterion, this article establishes a practical oriented stability condition that can be checked conveniently via graphical tests. The effectiveness of the proposal was validated using an electric vehicle developed by our research group. In comparison with the DFC system that employs the conventional integral force control without antiwindup, the proposed approach achieves a 70% reduction in the overshoot at a sudden increase of road friction condition.

1 March 2019 in IEEJ Journal of Industry Applications
Verified
Journal Article
Open access
PDF file
SNSakahisa Nagai
Sakahisa Nagai
RORoberto Oboe
Roberto Oboe
TSTomoyuki Shimono
Tomoyuki Shimono
AKAtsuo Kawamura
Atsuo Kawamura
The in-circuit test is performed by pushing a needle-type probe into the printed circuit board (PCB) and measuring the conductivity between the electronic components. To reduce the testing time and improve the test reliability, a swift and stable motion of the probe is required, especially when the probe touches the surface of the PCB. Instead of the conventional method involving the use of a force sensor, this study investigates the application of a micro electronical mechanical systems accelerometer to realize the quick contacting motion. The detection of the contact instant is evaluated by the jerk signal from this device. Subsequently, a negative force is added to the probe and the proposed force control based on acceleration aided Kalman filter and reaction force observer is applied. The experimental verification indicates that the settling time is reduced to approximately 10ms and this corresponds to nearly 1% of the comparison data based on the existing technique.