2 October 2025 in IEEE Sensors Journal
Power semiconductor devices generate mechanical stress wave (MSW) signals during switching processes, which can be used for condition monitoring (CM) of these devices with the advantages of noninvasive and non-destructive monitoring. Existing MSW signal detection methods are susceptible to electromagnetic interference and environmental factors (such as high temperature, high voltage, confined spaces, or structural constraints), which limit their adaptability in complex working conditions. Bare fiber Bragg grating (FBG) sensors offer strong resistance to electromagnetic interference and excellent environmental adaptability. Therefore, this paper proposes a transient high-frequency MSW measurement method for power semiconductor devices based on high-sample-rate bare FBG sensors. The MSW signals generated during the switching process of power semiconductor devices are successfully captured based on high-sample-rate bare FBG sensors for the first time. Comparative signal measurements between single-ended acoustic emission (AE) sensors and bare FBG sensors demonstrate the electromagnetic interference resistance capability of bare FBG sensors. Moreover, this study expands the application range of MSW detection methods for power semiconductor devices and provides new technical support for investigating the generation and propagation mechanisms of MSW signals.
22 January 2025 in IEEE Journal of Emerging and Selected Topics in Power Electronics
Effective condition monitoring (CM) technology ensures the safe operation of insulated gate bipolar transistors (IGBTs). Most CM methods for IGBTs focus on extracting electrical, thermal, and magnetic parameters. Recent studies indicate that at the switching moment, IGBTs can emit the switching stress wave (SSW) that is detectable by the acoustic emission (AE) sensors. However, using these SSWs to monitor the health status of IGBTs, even for discrete devices with relatively simple package structures, remains challenging. This paper investigates how SSWs from discrete IGBTs during power cycling change as bonding wires degrade and whether these waves are promising for monitoring the condition of internal bonding wires. In this work, a power cycle test platform and an SSW test platform for discrete IGBTs are built, and SSWs from discrete IGBTs during power cycling are analyzed. Results show that SSWs vary with the degradation of the device’s bonding wires, with changes in the time domain indicator of signal energy, reflecting SSW strength, and the frequency domain indicator of the center of gravity frequency, reflecting frequency shifts. These findings suggest the possibility for developing acoustic emission-based detection technology (AEDT) in CM of the IGBT.
21 December 2022 in IEEE Transactions on Instrumentation and Measurement
Condition monitoring technology plays an important role in ensuring the reliable operation of power semiconductor devices. Power semiconductor devices can generate stress waves when turned on and off, and the stress waves released by the device can be detected by the acoustic emission sensor. Acoustic emission detection technology has the characteristics of both non-destructive and real-time and is expected to be applied to the condition monitoring of power semiconductor devices in the future. However, temperature and electromagnetic fields can both affect the output characteristics of the acoustic emission sensor, which is not conducive to the application of acoustic emission detection technology. In addition, it is not clear how temperature affects the stress waves generated by power semiconductor devices. In this paper, a novel stress wave extraction method for power semiconductor devices is proposed, and the influence of temperature on the stress wave generated by IGBT at the turn-off moment is explored. Besides, a signal characteristic of the stress waves associated with the junction temperature of the device is extracted as the temperature-sensitive acoustic parameter, which will lay the foundation for the future research of new methods for online monitoring of junction temperature.
16 October 2024 in IEEE Transactions on Instrumentation and Measurement
Power semiconductor device condition monitoring technology based on the mechanical stress wave (MSW) is an important means to study device failure mechanisms and evaluate device reliability. However, MSW signals have mainly been detected through acoustic emission sensors for contact detection. The operating temperature of the device will affect the detection results, and the presence of MSW low-frequency components may be overlooked due to limitations in sensor performance. This paper proposes an offline, non-contact MSW measurement method based on laser Doppler vibrometer for power semiconductor devices. This method obtained the complete MSW signal generated during the switching process of power semiconductor devices, especially the low-frequency components below 20 kHz. Moreover, the proposed method exhibits greater sensitivity in detecting the high-frequency components of the MSW compared to the contact detection. This study extends the detection methods and frequency ranges for the MSW in power semiconductor devices, thereby expecting to facilitate the generation and propagation mechanisms research of the MSW.
17 October 2024 in IEEE Sensors Journal
Due to the effects of electromagnetic stress and thermoelastic effect, mechanical stress waves are generated in power semiconductor devices during turn-off moment. The characteristics of these turn-off stress waves vary when power semiconductor devices are subjected to different temperature environments. Measuring these turn-off stress waves is beneficial for analyzing the influence of temperature on the physical properties of power semiconductor devices. As a traditional contact-based mechanical stress wave detection method, acoustic emission testing (AET) is inevitably influenced by temperature, affecting the sensor’s measurement performance. This study employs non-contact laser Doppler vibrometry (LDV) to measure turn-off stress waves in silicon carbide metal-oxide-semiconductor field-effect transistor (SiC MOSFET) at different temperatures. By comparing the signals measured using AET, it has been demonstrated that the signals measured using LDV more effectively reflect the temperature-dependent variations in turn-off stress waves of SiC MOSFET. This research not only broadens the application scope of condition monitoring technology based on mechanical stress wave parameters for power semiconductor devices but also demonstrates the unique advantages of LDV in condition monitoring of power semiconductor devices in different temperature environments.
21 December 2023 in IEEE Transactions on Device and Materials Reliability
As a real-time, online, and non-invasive monitoring method, acoustic emission (AE) monitoring technology has a promising future in the condition monitoring and fault diagnosis of power devices such as power MOSFETs. Stress waves are generated when power MOSFETs are turned on and off. Currently, most scholars have only researched the influence of circuit parameters on stress waves in normal devices or the relationship between stress waves and the aging state of devices or modules. However, the correlation between the characteristics of the stress wave and the specific failures inside the device has not been determined. As a result, the experiment for gate-source overvoltage failure was carried out in this work. The differential acoustic emission sensor was used to acquire stress waves of power MOSFETs under different gate-source voltages, including stress waves during chip overvoltage failure. The characteristics of stress waves are analyzed from the perspectives of time-domain and frequency-domain, and it can be concluded that the time-domain peak-to-peak value, signal energy, and wavelet peak value of the stress wave during the failure process are significantly different from those under normal conditions. The experimental results laid the groundwork for making a connection between device failures and the characteristics of the stress wave, which indicates that it will be possible to apply the acoustic emission monitoring technology to the fault diagnosis of power devices in the future.