14 July 2018 in Journal of the Electrochemical Society
Lithium plating leads to severe capacity fading and possible safety problems in lithium-ion batteries. Thus, non-destructive detection methods for lithium plating are critical for safe and reliable operation of lithium-ion batteries. In this paper, an electrochemical model incorporated with lithium plating and stripping reactions is established to investigate the lithium plating-stripping process at low temperature. The model is validated at different current rates and temperatures and can successfully predict the characteristic voltage plateau during the rest period after low temperature charging. Modeling analysis helps to develop detection method for lithium plating via differential analysis on the voltage plateau. Distinct local minima can be found in the differential voltage curves of the batteries with plated lithium. The time when the local minima occurs in the differential voltage curves exhibits a linear relationship with the amount of reversible lithium, and thus can be applied as a quantitative indicator for detection of lithium plating. The detection of lithium plating based on differential voltage analysis is further extended to the discharge voltage profiles of the batteries after low temperature charging, considering the effects of rest time.
29 April 2019 in Journal of the Electrochemical Society
To improve electric vehicle market acceptance, the charge time of their batteries should be reduced to 10–15 minutes. However, achieving 4C to 6C charge rates with today's batteries is only possible for cells with thin electrodes coming at the expense of low energy density and high battery manufacturing cost. An electrochemical model is validated versus high rate charge data for cells with several loadings. The model elucidates that the main limitations for high energy density cells are poor electrolyte transport resulting in salt depletion within the anode and Li plating at the graphite/separator interface. Next, the model is used to understand what future electrode and electrolyte properties can help enable 4C and 6C charging. Ideally, future electrolytes would be identified with 2X conductivity, 3–4X diffusivity, and transference number of 0.5–0.6. Alternatively charging at elevated temperatures enhances electrolyte transport by 1.5X conductivity and 2–3X diffusivity with a negligible effect on transference number. Another effective strategy to enable 4C and 6C charging is reducing electrode tortuosity. Conversely, increasing electrode porosity and negative/positive ratio are ineffective strategies to improve fast charge capability.
8 July 2020 in Energy & Environmental Science
The principal inhibitor of fast charging lithium ion cells is the graphite negative electrode, where favorable conditions for lithium plating occur at high charge rates, causing accelerated degradation and safety concerns. The local response of graphite, both at the electrode and particle level, when exposed to fast charging conditions of around 6C is not well understood. Consequently, the conditions that lead to the onset of lithium plating, as well as the local dynamics of lithium plating and stripping, have also remained elusive. Here, we use high-speed (100 Hz) pencil-beam X-ray diffraction to repeatedly raster along the depth of a 101 μm thick graphite electrode in 3 μm steps during fast (up to 6C) charge and discharge conditions. Consecutive depth profiles from separator to current collector were each captured in 0.5 seconds, giving an unprecedented spatial and temporal description of the state of the electrode and graphite's staging dynamics during high rate conditions. The electrode is preferentially activated near the separator, and the non-uniformity increases with rate and is influenced by free-energy barriers between graphite's lithiation stages. The onset of lithium plating and stripping was quantified, occurring only within the first 15 μm from the separator. The presence of lithium plating changed the behavior of the underlying graphite, such as causing co-existence of LiC6 and graphite in the fully discharged state. Finally, the staging behavior of graphite at different rates was quantified, revealing a high dependency on rate and drastic hysteresis between lithiation and delithiation.
17 January 2023 in Nature Communications
The energy transition will require a rapid deployment of renewable energy (RE) and electric vehicles (EVs) where other transit modes are unavailable. EV batteries could complement RE generation by providing short-term grid services. However, estimating the market opportunity requires an understanding of many socio-technical parameters and constraints. We quantify the global EV battery capacity available for grid storage using an integrated model incorporating future EV battery deployment, battery degradation, and market participation. We include both in-use and end-of-vehicle-life use phases and find a technical capacity of 32–62 terawatt-hours by 2050. Low participation rates of 12%–43% are needed to provide short-term grid storage demand globally. Participation rates fall below 10% if half of EV batteries at end-of-vehicle-life are used as stationary storage. Short-term grid storage demand could be met as early as 2030 across most regions. Our estimates are generally conservative and offer a lower bound of future opportunities.
2 November 2018 in Journal of the Electrochemical Society
KCKoffi Pierre Yao Claver
+7
Battery performance is strongly correlated with electrode microstructural properties. Of the relevant properties, the tortuosity factor of the electrolyte transport paths through microstructure pores is important as it limits battery maximum charge/discharge rate, particularly for energy-dense thick electrodes. Tortuosity factor however, is difficult to precisely measure, and thus its estimation has been debated frequently in the literature. Herein, three independent approaches have been applied to quantify the tortuosity factor of lithium-ion battery electrodes. The first approach is a microstructure model based on three-dimensional geometries from X-ray computed tomography (CT) and stochastic reconstructions enhanced with computationally generated carbon/binder domain (CBD), as CT is often unable to resolve the CBD. The second approach uses a macro-homogeneous model to fit electrochemical data at several rates, providing a separate estimation of the tortuosity factor. The third approach experimentally measures tortuosity factor via symmetric cells employing a blocking electrolyte. Comparisons have been made across the three approaches for 14 graphite and nickel-manganese-cobalt oxide electrodes. Analysis suggests that if the tortuosity factor were characterized based on the active material skeleton only, the actual tortuosities would be 1.35–1.81 times higher for calendered electrodes. Correlations are provided for varying porosity, CBD phase interfacial arrangement and solid particle morphology.
7 October 2017 in Journal of the Electrochemical Society
SSShriram Santhanagopalan
Galvanostatic intermittent titration technique (GITT) – a popular method for characterizing kinetic and transport properties of battery electrodes – is predicated on the proper evaluation of electrode active area. LiNi0.5044Co0.1986Mn0.2970O2 (NCM523) material exhibits a complex morphology in which sub-micron primary particles aggregate to form secondary particle agglomerates. This work proposes a new active area formulation for primary/secondary particle agglomerate materials to better mimic the morphology of NCM532 electrodes. This formulation is then coupled with macro-homogeneous models to simulate GITT and half-cell performance of NCM523 electrodes. Subsequently, the model results are compared against the experimental results to refine the area formulation. A single parameter, the surface roughness factor, is proposed to mimic the change in interfacial area, diffusivity and exchange current density simultaneously and detailed modeling results are presented to provide valuable insights into the efficacy of the formulation.