Orthodontic is one of the treatments in dentistry field which concerned on malocclusion treatments such as improper bites, tooth irregularity and disproportionate jaw relationships. The mini-implant (OMI) is one of the components used in the orthodontic treatment, besides braces and spring. The application of OMI has been well accepted in orthodontic treatment. However, one of the main factors of OMI failures is the implant insertion procedure in which the clinician find it difficult to obtain the best angle to insert the OMI. Therefore, this study aims to evaluate stress in an OMI and bones using the finite element analysis (FEA) with variations of insertion angles and to identify their optimal angle for the implant placement. The three dimensional (3D) model of a left maxillary posterior bone section was constructed based on CT image dataset. That 3D model consists of cortical bone, cancellous bone, second premolar, first molar and second molar teeth. The 3D model of OMI was placed between root of second premolar and first molar teeth. The OMI was simulated with seven different angles of insertions: 30˚, 40˚, 50˚, 60˚, 70˚, 80˚ and 90˚. Within the seven different insertion angles, the results showed that the increase of insertion angle reduced the maximum equivalent von Mises stress in cortical bone, cancellous bone and OMI. Based on this FEA study, the optimal angle placement of OMI is when the implant positioned at vertical angle (90˚) to the bone surface.
The high sensitivity of Lorentz sensors comes from its narrowband resonant characteristics marked by rapid slope change of slope of its phase spectrum, a phenomenon known as Anomalous dispersion. Unlike conventional microwave resonant sensors which have a resonant amplitude, the Lorentz sensors also have unique signature in its phase spectra which adds a second degrees of freedom in detection and removes ambiguity in the identification of the resonant frequency. We demonstrate two sensing applications in which ultra-high sensitivity is required. In particular, we show that by exploiting the high electric field regions in Lorentz resonators detection of low density gaseous water states (steam) and sub-wavelength sized biomaterials is possible. The material sensing is performed by characterizing the resonant shifts in the frequency range of 1 to 2 GHz. Depending on the gaseous state concentrations, the dielectric constant of the detected steam lies between 1.04 and 1.6 GHz. The Lorentz resonator is shown to distinguish accurately between different sub-wavelength samples derived from different parts of chicken. We anticipate that the proposed sensor can be used in biosensing of cancerous cells and in detecting low-permittivity poisonous gaseous matter such as clear smoke, carbon mono oxide, methane and nitrogen.
30 November 2024 in Journal of Advanced Research in Applied Mechanics
Storage and preservation of articular cartilage are important in experimental studies. Various storage temperatures were used which led to conflicting results on the biomechanical properties of the cartilage. Therefore, this study aimed to examine the effect of storage temperature on the magnetic resonance imaging (MRI) image and biomechanical properties of articular cartilage. The cartilage specimens were extracted from hip bovine joints which were then tested in fresh condition and in a single freeze-thaw cycle at -20°C to observe the effect of the temperature. Low-field MRI was utilized to obtain the images which were processed to determine the greyscale intensity of the cartilage. Subsequently, indentation tests were conducted on the cartilage and the data was integrated with finite element analysis to characterize the biomechanical properties of permeability and elastic modulus. Based on the results, the elastic modulus of the frozen cartilage decreased to 29%, while the permeability increased to 77% compared to the fresh cartilage. Furthermore, a strong positive correlation (r=0.85) was found between MRI image greyscale and permeability, while a negative moderate correlation (r=-0.51) was obtained between MRI image greyscale and elastic modulus. These findings highlighted the significant effect of storage temperature on the MRI image greyscale and biomechanical properties of cartilage.
The present study reports the anisotropy effects of uniaxial and multiaxial loading on cancellous bone in order to mimic true physiological conditions as well as pathological reactions and thereby provides improved data that represents clinical and real life conditions. Cancellous bone samples were CT-scanned for morphological analysis and model construction. The models were then computationally loaded on three different directions; horizontal, vertical, and at 45°. Lower BV/TV, Tb.Th, and Conn.D resulted in lower number of cycles to failure, regardless to the loading conditions. However, the number of cycles to failure was found to be negatively correlated to the value of structural model index. Dramatic increased in effective plastic strain and decrease in cycles to failure were demonstrated by the cancellous bone models under multiaxial loading. The reduction of fatigue life was five times lower in multiaxial condition in comparison to the fatigue life under uniaxial loading. Off-axis orientation effect on the fatigue life of the trabecular bone was demonstrated the worst in horizontal trabecular bone model. Effective plastic strain was recorded the highest in horizontal model, while the model at 45° demonstrated 1.6 times higher effective plastic strain than the vertical ones. This is due to several numbers of thin trabeculae which are susceptible to fatigue at higher stress concentration. In conclusion, the anisotropic effect of uniaxial and multiaxial loading onto the mechanical behaviour of bovine cancellous bone was demonstrated throughout this study. It is apparent that multiaxial with off-axis forces are important to be considered as the loading direction manifests the fatigue lifetime of cancellous bone.