8 February 2010 in Computer Methods in Biomechanics and Biomedical Engineering
This work focuses on obtaining realistic human hand models that are suitable for manipulation tasks. A 24 degrees of freedom (DoF) kinematic model of the human hand is defined. The model reasonably satisfies realism requirements in simulation and movement. To achieve realism, intra- and inter-finger constraints are obtained. The design of the hand model with 24 DoF is based upon a morphological, physiological and anatomical study of the human hand. The model is used to develop a gesture recognition procedure that uses principal components analysis (PCA) and discriminant functions. Two simplified hand descriptions (nine and six DoF) have been developed in accordance with the constraints obtained previously. The accuracy of the simplified models is almost 5% for the nine DoF hand description and 10% for the six DoF hand description. Finally, some criteria are defined by which to select the hand description best suited to the features of the manipulation task.
11 July 2022 in IEEE Transactions on Human-Machine Systems
Exoskeletons are wearable robotic devices that surround the anatomy of the user to work in tandem with it. Depending on their structure, exoskeletons can be classified as rigid or flexible. The structure of flexible exoskeletons is made of soft materials, such as fabrics, which adapt to user motion. Therefore, these devices are prone to becoming misaligned with the user, due to improper fitting and slipping of the exoskeleton components on the user body. This article describes a cable-driven exosuit, called LUXBIT, that favors its anatomical adaption to the user by arranging the fabric fibers and sewing patterns to transfer the mobilizing forces. This prototype integrates a novel deformable mechanism that promotes the natural lifting of the arm. LUXBIT is intended for bimanual assistance in daily living, being equipped with a backpack to this end. The results analyzed in this article show that LUXBIT reduces muscle activity in the upper limbs’ flexion by ratios of up to 13.17% and allows the user to hold tiring postures for 62.91% longer.
9 September 2010 in IEEE Transactions on Instrumentation and Measurement
This paper describes data processing using a haptic interface for virtual object grasping tasks. The haptic interface known as MasterFinger-2 (MF-2) is used. This haptic device enables the simulation of object manipulation using the thumb and index finger, which are inserted within thimbles located at the far end of the haptic interface. The experiments were conducted using a setup that provides the operator with two MF-2s. This setup enables bimanual virtual object manipulation. The haptic device provides data about the angular position of all joints and data from four contact sensors located within the thimbles. The values obtained from the angular positions of the joints enable a calculation of the position and orientation of the thimbles, whereas the values obtained from the contact sensors are used to formulate an approximate calculation of the user's force during object manipulation. This information regarding forces enables the segmentation of manipulation tasks and is essentially based on the rising edges produced by the contact sensor signals. After performing task segmentation, the state of the task in progress is detected. This facilitates improvements in user interaction because restrictions can be established in the relationships between the objects that change dynamically depending on the stage of manipulation. This information allows for an improvement in the realism of the simulation because the forces reflected take into account how the relationships between objects vary over the course of the task. Task segmentation is also used to ascertain objects' physical properties. These features are then used to simulate virtual objects with the same properties.
1 February 2013 in Electric Power Systems Research
This paper proposes a method for the identification of different partial discharges (PDs) sources through the analysis of a collection of PD signals acquired with a PD measurement system. This method, robust and sensitive enough to cope with noisy data and external interferences, combines the characterization of each signal from the collection, with a clustering procedure, the CLARA algorithm.\ud \ud Several features are proposed for the characterization of the signals, being the wavelet variances, the frequency estimated with the Prony method, and the energy, the most relevant for the performance of the clustering procedure.\ud \ud The result of the unsupervised classification is a set of clusters each containing those signals which are more similar to each other than to those in other clusters. The analysis of the classification results permits both the identification of different PD sources and the discrimination between original PD signals, reflections, noise and external interferences.\ud \ud The methods and graphical tools detailed in this paper have been coded and published as a contributed package of the R environment under a GNU/GPL license