Narayana Dilip Raja

Narayana Dilip Raja

Auto-generated profile, based on publicly available information

Narayana Dilip Raja

Vel Tech Rangarajan Dr. Sagunthala R&D Institute of Science and Technology

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 September 2022 in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
Verified
Journal Article
Closed access
MSMOHAMED IQBAL SHAJAHAN
MOHAMED IQBAL SHAJAHAN
DNDilip Raja Narayana
Dilip Raja Narayana
NKNaren Shankar Radha Krishnan
Naren Shankar Radha Krishnan
JMJee Joe Michael
Jee Joe Michael
This study shows the contribution of silver nanoparticles mixed with macro-encapsulated phase change material (PCM) in a double slope solar still. Experiments are carried out in three different depths and settings, first using simple double slope solar still, then by addition of PCM, and finally using PCM mixed with silver nanoparticles. Results obtained are compared during the sunshine period and also after sunset. The study shows that the silver nanoparticles in PCM results in reducing the yield and efficiency of the double slope solar still by 7.64% and 5.26% during the charging period. However, it continues to deliver potable water even after sunset due to the stored latent heat in the PCM. The higher thermal capacity of the PCM and the higher thermal conductivity of the silver nanoparticles resulted in a 16% increase in drinking water yield and a 62.53% rise in the thermal efficiency of the double slope solar still. The final cost per liter of the potable water generated using the double slope solar still was reduced to 3.80 INR and the payback time is 2 years which can be reduced further using PCM and nano-enhanced PCM inside the solar still.

15 July 2021 in Journal of Natural Fibers
Verified
Journal Article
Closed access
VMVenkatasudhahar Murugesan
Venkatasudhahar Murugesan
ARA.T. Ravichandran
A.T. Ravichandran
NDN. Dilipraja
N. Dilipraja
Hybrid composite materials containing natural fibers are replacing conventional materials for automobile, aerospace and sports goods structural applications. Fiber extracted from plants and man-made fibers reinforced with polymer matrix find many applications because of improved characteristics, such as light weight and high strength. In this work, fabricated hybrid composites using chemically treated abaca, kenaf and carbon fiber reinforced with epoxy and teta hardener are studied. Hybrid composites have four stacking sequences and five layer composites made up of hand laid up then compression molding. Produced hybrid composites are subjected to various loads to determine the mechanical strength. Moisture absorption measured in the distilled water was used as the medium during water absorption test. Experimental results showed that the treated fiber hybrid composite provided higher mechanical strength and absorbed less moisture. The morphology of fractured surfaces was analyzed by electron microscopy.

Verified
Journal Article
Open access
PDF file
NRNarayana Dilip Raja
Narayana Dilip Raja
KKKammanni Veerabhadrappa Anand Kumar
Kammanni Veerabhadrappa Anand Kumar
Sachin SalunkheSachin Salunkhe
Sachin Salunkhe
HHHussein Mohammed Abdel Moneam Hussein
Hussein Mohammed Abdel Moneam Hussein
The hygroscopic properties of natural fibers tend to degrade the mechanical properties of composite materials. It is essential to investigate the influence of water absorption behavior on the mechanical properties of hybrid composite materials. In this study, hybrid laminate materials consisting of two different reinforcement materials, i.e., Kevlar fibers and jute fibers in the same layer, are considered. Hybrid laminates that have four different weaving patterns: plain weave, basket weave, twill weave, and the satin weave, are tested for their water absorption characteristics. The jute fiber is a naturally extracted fiber that is subjected to chemical treatment. A comparison of mechanical properties before and after treatment of the jute fibers is carried out. Mechanical properties such as tensile strength, compressive strength, flexural strength, impact strength, and hardness are tested. It is found that the mechanical properties improved after the treatment of the jute fibers. The twill weave pattern exhibited negligible defects compared to its counterparts. Chemical treatment of the jute fibers enabled less water being absorbed into the hybrid laminate materials. Mechanical properties improved after using chemically treated jute fibers as the reinforcement material in the hybrid laminate materials. It is concluded that the twill weave pattern and chemical treatment of the natural fibers improved the mechanical properties of the hybrid laminate materials.

11 June 2022 in Journal of Natural Fibers
Verified
Journal Article
Closed access
NRNarayana Dilip Raja
Narayana Dilip Raja
KKKammanni Veerabhadrappa Anand Kumar
Kammanni Veerabhadrappa Anand Kumar
Hybrid laminates were produced using epoxy resin and interwoven fibers of kevlar and jute. In this study, different weaving patterns, i.e.,, plain weave, basket weave, twill weave, and satin weave were considered. Mechanical properties like hardness, tensile strength, flexural strength, compressive strength, and impact strength were experimentally measured. The hybrid laminate having the plain weave and basket weave patterns were observed to have equally spaced pockets of matrix element, which facilitated the isotropic distribution of applied load during the testing of the mechanical properties. The twill weave pattern in the reinforcement exhibited augmented mechanical properties as well as superior elasticity. Its elongation percentage was 32%, while the satin weave pattern exhibited only 21.5%. The satin weave pattern revealed microcracks within the matrix, whereas the twill weave pattern exhibited superior bonding between the matrix and the reinforcement fibers. The twill weave pattern showed anisotropic load transfer during the mechanical test. Thus, the applied load was distributed along the warp direction that contained kevlar fibers. Hence, it exhibited the tensile strength of 6.77 GPa, the flexural strength of 3.4 GPa, the compressive strength of 105.6 MPa, an absorbed maximum impact load of 89 J, and shore-D hardness of 72.2, respectively.

1 January 2021 in Materials Today: Proceedings
Verified
Journal Article
Closed access
DPD. Surrya Prakash
D. Surrya Prakash
NRN. Dilip Raja
N. Dilip Raja

29 October 2021 in International Journal for Simulation and Multidisciplinary Design Optimization
Verified
Journal Article
Open access
PDF file
NRN. Dilip Raja
N. Dilip Raja
NKNaren Shankar Radha Krishnan
Naren Shankar Radha Krishnan
Friction stir welding has been used in automobiles, locomotive, and aircraft structures. This metal joining process exhibits defects like kissing bonds, micropores, and tunnels. Factors like the joining material, joint thickness, tool geometry, and operating parameters control the defects in friction stir welding. The parameters like tool rotation, tool pass speed, and tool force have a greater influence on the joint quality. In this study, these parameters are considered to augment the strength of the joint and minimize defects. The metal matrix composite consisting of AA6061 matrix and 10 wt. % SiCp reinforcement is joined used FSW. The weld parameters were varied between 731 and 1068 rpm tool rotation speed, 0.33 and 1.17 mm/s tool pass speed, and 11 and 28 MPa tool force. The joint strength varied from 165 MPa to 244 MPa. The numerical analysis using ANOVA revealed that compared between the three parameters, the tool force had greater control over the tensile strength of the joint. After optimization, the joint was made at a tool rotation speed of 910 rpm, tool pass speed of 0.77 mm/s, and tool force of 22.33 MPa. The tensile strength increased to 249 MPa after using the optimized weld parameters. The number of defects in the joint was reduced after using the optimized weld parameters.