Maxime Schramme

Maxime Schramme

Auto-generated profile, based on publicly available information

Maxime Schramme

ICTEAM Institute, Universit Catholique de Louvain, Ottignies-Louvain-la-Neuve, Belgium

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
24 February 2021 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
David BolDavid Bol
David Bol
MSMaxime Schramme
Maxime Schramme
LMLudovic Moreau
Ludovic Moreau
PXPengcheng Xu
Pengcheng Xu
RDRémi Dekimpe
Rémi Dekimpe
Denis FlandreDenis Flandre
Denis Flandre
Preventing device obsolescence in Internet-of-things (IoT) is mandatory for its massive deployment to be ecologically sustainable. This calls for ultralow-power (ULP) reprogrammable microcontroller units (MCUs) for long lifetime, yet with sufficient computing performance to extract the meaningful information from the sensed data before transmitting it to the cloud. In this article, we present the SleepRunner MCU with logic/memory/power management co-optimization for best exploitation of the forward back biasing (FBB) capability in fully-depleted silicon-on-insulator (FDSOI) technologies. For low active power, we use ultralow-voltage (ULV) low- V t logic with upsized gate length and asymmetric FBB, a ULP SRAM macro with low read-access energy and switched-capacitor voltage regulators (SCVRs) for ULV supply generation from a single I/O voltage. The custom ULP SRAM macro is based on an ultralow-leakage (ULL) FBB-compatible bitcell for low SRAM retention power. In addition, a dual-loop digital unified frequency/back-bias regulation (UFBR) system efficiently compensates process and temperature variations with short wakeup from the zero-back-bias deep-sleep mode. Performance is measured for a synthetic benchmark and biomedical inference applications. The measured 40-MHz 2.6- μW/DMIPS (3.3 μW/MHz) active and 131-nW/kB deep-sleep power consumptions with CPU state retention are respectively 3 × and 2.5 × lower than for a conventional MCU design in this technology. This demonstrates the interest of 28-nm FDSOI with the proposed FBB-driven system optimization for ULP MCUs.

3 April 2023 in IEEE Internet of Things Journal
Verified
Journal Article
Closed access
MGMarco Gonzalez
Marco Gonzalez
PXPengcheng Xu
Pengcheng Xu
RDRémi Dekimpe
Rémi Dekimpe
MSMaxime Schramme
Maxime Schramme
ISIvan Stupia
Ivan Stupia
David BolDavid Bol
David Bol
Wireless power transfer (WPT) is a possible alternative to batteries for supplying smart sensors. It is often described as “greener" because it avoids the use of batteries. However, this claim usually lacks the proper assessment of the environmental impacts of WPT and is particularly questionable given the poor efficiency of wirelessly transmitting power over a few meters of distance. In this paper, we design and thoroughly optimize a complete state-of-the-art WPT system and compare it to an equivalent battery-powered solution to assess whether it effectively represents an eco-friendly alternative. The proposed WPT system is a 2.45-GHz simultaneous wireless information and power transfer (SWIPT) system with beamforming and a high peak-to-average power ratio waveform for supplying a battery-less passive infrared sensor for room occupancy tracking. The final prototype of the smart sensor consumes 4and can operate in steady state at 5from the remote power head with an overall power transfer efficiency of 17/and can cold-start at 3.5. We carry out a life-cycle assessment (LCA) of the environmental impacts through four indicators, i.e., primary energy demand, global warming potential, terrestrial ecotoxicity, and freshwater consumption. Results show that for a 10-year lifetime, the WPT alternative has at least 5.5 to 10.3× higher environmental impacts than its battery-powered equivalent. This demonstrates the importance of LCA during the design of IoT smart sensors and shows that the use of meter-range 2.45¯/GHz SWIPT should be limited to applications where conventional battery-powered systems cannot be used.

1 July 2018
Verified
Conference Paper
Closed access
RDRémi Dekimpe
Rémi Dekimpe
PXPengcheng Xu
Pengcheng Xu
MSMaxime Schramme
Maxime Schramme
Denis FlandreDenis Flandre
Denis Flandre
David BolDavid Bol
David Bol
Wireless power transfer (WPT) is a possible way to achieve cheap, rapid and large-scale deployment of battery-less IoT smart sensors. However, the key challenge in designing WPT-supplied smart sensors is to ensure that the harvested power is higher than the consumed power in presence of strong WPT path loss. This paper presents the design and optimization of a smart sensor supplied by 2.45-GHz RF power and performing infrared-based motion detection and Bluetooth Low Energy (BLE) communication. The full system (RF energy harvester, power management, sensor transducer and interface, control, data processing and wireless transmission) is implemented using low-power off-the-shelf components. In the sensing sub-system, low average power is achieved using efficient duty-cycling of the analog front-end. In the harvesting sub-system, architecture choice and design of the matching network and rectifier circuit allow to optimize the total power harvesting efficiency (PHE). The implemented smart sensor can operate reliably with an incident RF power as low as -10.9 dBm. The sensing sub-system exhibits an average power of 4.3 μW and a maximum number of transmitted event packets of 60 packets per hour.

1 February 2022 in IEEE Transactions on Circuits and Systems I: Regular Papers
Verified
Journal Article
Closed access
MSMaxime Schramme
Maxime Schramme
LBLeopold Van Brandt
Leopold Van Brandt
Denis FlandreDenis Flandre
Denis Flandre
David BolDavid Bol
David Bol
Back-bias control is a new degree of freedom brought by fully-depleted silicon-on-insulator (FDSOI) CMOS technologies, which can be used to control the oscillation frequency of voltage-controlled ring oscillators (VCROs). The resulting VCRO architecture is called a back-bias-controlled oscillator (BBCO). This paper compares it with the conventional current-starved ring oscillator (CSRO) topology in terms of power consumption and phase noise figure-of-merit (FoM), while taking practical design constraints of process-voltage-temperature (PVT) robustness and frequency tuning range into account. The proposed comprehensive analysis takes advantage of relevant and compact analytical models, as well as extensive pre-layout simulation results. The comparison is made at four different target oscillation frequencies, which are representative of frequency synthesis for WiFi/Bluetooth/LPWAN wireless communications and of clock generation for smartphone/Internet-of-Things processors: 300 MHz, 868 MHz, 2.45 GHz, and 5.18 GHz. In 28-nm FDSOI technology, the results demonstrate that BBCOs can intrinsically reach 1.69 to $4.63\times $ lower minimum power consumption and slightly better FoM values than CSROs.

7 November 2022
Verified
Conference Paper
Open access
PMPol Maistriaux
Pol Maistriaux
TPThibault Pirson
Thibault Pirson
MSMaxime Schramme
Maxime Schramme
JLJérôme Louveaux
Jérôme Louveaux
David BolDavid Bol
David Bol
The Internet-of-Things (IoT) is frequently presented as an effective tool to monitor our environment and subsequently reduce the environmental footprint of human activities. However, the environmental footprint of IoT nodes themselves is often overlooked. The standardized life-cycle assessment (LCA) methodology can help in this respect. While production impacts can be estimated using LCA databases, use phase impacts are complex to model for battery-powered IoT nodes, commonly used in environmental monitoring. Indeed, battery maintenance operations involve component replacement, transportation and depend on the service lifetime which is strongly influenced by the use phase scenario. We therefore propose a comprehensive open-source parametric model of battery-powered IoT nodes use phase in environmental monitoring applications. The model assesses the overall environmental footprint, including deployment and maintenance, with an enhanced service lifetime evaluation. Using a custom node prototype, additionally validating the underlying power consumption modeling, we then analyze a case study. The use phase model fosters eco-design by allowing the optimal battery capacity identification and highlighting the impact of various parameters on the carbon footprint, e.g., use phase scenario, operating conditions, node positioning, transport scheme, and replacement strategy. Finally, the model can easily be transposed to evaluate economic aspects, motivating the environmental and economic co-optimization.

21 March 2023 in IEEE Transactions on Circuits and Systems I: Regular Papers
Verified
Journal Article
Closed access
MSMaxime Schramme
Maxime Schramme
David BolDavid Bol
David Bol
Sensitivity to process, voltage, and temperature (PVT) variations constitutes a serious obstacle in ultralow- voltage/ultralow-power (ULV/ULP) circuits and systems. To address this challenge, we propose a unified frequency/back-bias regulation (UFBBR) macro embedded in a custom ULP ARM Cortex-M4 microcontroller unit (MCU) manufactured in 28-nm FDSOI technology. The UFBBR technique combines the generation of a 32-to-80 MHz system clock and asymmetric adaptive back biasing for PVT compensation. Relying on a novel dual-output frequency-locked loop, it senses both the logic speed and the N/PMOS process imbalance using back-bias-controlled oscillators, and generates adequate forward back-bias voltages with digitally-controlled oscillators followed by switched-capacitor charge-pumps for fast current actuation. Compared to a situation with zero back biasing and appropriate frequency/voltage margins, the UFBBR provides $15\times $ of frequency boosting at 0.4 V or 180 mV of voltage reduction at 64 MHz. It leverages software-programmable configuration knobs to achieve a fast wake-up of $8 ~\mu \text{s}$ and an in-lock power of $22 ~\mu \text{W}$ , with an area overhead below 0.032 mm2. In sleep, it drives the back-bias voltages towards 0 V and disables the clock for minimum power consumption. These features help the MCU system achieve a minimum energy point of $5.5 ~\mu \text{W}$ /MHz and a sleep power of $7.7 ~\mu \text{W}$ .