Riikka Mikkonen

Riikka Mikkonen

Auto-generated profile, based on publicly available information

Riikka Mikkonen

Faculty of Information Technology and Communication Sciences, Tampere University, Tampere, Finland

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 February 2020 in ACS Applied Materials & Interfaces
Verified
Journal Article
Open access
RMRiikka Mikkonen
Riikka Mikkonen
PPPaula Puistola
Paula Puistola
IJIlari Jönkkäri
Ilari Jönkkäri
MMMatti Mäntysalo
Matti Mäntysalo
In recent years, additive manufacturing of polydimethylsiloxane (PDMS) has gained interest for the development of soft electronics. To fabricate complex electrical devices, fabrication of multilayered structures is required. We propose here a straightforward digital printing fabrication process of silicone rubber-based, multilayered electronics. An inkjet-printable PDMS solution was developed for digital patterning of elastomeric structures. The silicone ink was used together with a highly conductive silver nanoparticle (Ag np) ink for the fabrication of the all-inkjet printed and multilayered electrical devices. The application of the multilayer circuit board was successful. The sheet resistances were below 0.3 Ω/□, with a conductive layer thickness less than 1 µm. The electrical insulation between the conductive layers was done by printing 20-25 µm thick dielectric PDMS layer selectively on top of the bottommost conductive layer.

31 May 2021 in IEEE Sensors Journal
Verified
Journal Article
Open access
RMRiikka Mikkonen
Riikka Mikkonen
AKAnastasia Koivikko
Anastasia Koivikko
TVTiina Vuorinen
Tiina Vuorinen
Veikko SariolaVeikko Sariola
Veikko Sariola
MMMatti Mäntysalo
Matti Mäntysalo
The development of soft electronics is critical to the realization of artificial intelligence that comes into direct contact with humans, such as wearable devices, and robotics. Furthermore, rapid prototyping and inexpensive processes are essential for the development of these applications. We demonstrate here an additive, low-cost method for fabricating polydimethylsiloxane based soft electronics by inkjet printing. Herein, a novel approach using a water-soluble polyvinyl alcohol layer as the substrate, inexpensive, fully digital fabrication of capacitive pressure sensors is enabled by sandwiching mesh-like conductive layers and microstructured dielectric in a straightforward, convenient manner. These sensors exhibit improved sensitivity (4 MPa −1 ) at low pressures (< 1 kPa) in contrast to sensors with a flat elastomer dielectric and can still detect large pressures around 50 kPa, having excellent long-term repeatability over 2000 cycles, without significant hysteresis (≤ 8.5 %). The tactile sensing ability of the fabricated devices was demonstrated in a practical application. Moreover, sensor characteristics are easily adjustable, simply by changing printing parameters or tuning the ink solution. The proposed approach provides scalable solution for fabricating high-sensitivity printed sensors for e-skin and human-machine interfaces.

1 July 2018 in Microelectronics Reliability
Verified
Journal Article
Closed access
RMRiikka Mikkonen
Riikka Mikkonen
MMMatti Mäntysalo
Matti Mäntysalo

1 June 2018
Verified
Conference Paper
Closed access
RMRiikka Mikkonen
Riikka Mikkonen
SLSanna Lahokallio
Sanna Lahokallio
LFLaura Frisk
Laura Frisk
MMMatti Mantysalo
Matti Mantysalo

1 September 2017
Verified
Conference Paper
Closed access
RMRiikka Mikkonen
Riikka Mikkonen
MMMatti Mantysalo
Matti Mantysalo