25 June 2019 in IEEE Journal of Solid-State Circuits
18 November 2019 in IEEE Transactions on Biomedical Circuits and Systems
This paper proposed a wearable smart sEMG recorder integrated gradient boosting decision tree (GBDT) based hand gesture recognition. A hydrogen-silica gel based flexible surface electrode band is used as the tissue interface. The sEMG signal is collected using a neural signal acquisition analog front end (AFE) chip. A quantitative analysis method is proposed to balance the algorithm complexity and recognition accuracy. A parallel GBDT implementation is proposed featuring a low latency. The proposed GBDT based neural signal processing unit (NSPU) is implemented on an FPGA near the AFE. A RF module is used for wireless communication. A hand gesture set including 12 gestures is designed for human-computer interaction. Experimental results show an overall hand gesture recognition accuracy of 91%.
17 November 2020 in IEEE Transactions on Biomedical Circuits and Systems
A bio-potential recorder working under 0.8 V supply voltage with a tunable low-pass filter is proposed in this paper. The prototype is implemented in TSMC 180 nm CMOS technology, featuring a power consumption of 2.27 μW, while preserving a high tolerance of power-line interference (PLI) up to 600 mVpp, a common-mode rejection ratio (CMRR) of higher than 100 dB, a THD of -65.5 dB, and a noise density of 50nV/ ${\sqrt{Hz}}$ by employing four new techniques, including 1) low noise chopper modulator, 2) feedback loop based common-mode cancellation loop (CMCL), 3) offset cancellation loop (OCL) with PMOS backgate control scheme, and 4) a very-lower transconductance (VLT) operational transconductance amplifier (OTA) using in the DC-servo-loop (DSL). The measured mid-band gain is 43.3 dB with a high-pass cut-off frequency of 1.2 Hz. The low-pass cut-off frequency can be configured from 650 Hz to 7.5 kHz. The measured inputreferred integrated noise is 1.2 uVrms in the frequency band of 1-650 Hz and 4.1 uVrms in the 1 Hz-7.5 kHz frequency band, respectively, leading to a power efficiency factor (PEF) of 7.49 and 7.59.
16 October 2023 in IEEE Transactions on Power Electronics
In order to suppress the crosstalk in GaN based bridge configuration, this paper proposes a novel high frequency three-level gate driver (HFTGD), and the crosstalk suppression with switching frequency up to 5 MHz can be achieved. The capacitor-diode (C-D) circuit generates a negative voltage to prevent the false turn-on of the device under the impact of positive crosstalk. PWM generator work together with comparator circuit to rapidly clamps the negative voltage to zero level, thereby suppressing the negative crosstalk. In particular, HFTGD utilizes only two passive components to produce the negative voltage, and also has the advantages of good high frequency stability and adjustable negative voltage depth. The control signal of the zero-level clamp circuit is digitally implemented, resulting in a shorter clamp time and minimal impact on the switching speed of the GaN HEMT. Additionally, only a single power supply and a single control signal are required for HFTGD, which reduces the cost and control complexity. The effectiveness of HFTGD for positive and negative crosstalk suppression is demonstrated in a double-pulse test based on GS66504B
26 March 2024 in IEEE Transactions on Nuclear Science
Bandgap is a critical block for numerous electronic systems, which provides stable voltage reference for multiple sub-modules over process, voltage supply, and temperature (PVT) fluctuations. This paper firstly proposes a radiation-hardened-by-design (RHBD) technique which can automatically detect single-event transient (SET) disturbances and convert them into nanosecond-scale alternating signals, which can then be easily filtered by an on-chip filter. Theoretically, this technique can reduce SET amplitude to a negligible level regardless of bandgap structure and the output DC voltage. Laser experiments indicate that the SET pulse amplitude can be reduced from 896 mV to 48 mV under 800 pJ laser strike. This technique provides new guidance for SET mitigation on constant DC voltage and is widely applicable for bandgap radiation-hardening design.