Electric vehicle charging platforms in the market are usually rated as 400 or 800 V, so the wireless charging system of electric vehicles must effectively supply power for these two voltage platforms. It is also an urgent problem to keep the output stable in the case of misalignment. The antioffset wireless charging system based on the reconfigurable coupling coupler is proposed. A coupling structure is reconfigured by a switch to charge a 400- or 800-V charging platform at the same power level. Simultaneously, an additional set of quadrupole receiving coils is connected in series to compensate for the reduced mutual inductance when offset occurs. To verify the proposed wireless power transfer system, a scaled-down experimental prototype was built. The results show that the highest dc–dc efficiency of the system is 93.66% and 94.27% at the voltage level of 200 and 400 V, respectively, and has good misalignment tolerance in two perpendicular directions.
16 May 2025 in IEEE Transactions on Power Electronics
Improving power density and system integration is a pivotal focus for wireless power transfer (WPT) in portable devices. However, challenges, such as misalignment tolerance and power fluctuation persist. This letter introduces a robust solution utilizing secondary independent PWM control. A coil structure combining solenoids and reverse windings ensures passive misalignment tolerance, while a grooved magnetic core integrates the converter, optimizing compactness. In addition, the secondary PWM control achieves precise output voltage regulation without communication. A high-power-density WPT prototype validates the proposed coupler and control method, demonstrating less than 1% output voltage fluctuation under a 50% misalignment and maintaining over 89% efficiency at 100 W. The secondary device is highly compact, measuring only 60 mm × 30 mm × 7.5 mm and achieving power density of 7.41 W/cm3.
23 December 2019 in IEEE Transactions on Power Electronics
This paper studies the modeling of high-bandwidth buck converters under constant-frequency voltage-mode (CFVM) control, where the traditional small-signal averaged model fails due to two major factors in the pulse width modulation (PWM), i.e. the large harmonics of modulation waveform and the considerable sideband components. Several modified small-signal models have been proposed to improve the predictions of the frequency domain characteristics. However, these models are less generalization or with high complexity, and may hardly be used in the closed-loop design of real applications. To handle this issue, this paper proposes a generalized multi-frequency small-signal model (G-MFSSM) for high-bandwidth buck converters, which makes further progress in accuracy while maintaining simplicity in deriving the analytical transfer functions for a closed-loop design. The generalized average model (GAM) is adopted to precisely describe the first-order harmonic of the modulation waveform, from which a correction factor is extracted to evaluate the influence of the ripple. Furthermore, two dominant sideband components are selected optimally for extremely accurate loop gain predictions. Finally, a closed-loop design procedure is presented for wide-input high-bandwidth buck converters based on the proposed G-MFSSM. The validity of the proposed G-MFSSM is verified by simulations and experiments.
22 January 2025 in IEEE Transactions on Power Electronics
In the application process of wireless charging for electric vehicles, foreign object detection (FOD) is one of the necessary measures to address safety issues. This letter proposes a self-resonant FOD method for metal object (MO) and living object (LO) detection. It is possible to detect an MO and an LO without being affected by the 85-kHz power transmission, without the need for a detection coil specifically designed to decouple from the power transmission coil and a high-pass filter. Each self-resonant detection coil consists of a unipolar coil and a comb-shaped capacitor plate. This letter describes a method that can identify an MO and an LO by scanning frequencies within a small range and detecting the slope of the output voltage as it changes with frequency. When there are no foreign objects, the absolute value of the output voltage slope is less than 0.15. The voltage slope less than −0.15 indicates the presence of MOs, while a slope greater than 0.15 indicates the presence of an LO. To verify the feasibility of the proposed method, an experimental prototype has been constructed.
6 January 2022 in IEEE Transactions on Power Electronics
Buck converters are widely used in consumer electronics, electric vehicles, and dc microgrids. Small-signal models are necessary tools to design high-quality controllers. However, most of them neglect modulation waveform ripples, which introduces significant errors under high-bandwidth controls. Recently, two models explain the influences of nondifferentiable modulation waveform ripples by their left-side derivatives at crossing points. However, this conclusion is built on the premise that infinite sideband components caused by switching have been considered, which largely complicates these models. The accurate small-signal model with finite sideband components is proposed for nondifferentiable modulation waveform ripples in this article. Based on it, the stable working region and control design of wide-input high-bandwidth Buck converters are talked about. Simulations and experiments validate the accuracy and effectiveness of the proposed model.
26 February 2025 in IEEE Transactions on Power Electronics
For automated guided vehicles (AGVs), the charging current is generally high to shorten the charging time. To achieve a high-current output, parallel connections are often chosen to distribute the current evenly across multiple coils or systems. This letter proposes a high-current output method based on intertwined receiving coils and split compensation capacitors. The receiving coil is split into four intertwined coils. They are arranged in such a way that the four coils are symmetrical to each other even with offset. Meanwhile, part or all of the compensating capacitors on the receiving side can also be split into four branches, connecting to the corresponding four receiving coils. It is proved that for the coil structure proposed when the whole compensating capacitors are split into four branches, the current difference of the four coils is the smallest. An experimental prototype is implemented. The experimental results show that the proposed method can achieve good current balancing performance of the four receiving coils even under the conditions of load change and coil position offset.