In this work, we present a wireless energy-efficient fully integrated amplitude shift keying (ASK) transmitter (TX) array at 220 GHz. Each TX cell consists of an oscillator, a modulation switch, an on-chip antenna, and baseband amplifiers. The oscillator uses a harmonic generation technique that is optimized for maximum output power and efficiency. The ASK scheme is used for data modulation and is implemented with a fast switch that does not consume any dc power. Three of these TX cells are coherently coupled together to increase the signal-to-noise ratio (SNR) and, hence, the data rate. This also enables the possibility of having a four-level spatial ASK modulation. Fabricated in a 55-nm SiGe bipolar complementary metal oxide semiconductor (BiCMOS) process, the array dissipates 165.2 mW of dc power and generates 4.2-dBm effective isotropic radiated power (EIRP). The chip demonstrates a 20-Gb/s data transmission rate with on-off keying (OOK) modulation at a 28-cm distance using low-cost Teflon lenses. The measured energy efficiency of the array is 8.26 pJ/bit. To the best of our knowledge, this work demonstrates the best energy efficiency among TX arrays at this frequency range.
18 June 2021 in IEEE Transactions on Circuits and Systems I: Regular Papers
This paper presents a transimpedance-to-noise optimization approach for design of a resistive shunt-feedback TIA. This optimization offers an enhancement in the transimpedance and a noise performance very close to the theoretical minimum noise of the TIA. In addition, the transimpedance-to-noise optimization approach results in a small front-end FET size which enables a further reduction in power and area. Moreover, this approach enables using a fewer number of stages in the receiver chain which makes a high PSRR feasible and obviates the necessity for using an offset cancellation circuitry. Building on this approach, a fully differential analog front-end including a resistive shunt-feedback TIA and a post amplifier (PA) for time-of-flight (ToF) Lidar receivers is designed and implemented, achieving 94dB Ω transimpedance gain, 71nA input-referred rms noise current, -3dB bandwidth of 340MHz, and power supply rejection ratio (PSRR) of more than 87dB in a 0.11 μm CMOS process. The associated DC power consumption is 19.4mW with V DD of 1.8V. Moreover, a push-pull buffer with 1V output swing is integrated for driving 50 Ω loads, such as off-chip time discriminators, which also additionally amplifies the signal with a gain of 5dB while consuming an extra 20.9mW of DC power. The whole chip (excluding pads) occupies 210 μm × 110 μm in area.
20 August 2020 in IEEE Solid-State Circuits Letters
In this paper, a low cost, compact, and systematic method for generating a short pulse and efficiently delivering it to low impedance loads is proposed. The load can be a resistive on-chip or off-chip load, an antenna, or another stage such as a power combiner. The technique is inspired by time domain reflectometry from a short-circuited termination. The technique is fully compatible with CMOS technology. To show the feasibility of the idea, two chips are fabricated and tested in a low cost 0.11 μm CMOS process with fT≈80GHz. The full width at half maximum (FWHM) of the pulses are 6.8 ps and 8.8 ps, and the amplitudes over a 50 Ω load are 0.62 V and 1 V. Either of the chips occupies 1160×540 μm2 in area.
17 October 2023 in IEEE Journal of Solid-State Circuits
This article first analytically compares the energy efficiency of a serial optical link with a parallel link with the same data throughput and bit error rate for interchip communication. The analysis predicts that more than $10\times $ energy efficiency improvement is feasible at both TX and RX in a parallel optical link compared to the fastest serial link, depending on the technology. Next, the article presents the design of an optical receiver integrated with on-chip blue photodetectors for the parallel interchip communication. The blue light allows using high-speed microLEDs and enables CMOS compatible photodetector structures that have extremely low capacitance per unit area. This along with a transimpedance-to-noise optimization approach results in a highly energy efficient and compact analog front-end for the receiver, paving the way for dense and energy efficient parallel links. Besides, a digital offset cancellation technique is proposed for offset compensation that can provide a low-end cutoff frequency down to a few hertz with a compact area. As a proof of concept, a 32 elements optical receiver array is fabricated in a low-cost 130 nm CMOS SOI process, with each element occupying only 50 $\times $ 50 $\mu \text{m}$ in area. Free space optical measurement results of a single receiver array element show a sensitivity of −19.3 dBm with a bit error rate of 10−12 at a data rate of 2 Gbps and an energy efficiency of about 0.5 pJ/bit.
Various approaches are being considered to address the demand for high-throughput (Gb/s) point-to-point wireless communication systems in 5G infrastructure and sub-THz transceivers. Two fully integrated CMOS wireless transmitters with frequency shift keying (FSK) modulation were prototyped in a standard 55 nm SiGe process. Benefiting from the coupled oscillator loop system, the single channel data rate up to 10 Gb/s wireless link (limited by measurement equipment) was demonstrated. The proposed coupled oscillator loop system enables instantaneous frequency shift in an ideal situation, which resolves overshoots/undershoots and long frequency settling issues in the conventional varactor-based LC voltage controlled oscillator. The measured single channel data rate is around 5× higher than the previously published CMOS/BiCMOS FSK transmitter.