DC-DC buck converters in automotive and aerospace applications are often required to handle large disturbances in their input supply and abrupt variations in their loads. This paper proposes a systematic method to combine input-voltage feedforward (IVFF) and voltage-mode feedback (VFB) controllers, aiming to enhance the closed-loop performance of these DC-DC converters. This method relies on the stability boundary locus approach to help select the proper control parameters that achieve strong dynamic stability across the full operating range regardless of practical implementation challenges. Also, an optimization approach is employed to minimize the passive components’ area within the compensator, achieving a 79% reduction in integration size compared to conventional designs. The controller was fabricated in a 0.35- $\mu \text{m}$ CMOS technology, occupying a core area of 0.438 mm2. The prototype chip was experimentally tested to regulate a buck converter that leverages an e-GaN half-bridge while operating at 1 MHz. Measurement results show a remarkable closed-loop performance against line and load variations, reaching up to ±80 V/ms and ±535 mA per 150 $\mu \text{s}$ , respectively. The output remains stable, showcasing very small (<100 mV) to non-existent spikes and fast recovery periods. In addition, the system shows fast startup times ( $ < 100\mu \text{s}$ ) with small overshoots (<1%) observed at the output. The system power efficiency, tested across various loads, peaks at 95.14% while operating at 695 mA load current. It is shown that the combined-controller approach entirely eliminates transient voltage spikes, offering up to 100% improvement in dynamic performance over a standalone VFB controller.
12 December 2023 in IEEE Transactions on Power Electronics
The design of high-voltage (HV) switched-mode power systems (SMPSys) poses multiple challenges, such as minimizing the switching losses and preventing possible shoot-through currents, to achieve efficient and reliable operation. This article introduces a reconfigurable half-bridge gate driver (GD) for SMPSys, with an open-drain output configuration, electrostatic discharge self-protection, and two dead-time management modes to address these challenges. The first mode is an externally tunable fixed dead-time generator (FDTG) capable of achieving a wide dead-time range from 5 to 200 ns. The second mode is a self-adjusting dead-time generator (SDTG), designed to adapt to delay mismatches between the GD's channels, regardless of process, voltage, and temperature (PVT) variations, while minimizing dead-time and preventing cross-conduction. The GD was fabricated in an HV 0.18-μm silicon-on-insulator CMOS process technology, supporting a high-side floating bias voltage rail up to 100 V and occupying a core area of 0.285 mm 2 . It was tested in a buck converter system using a gallium nitride (GaN)-based half-bridge with a switching frequency of 0.5 to 1 MHz. It achieves a total propagation delay of 11.4 ns and a minimum dead-time of 3.6 ns (3× smaller than state-of-the-art) using its SDTG mode. The system achieved a peak efficiency of 90.5% at an output load of 8 W. Notably, the SDTG mode improves the overall efficiency by up to 20% over the FDTG mode, specifically at higher switching frequencies, showing its effectiveness in enhancing the performance of SMPSys.
6 January 2023 in IEEE Transactions on Circuits and Systems I: Regular Papers
The Design of efficient, safe, and reliable circuits is a prime objective in high-voltage (HV) electronic systems, such as switched-mode power amplifiers (PAs). One of the main causes of efficiency degradation and reliability problems, in these amplifiers, is the shoot-through current from the HV power supply to the ground. To eliminate such current, a dead time generator (DTG) is used to modify the signals propagating through the high-side and low-side gate drivers by adding a fixed dead time between them. However, any delay mismatch between these gate drivers can reduce the dead time to the point that it becomes negative. In this paper, an HV-DTG architecture is introduced. The architecture mitigates the effects of delay mismatch variations in gate drivers, which can result from parameters mismatch, fabrication process variations, and temperature variations. An HV switched-mode class-D power amplifier is used to illustrate the performance of the DTG. The amplifier is implemented in a low-cost 0.35 $\mu$$m$ HV CMOS process. The total area of the PA is 0.5 $mm^2$ , where the DTG covers an area of 0.066 $mm^2$ . A measured system’s efficiency of 95.14% is achieved with the shortest dead time of 10.8 ns, which is 1.38x smaller than the generated dead time in comparable state-of-the-art HV dead time generators.
This paper details the development and validation of a temperature sensing methodology using an un-trimmed oscillator-based integrated sensor implemented in the 0.18-m SOI XFAB process, with a focus on thermal monitoring in system-on-chip (SoC) based DC-DC converters. Our study identifies a quadratic relationship between the oscillator output frequency and temperature, which forms the basis of our proposed calibration mechanism. This mechanism aims at mitigating process variation effects, enabling accurate temperature-to-frequency mapping. Our research proposes and characterizes several trimming-free calibration techniques, covering a spectrum from zero to thirty-one frequency-temperature measurement points. Notably, the Corrected One-Point calibration method, requiring only a single ambient temperature measurement, emerges as a practical solution that removes the need for a temperature chamber. This method, after adjustment, successfully reduces the maximum error to within °C. Additionally, the Two-Point calibration method demonstrates improved precision with a maximum positive error of +1.56 °C at −15 °C and a maximum negative error of −3.13 °C at +10 °C ( value of 0.9958). The Three-Point calibration method performed similarly, yielding an value of 0.9956. The findings of this study indicate that competitive results in temperature sensor calibration can be achieved without circuit trimming, offering a viable alternative or a complementary approach to traditional trimming techniques.
30 January 2024 in Engineering Applications of Artificial Intelligence
This paper contributes toward the implementation of Gallium Nitride (GaN)-based integrated circuits (ICs) intended for high-temperature (HT) applications. We present the implementation and HT characterization of epitaxial AlGaN/GaN Heterojunction Field Effect Transistors (HFETs). The AlGaN/GaN HFETs are remarkably stable enabling operation above 600°C. The characterization results are used to extract an extended version of the Angelov model of GaN HFETs after considering the temperature as a variable parameter. A MATLAB program is used to fit the developed model with experimental I- V characteristics and a R-squared regression of 0.998 was attained over a wide temperature range extending from 25°C to 500°C. The extracted model is intended to be included in a design kit capturing the temperature effects and enabling accurate design simulations.