Muhammad Luqman Hakim

Muhammad Luqman Hakim

Auto-generated profile, based on publicly available information

Muhammad Luqman Hakim

Department of Naval Architecture, Faculty of Engineering, Universitas Diponegoro

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 October 2019 in IOP Conference Series: Earth and Environmental Science
Verified
Conference Paper
Open access
PDF file
MHM L Hakim
M L Hakim
BNB Nugroho
B Nugroho
MNM N Nurrohman
M N Nurrohman
ISI K Suastika
I K Suastika
I Ketut Aria Pria UtamaI Ketut Aria Pria Utama
I Ketut Aria Pria Utama
This article will look into to the environmental and economic issues in the maritime sector that arise due to biofouling. For the shipping industry, biofouling is known to increase hull roughness that would lead to an increase in friction resistance and fuel consumption. Here we present a short review regarding ship-hull roughness due to biofouling and its associated increase in skin friction drag, and analysis of fuel consumption from an operating ship with two different anti-fouling coating. The data shows that a higher quality antifouling would result in a low biofouling attachment on the hull surface, resulting in a lower fuel consumption.

28 January 2023 in Ocean Engineering
Verified
Journal Article
Closed access
MHM.L. Hakim
M.L. Hakim
ISI.K. Suastika
I.K. Suastika
IUI.K.A.P. Utama
I.K.A.P. Utama

21 April 2021 in Biofouling
Verified
Journal Article
Closed access
I Ketut Aria Pria UtamaI Ketut Aria Pria Utama
I Ketut Aria Pria Utama
BNBagus Nugroho
Bagus Nugroho
MYM. Yusuf
M. Yusuf
FPF. A. Prasetyo
F. A. Prasetyo
MHM. L. Hakim
M. L. Hakim
JMJason Monty
Jason Monty
Although the hull of a recently dry-docked large ship is expected to be relatively smooth, surface scanning and experimentation reveal that it can exhibit an “orange-peel” roughness pattern with an equivalent sand-grain roughness height ks = 0. 101 mm. Using the known ks value and integral boundary layer evolution, a recently cleaned and coated full-scale ship was predicted to experience a significant increase in the average coefficient of friction %ΔC¯f and total hydrodynamic resistance %ΔR¯T during operation. Here the report also discusses two recently reported empirical estimations that can estimate ks directly from measured surface topographical parameters, by-passing the need for experiments on replicated surfaces. The empirical estimations are found to have an accuracy of 4.5 − 5 percentage points in %ΔC¯f.

21 March 2024 in Ocean Engineering
Verified
Journal Article
Closed access
WAWilma Amiruddin
Wilma Amiruddin
MHMuhammad Luqman Hakim
Muhammad Luqman Hakim
AFAhmad Firdhaus
Ahmad Firdhaus
DPDian Purnamasari
Dian Purnamasari
TTTuswan Tuswan
Tuswan Tuswan
OMOcid Mursid
Ocid Mursid

25 March 2020 in CFD Letters
Verified
Journal Article
Open access
MHMuhammad Luqman Hakim
Muhammad Luqman Hakim
BNBagus Nugroho
Bagus Nugroho
RCRey Chin
Rey Chin
TPTeguh Putranto
Teguh Putranto
ISI Ketut Suastika
I Ketut Suastika
I Ketut Aria Pria UtamaI Ketut Aria Pria Utama
I Ketut Aria Pria Utama

1 September 2023 in Brodogradnja
Verified
Journal Article
Open access
PDF file
ATAndi Trimulyono
Andi Trimulyono
MHMuhammad Luqman Hakim
Muhammad Luqman Hakim
CAChairizal Ardhan
Chairizal Ardhan
SASyaiful Tambah Putra Ahmad
Syaiful Tambah Putra Ahmad
TTTuswan Tuswan
Tuswan Tuswan
ASAri Wibawa Budi Santosa
Ari Wibawa Budi Santosa
Along with developing high-speed craft technology, the planing hull is growing with modifications for better performance. One such technology is stepped hull, both single and double. Planing hull with steps allows the boat to run at a relatively low drag-lift ratio with lower frictional resistance due to reduced wetted area. In this study, the hull was modified with variations in the position of the double steps, which aimed to determine the effect of the first and second step positions on the total resistance, dynamic trim, and dynamic sinkage generated by computational fluid dynamics (CFD). Based on the analysis results, variations in the position of the stepped can change the hull performance. Shortening the distance between the two steps and moving both rearwards toward the transom can lower the total resistance. The dynamic trim and dynamic sinkage decreased as the position of the two steps was shifted further forward. An equation created in a non-dimensional form relates the positions of two steps to the desired results of total resistance, dynamic trim, and dynamic sinkage, namely: {(x1-x2)/L + (x1x2)/(LB)} × Fr∇, where x1 is distance the first step from transom, x2 is the distance of the second step, L is the length of the boat, B is the beam of the boat, and Fr∇ is the volume Froude number.