15 February 2022 in IEEE Transactions on Nuclear Science
This work analyzes the performance of the reduced precision redundancy (RPR) error mitigation technique using the fast Fourier transform (FFT) as a case study. To this purpose, several configurations of an FFT IP design were implemented in field-programmable gate array (FPGA) using reduced precision triple modular redundancy (RP-TMR) and tested under proton irradiation and fault injection. The cross section, the sensitivity to common-mode failures (CMFs), and the signal-to-noise ratio of these configurations were evaluated. The results of the radiation experiments and fault injection campaigns are in agreement and show that the RP-TMR technique may be used as an alternative to triple modular redundancy (TMR) if small errors can be tolerated, as it has a good performance in terms of error correction capabilities, area usage, and sensitivity to critical errors.
20 April 2023 in IEEE Transactions on Nuclear Science
Radiation Hardening By Design is traditionally performed using Triple Modular Redundancy, a very effective technique that introduces high overheads in terms of resources and power. The Reduced Resolution Redundancy technique presented in this work is a new approximate error mitigation technique that uses redundant circuits with lower resolution to perform computations. In this work we evaluate this technique under radiation using two different benchmarks implemented in FPGA, namely a Fast Fourier Transform and an image processing algorithm for a near infrared detector. Experimental results from proton and neutron irradiation, and fault injection campaigns, show that the Reduced Resolution Redundancy hardening technique can effectively mitigate errors with reduced overheads.
16 February 2022 in IEEE Access
Error mitigation techniques, such as Triple Modular Redundancy, introduce very large overheads. To alleviate this overhead, approximate techniques can be used. In this work we propose a novel approximate error mitigation technique based on using redundant circuits with lower resolution. As a representative case study, the approach is demonstrated for a Fast Fourier Transform, for which an optimized architecture is proposed. The approach is validated through fault injection. Experimental results show that Reduced Resolution Redundancy can significantly reduce the overhead and achieve an excellent error mitigation performance and a low sensitivity to uncorrectable errors.
22 February 2024 in IEEE Transactions on Nuclear Science
New Space missions require a short design cycle with reduced design costs and high computational capabilities. Current terrestrial COTS complex systems are the perfect candidate; however, the reliability of the devices is not granted. This work explores the reliability of complex digital systems, considering their different components. We present two different hardening architectural approaches for Multiprocessor Systems-on-Chip that combine a multicore processor and programmable logic: Duplex and D-TMR. In the proposed hardened architectures, mitigation is accomplished for both software and hardware with system recovery capabilities that rely on the rollback process available in the dual-core processors that are running in macrosynchronized lockstep mode. The coprocessors implemented in the programmable logic are hardened using Modular Redundancy techniques, and the interfaces are replicated to allow error detection and correction. Both architectures are evaluated with proton irradiation, showing a high error coverage of up to 99.3% and cross-section reduction of up to two orders of magnitude.
18 October 2023 in IEEE Access
Digital circuits for space applications can suffer from operation failures due to radiation effects. Error detection and mitigation techniques are widely accepted solutions to improve dependability of digital circuits under Single Event Upsets (SEUs) and Single Event Transients (SETs). These solutions imply design modifications that must be validated. This paper presents a formal verification method to prove that the applied fault tolerance techniques do actually prevent fault propagation as well as that the fault-tolerant circuit is functionally equivalent to the original version. The method has been implemented in an in-house software tool, VeriHard. It has been successfully applied to verify a wide variety of fault tolerance techniques, such as Triple Modular Redundancy (TMR), Duplication with Comparison (DwC), Safe Finite State Machines and Hamming encoding. Experimental results with benchmarks and industrial cases illustrates the capabilities of the method and its high performance.
4 January 2024 in IEEE Transactions on Aerospace and Electronic Systems
Error mitigation techniques have become mandatory in aerospace applications to cope with soft errors. Approximate error mitigation techniques are an attractive solution to reduce the overheads caused by conventional approaches, such as Triple Modular Redundancy. These techniques use approximate redundant copies of the target design which can be implemented with less resources, at the expense of slightly reducing the precision of the result in case of error. In this work, we propose Optimized Redundancy for Composite Algorithms (ORCA), a novel hardening technique for algorithms that may be decomposed into more simple parts. Instead of adding identical redundant modules, we use complementary modules that can be composed to implement the target design. These complementary modules can also be compared to detect errors. However, when they are correct, they produce an exact result instead of an approximate result. The experimental results show that this technique can reduce the overhead and provide a better trade-off between overhead and precision than existing approximate techniques.