1 August 2024 in ACS Applied Materials & Interfaces
A lack of sustainability in the design of electronic components contributes to the current challenges of electronic waste and material sourcing. Common materials for electronics are prone to environmental, economic, and ethical problems in their sourcing, and at the end of their life often contribute to toxic and nonrecyclable waste. This study investigates the inkjet printing of flexible humidity sensors and includes biosourced and biodegradable materials to improve the sustainability of the process. Humidity sensors are useful tools for monitoring atmospheric conditions in various fields. Here, an aqueous dispersion of black soldier fly melanin was optimized for printing with a cosolvent and deposited onto interdigitated silver electrodes on flexible substrates. Impedance spectroscopy demonstrated that adding choline chloride increased the ion concentration and AC conductivity by more than 3 orders of magnitude, resulting in a significant improvement in sensing performance and reduced hysteresis. The devices exhibit fast detection (0.8 ± 0.5 s) and recovery times (0.8 ± 0.3 s), with a 170 ± 40-fold decrease in impedance for relative humidity changes from 30% to 90%. This factor is lowered upon prolonged exposure to high humidity in tests over 72 h during which a stable operation is reached. The low embodied energy of the sensor, achieved through material-efficient deposition and the use of waste management byproducts, enhances its sustainability. In addition, approaches for reusability and degradability are presented, rendering the sensor suitable for wearable or agricultural applications.
1 September 2023 in Physiological Measurement
Objective . To explore noise characteristics and the effect physiological activity has on the link between impedance and noise. Approach . Dry-printed electrodes are emerging as a new and exciting technology for skin electro-physiology. Such electrode arrays offer many advantages including user convenience, quick placement, and high resolution. Here we analyze extensive electro-physiological data recorded from the arm and the face to study and quantify the noise of dry electrodes, and to characterize the link between noise and impedance. In particular, we studied the effect of the physiological state of the subject (e.g. rapid eye movement sleep) on noise. Main results . We show that baseline noise values extracted from dry electrodes in the arm are in agreement with the Nyquist equation. In the face, on the other hand, the measured noise values were higher than the values predicted by the Nyquist equation. In addition, we studied how different electrode properties affect performances, including electrode size, shape, and material properties. Significance . Altogether, the results presented here provide a basis for understanding dry electrode performances and substantiate their great potential in electro-physiological investigations.
1 March 2023 in Flexible and Printed Electronics
Bio-impedance measurements are widely used to assess various physiological parameters. Contemporary skin electrodes for bio-impedance measurements are cumbersome and novel electrode designs are needed to allow fast and easy placement, long-term stability and user comfort. This investigation introduces dry, printed, bio-compatible electrode arrays, made of screen-printed carbon and inkjet-printed PEDOT:PSS that measure bio-impedance non-invasively and stably. Two contact impedance measurements yield the lowest normalized values of soft electrodes reported to date. Four contact bio-impedance measurements from the radial, ulnar, common carotid and superficial temporal arteries were performed, demonstrating the ability to capture blood pulsation in different areas with small form factor. Owing to the unique properties of the printed electrodes reported here, we were able to demonstrate for the first time blood pulsation in the face, continuous blood pulsation measurement during simultaneous muscle activation and signal stability over many hours.
25 May 2025 in ACS Applied Materials & Interfaces
The increasing number of sensors contributing to the Internet of Things (IoT) aggravates the e-waste generated globally. Thus, it is an urgent necessity to develop more sustainable sensors. This paper presents a fully inkjet-printed dual-response (electrical and visual) humidity sensor based on hydroxypropyl cellulose (HPC) and the ionic liquid bis(1-butyl-3-methylimidazolium) tetrachloronickelate ([Bmim]2[NiCl4]). The active layer was printed on interdigitated silver electrodes on a flexible cellulose acetate substrate. The optimized ink includes HPC, [Bmim]2[NiCl4], ethylene glycol, water, and Tergitol. HPC and the IL exhibit excellent compatibility, forming homogeneous films without phase separation even at high IL concentration. The printed sensor for an IL content of 50 wt % demonstrates a proportional response when varying the relative humidity (RH) from 30 to 90 RH%, with a high sensitivity of 163, comparable to that of a commercial reference sensor, a low hysteresis of 1.5 RH%, and a fast response time of 0.8 s. In addition, a visual response from colorless to cyan is observed upon dehydration. This color change is visible to the naked eye for a relative humidity below 30 RH% when a transmittance lower than 93% is obtained in the visible spectra. This dual-response humidity sensor, fabricated from sustainable materials and low-cost printing technology, has great potential for a variety of applications, including environmental monitoring, smart agriculture, fire safety, and quality control in the food industry.
23 May 2025 in ACS Applied Electronic Materials
4 February 2025 in Advanced Materials Technologies
The rapid development of the Internet of Things (IoT), artificial intelligence, robotics, and wearable electronics has created new challenges and increased the demand for advanced sensing technologies. These sensors must not only exhibit tailored performance but also offer new properties like stretchability and flexibility while being compatible with industrial manufacturing. In this work, a streamlined and simplified method is introduced for fabricating stretchable Organic Photodiodes (OPDs) relying solely on industry‐grade inkjet‐printing. It is demonstrated that printed stiff islands effectively decouple strain from the stretched substrate and serve as a chemically resistant and mechanically rigid platform for printed OPDs. Printing difficulties that arose while processing the Ag electrodes on the curved island surfaces are overcome by a two‐step printing process. Finally, the study reports fully printed OPDs exhibiting peak responsivities (λ = 730 nm) of 340 mA W −1 and specific detectivities (D*) of 2.8 · 10 11 Jones at 100 Hz, both measured at −2 V. The light sensors remained functional for over 600 mechanical stretching cycles at strains up to 7%.