Wide‐bandgap perovskite solar cells (WBG‐PSCs), when partnered with Si bottom cells in tandem configuration, can provide efficiencies up to 44%; yet, the development of stable, efficient, and scalable WBG‐PSCs is required. Here, the utility of the hybrid evaporation‐solution method (HESM) is investigated to meet these demanding requirements via its unique advantages including ease of control and reproducibility. A PbI2/CsBr layer is co‐evaporated followed by coating of organic‐halide solutions in a green solvent. Bandgaps between 1.55–1.67 eV are systematically screened by varying CsBr and MABr content. Champion efficiencies of 21.06% and 20.35% in cells and 19.83% and 18.73% in mini‐modules (16 cm2) for perovskites with 1.64 and 1.67 eV bandgaps are achieved, respectively. Additionally, 18.51%‐efficient semi‐transparent WBG‐PSCs are implemented in 4T perovskite/bifacial silicon configuration, reaching a projected power output of 30.61 mW cm−2 based on PD IEC TS 60904‐1‐2 (BiFi200) protocol. Despite similar bandgaps achieved by incorporating Br via MABr solution and/or CsBr evaporation, PSCs having a perovskite layer without MABr addition show significantly higher thermal and moisture stability. This study proves scalable, high‐performance, and stable WBG‐PSCs are enabled by HESM, hence their use in tandems and in emerging applications such as indoor photovoltaics are now within reach.
Characterization of perovskite–silicon (Pero/Si) tandem solar cells in an industrial environment is hampered by several challenges. First, the monolithic series connection of the two subcells and the fact that the entire stack shares only two electrical terminals make it impossible to probe each subcell independently. Second, the perovskite absorber's metastability—most notably ion migration—introduces additional, often slow, time‐dependent effects. Together with the industry's requirement for high throughput, these factors complicate accurate, high‐speed characterization. In this work we propose a concept to acquire I–V data for tandem solar cells from light‐emitting diode (LED)‐based solar simulators, where we acquire an approximation of the external quantum efficiency from LED‐based measurements before conducting an I–V measurement with an adjusted LED illumination spectrum. We present results on a reference III/V and different Pero/Si solar cells. We model ion migration in perovskite subcells, which allows for assessing preconditioning and transient effects in I–V cell measurements. We recommend a short preconditioning under light to stabilize the scan time dependence and show the potential for transfer between industrial and lab conditions. Finally, we showcase concepts of camera‐based luminescence measurements for inline analysis. Specifically, we show a line‐scan photoluminescence approach, a fast electroluminescence (EL) imaging approach based on parallel data acquisition with two cameras, and an EL concept based on the application of one RGB camera.
Long‐term reliability of high‐efficiency tunnel oxide passivated contact (TOPCon) and silicon‐heterojunction (HJT) modules seem threatened by ultraviolet light‐induced degradation (UVID), yet the kinetics and triggers of the defect mechanisms remain poorly understood. We systematically investigate UVID in unencapsulated industrial solar cells under variations of UV spectrum, intensity, temperature, and concurrent visible illumination (VIS) and correlate resulting losses with hydrogen redistribution measured by ToF‐SIMS. Short‐wavelength UV photons strongly enhance UVID and drive near‐surface defect formation, whereas elevated cell temperatures during exposure substantially suppress degradation. For a fixed exposure time, the defect generation scales linearly with cumulative UV photon dose, but the net UVID amplitude depends critically on the accumulated thermal budget. Under combined UV + VIS illumination near‐outdoor conditions, although at open contacts, UVID is almost completely suppressed, indicating that continuous carrier injection promotes repassivation and prevents stable defect buildup. Post‐UV dark storage induces additional metastable degradation in the TOPCon group, which, like the initial UVID, is reversible by visible light soaking at elevated temperature. Our results substantiate hydrogen‐mediated interface changes as the most likely key driver of UVID and highlight that accelerated UV tests must account for spectral shape, temperature history, and concurrent VIS illumination to reproducibly determine UVID in field performance.
In this study, BiNPs&PEI N‐GQDs nanocomposites were synthesized via a green approach by incorporating bismuth nanoparticles (BiNPs) into polyethyleneimine‐functionalized nitrogen‐doped graphene quantum dots (PEI N‐GQDs). The nanocomposites were characterized using Transmission Electron Microscopy, Ultraviolet–Visible Spectroscopy, Fourier‐Transform Infrared Spectroscopy, x‐ray Photoelectron Spectroscopy, Ultraviolet Photoelectron Spectroscopy, and Photoluminescence Spectroscopy. The photoluminescence spectra exhibited dual emission bands at ∼2.95 eV (420 nm) and ∼2.42 eV (512 nm). When deposited onto a p‐type silicon substrate, the nanocomposites formed a heterojunction with rectifying behavior and pronounced photoresponse under illumination. Current–voltage measurements revealed an illumination‐induced shift of the photocurrent onset toward negative bias, suggesting photovoltaic activity. The photocurrent increased significantly with increasing illumination intensity, confirming the photoactive nature of the device. At a bias of 5 V and an illumination intensity of 240 mW cm −2 , the photodetector exhibited a responsivity of 0.16 A W −1 and a specific detectivity of ∼7.84 × 10 10 Jones. A comparative analysis with an undoped PEI N‐GQDs/p‐Si device fabricated under identical conditions was conducted to assess the effect of Bi incorporation. Furthermore, measurements conducted after 24 months showed that the heterojunction retained its electrical and photodetection characteristics, confirming its long‐term stability, highlighting its potential for sustainable and low‐complexity optoelectronic applications.