Ahmed Abuelnasr

Ahmed Abuelnasr

Auto-generated profile, based on publicly available information

Ahmed Abuelnasr

Department of Electrical Engineering, Polytechnique Montral, Montreal, QC, Canada

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
8 January 2024 in IEEE Access
Verified
Journal Article
Open access
MAMostafa Amer
Mostafa Amer
AAAhmed Abuelnasr
Ahmed Abuelnasr
Mohamed AliMohamed Ali
Mohamed Ali
Ahmad HassanAhmad Hassan
Ahmad Hassan
ATAref Trigui
Aref Trigui
YSYvon Savaria
Yvon Savaria
DC-DC buck converters in automotive and aerospace applications are often required to handle large disturbances in their input supply and abrupt variations in their loads. This paper proposes a systematic method to combine input-voltage feedforward (IVFF) and voltage-mode feedback (VFB) controllers, aiming to enhance the closed-loop performance of these DC-DC converters. This method relies on the stability boundary locus approach to help select the proper control parameters that achieve strong dynamic stability across the full operating range regardless of practical implementation challenges. Also, an optimization approach is employed to minimize the passive components’ area within the compensator, achieving a 79% reduction in integration size compared to conventional designs. The controller was fabricated in a 0.35- $\mu \text{m}$ CMOS technology, occupying a core area of 0.438 mm2. The prototype chip was experimentally tested to regulate a buck converter that leverages an e-GaN half-bridge while operating at 1 MHz. Measurement results show a remarkable closed-loop performance against line and load variations, reaching up to ±80 V/ms and ±535 mA per 150 $\mu \text{s}$ , respectively. The output remains stable, showcasing very small (<100 mV) to non-existent spikes and fast recovery periods. In addition, the system shows fast startup times ( $ < 100\mu \text{s}$ ) with small overshoots (<1%) observed at the output. The system power efficiency, tested across various loads, peaks at 95.14% while operating at 695 mA load current. It is shown that the combined-controller approach entirely eliminates transient voltage spikes, offering up to 100% improvement in dynamic performance over a standalone VFB controller.

1 May 2018
Verified
Conference Paper
Closed access
AAAhmed Abubakr
Ahmed Abubakr
AHAhmad Hassan
Ahmad Hassan
ARAhmed Ragab
Ahmed Ragab
SYSoumaya Yacout
Soumaya Yacout
YSYvon Savaria
Yvon Savaria
MSMohamad Sawan
Mohamad Sawan
We propose in this paper a high-temperature non-linear modeling for the I-V characteristics of GaN150 HEMT. Three different data-driven models were developed for a temperature range varying from 25°C to 250°C, by using three machine learning regression techniques namely: The Artificial Neural Network (ANN), the Support Vector Machine (SVM) and the Decision Tree (DT). Experiments were conducted on a GaN150 device with a width of 40 μm and accordingly, a set of measurements were obtained and exploited to build the device model. The three models were evaluated based on their ability to predict the I-V characteristics outside the temperature range (greater than 250°C) and their mean square error. The obtained results show that the models predict the device characteristics correctly based on the calculated mean squared error between the actual and predicted characteristics.

12 December 2023 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
MAMostafa Amer
Mostafa Amer
AAAhmed Abuelnasr
Ahmed Abuelnasr
Ahmad HassanAhmad Hassan
Ahmad Hassan
Ahmed RagabAhmed Ragab
Ahmed Ragab
Mohamad SawanMohamad Sawan
Mohamad Sawan
YSYvon Savaria
Yvon Savaria
The design of high-voltage (HV) switched-mode power systems (SMPSys) poses multiple challenges, such as minimizing the switching losses and preventing possible shoot-through currents, to achieve efficient and reliable operation. This article introduces a reconfigurable half-bridge gate driver (GD) for SMPSys, with an open-drain output configuration, electrostatic discharge self-protection, and two dead-time management modes to address these challenges. The first mode is an externally tunable fixed dead-time generator (FDTG) capable of achieving a wide dead-time range from 5 to 200 ns. The second mode is a self-adjusting dead-time generator (SDTG), designed to adapt to delay mismatches between the GD's channels, regardless of process, voltage, and temperature (PVT) variations, while minimizing dead-time and preventing cross-conduction. The GD was fabricated in an HV 0.18-μm silicon-on-insulator CMOS process technology, supporting a high-side floating bias voltage rail up to 100 V and occupying a core area of 0.285 mm 2 . It was tested in a buck converter system using a gallium nitride (GaN)-based half-bridge with a switching frequency of 0.5 to 1 MHz. It achieves a total propagation delay of 11.4 ns and a minimum dead-time of 3.6 ns (3× smaller than state-of-the-art) using its SDTG mode. The system achieved a peak efficiency of 90.5% at an output load of 8 W. Notably, the SDTG mode improves the overall efficiency by up to 20% over the FDTG mode, specifically at higher switching frequencies, showing its effectiveness in enhancing the performance of SMPSys.

6 January 2023 in IEEE Transactions on Circuits and Systems I: Regular Papers
Verified
Journal Article
Closed access
AAAhmed Abuelnasr
Ahmed Abuelnasr
MAMostafa Amer
Mostafa Amer
Mohamed AliMohamed Ali
Mohamed Ali
Ahmad HassanAhmad Hassan
Ahmad Hassan
Benoit GosselinBenoit Gosselin
Benoit Gosselin
YSYvon Savaria
Yvon Savaria
The Design of efficient, safe, and reliable circuits is a prime objective in high-voltage (HV) electronic systems, such as switched-mode power amplifiers (PAs). One of the main causes of efficiency degradation and reliability problems, in these amplifiers, is the shoot-through current from the HV power supply to the ground. To eliminate such current, a dead time generator (DTG) is used to modify the signals propagating through the high-side and low-side gate drivers by adding a fixed dead time between them. However, any delay mismatch between these gate drivers can reduce the dead time to the point that it becomes negative. In this paper, an HV-DTG architecture is introduced. The architecture mitigates the effects of delay mismatch variations in gate drivers, which can result from parameters mismatch, fabrication process variations, and temperature variations. An HV switched-mode class-D power amplifier is used to illustrate the performance of the DTG. The amplifier is implemented in a low-cost 0.35 $\mu$ $m$ HV CMOS process. The total area of the PA is 0.5 $mm^2$ , where the DTG covers an area of 0.066 $mm^2$ . A measured system’s efficiency of 95.14% is achieved with the shortest dead time of 10.8 ns, which is 1.38x smaller than the generated dead time in comparable state-of-the-art HV dead time generators.

30 January 2024 in Engineering Applications of Artificial Intelligence
Verified
Journal Article
Closed access
AAAhmed Abuelnasr
Ahmed Abuelnasr
Ahmed RagabAhmed Ragab
Ahmed Ragab
MAMostafa Amer
Mostafa Amer
Benoit GosselinBenoit Gosselin
Benoit Gosselin
YSYvon Savaria
Yvon Savaria

1 September 2017
Verified
Conference Paper
Closed access
AAAhmed Abubakr
Ahmed Abubakr
AIAhmed Ibrahim
Ahmed Ibrahim
YIYehea Ismail
Yehea Ismail
Hassan MostafaHassan Mostafa
Hassan Mostafa
Memristors are novel devices that are used to replace SRAMs as memory arrays in the near future. Therefore, this work investigates the impact of radiation on memristor-based memory. Moreover, this work aims at calculating the critical charge that causes soft errors due to an alpha particle or a neutron strike in HP memristor using analytical models. These models are verified by using Cadence Spectre simulations. The TEAM model is utilized in the model derivation and verification. Studying the impact of radiation on memristors is very essential in the migration step from SRAM memories to memristor-based memories. This work will help memristor-based memory arrays designers predict the impact of soft errors on their memory design and find methods to mitigate these soft errors.