Pengcheng Xu

Pengcheng Xu

Auto-generated profile, based on publicly available information

Pengcheng Xu

ICTEAM Institute, Universit Catholique de Louvain, Ottignies-Louvain-la-Neuve, Belgium

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
4 June 2019 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
PXPengcheng Xu
Pengcheng Xu
Denis FlandreDenis Flandre
Denis Flandre
David BolDavid Bol
David Bol
Simultaneous wireless information and power transfer (SWIPT) is a flexible and cheap way to supply Internet-of-Things (IoT) smart sensors avoiding battery replacement. In this paper, we analyze, model, and design a 2.45-GHz RF energy harvesting (RFEH) system based on a discrete-component matching network (MN), a custom 65-nm CMOS cross-coupled rectifier, and an off-the-shelf storage-charging power management unit (PMU), which regulates the rectifier output voltage with maximum power point tracking (MPPT). We propose a reverse global analysis to model the RFEH. It allows an accurate prediction of the power harvesting efficiency (PHE) to directly size the MN and select the RFEH MPPT regulation ratio, at different incident RF power levels. We perform parasitic-aware RFEH design to take advantage of printed circuit board (PCB)/package capacitive parasitics at the rectifier input for optimizing the π-MN with the help of the proposed RFEH modeling results. We show that this parasitic capacitance introduces a maximum bound on the real impedance at the rectifier input to ensure good impedance matching in practice. MPPT is used to help reach this target real impedance at given incident RF power, as the rectifier equivalent input impedance is a function of both its input and output voltages. Measurement results show a sensitivity as low as -17.1 dBm with a peak PHE of 48.3% at -3-dBm incident RF power. Global modeling, simulation, and measurement results demonstrate that the PHE is limited by PCB/package parasitic capacitance and that PCB/packaging technology improvement to reduce parasitic capacitance by 150 fF could boost the PHE up to 45% for a low incident RF power level of -10 dBm.

8 March 2021 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
PXPengcheng Xu
Pengcheng Xu
Denis FlandreDenis Flandre
Denis Flandre
David BolDavid Bol
David Bol
In this article, we propose a self-gating radio frequency (RF) energy harvester (RFEH) for reaching a high-power harvesting efficiency (PHE) at a low incident RF power level with a high peak-to-average power ratio (high-PAPR) waveform. It includes a power switch between a cross-coupled rectifier and its supplied load to cut off the reverse leakage current in between the short power bursts. The power switch is dynamically controlled based on an indication of the ability of the RFEH to effectively charge the load at the instantaneous incident power level. This is achieved by comparing the load voltage with the open-circuit voltage of a replica rectifier. A comparator with optional proteresis (reversed hysteresis) is proposed for compensating its logic delay at the start and at the end of the short RF power bursts. As a result, the power switch is accurately turned on only during the power bursts. The self-gating RFEH was prototyped for 2.45-GHz wireless power transfer (WPT). It includes a cross-coupled rectifier with the proposed self-gating circuit fabricated in a 65-nm process, a discrete balun, a parasitic-aware-sized π matching network, and an off-the-shelf power management unit (PMU) with maximum power point tracking (MPPT). Measurement results show sensitivity as low as -26.7 dBm with a peak PHE of 32.3% at -14.1-dBm incident power. Compared with the state-of-the-art works, the proposed design significantly improves the RFEH performance at the target low average incident power.

24 February 2021 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
David BolDavid Bol
David Bol
MSMaxime Schramme
Maxime Schramme
LMLudovic Moreau
Ludovic Moreau
PXPengcheng Xu
Pengcheng Xu
RDRémi Dekimpe
Rémi Dekimpe
Denis FlandreDenis Flandre
Denis Flandre
Preventing device obsolescence in Internet-of-things (IoT) is mandatory for its massive deployment to be ecologically sustainable. This calls for ultralow-power (ULP) reprogrammable microcontroller units (MCUs) for long lifetime, yet with sufficient computing performance to extract the meaningful information from the sensed data before transmitting it to the cloud. In this article, we present the SleepRunner MCU with logic/memory/power management co-optimization for best exploitation of the forward back biasing (FBB) capability in fully-depleted silicon-on-insulator (FDSOI) technologies. For low active power, we use ultralow-voltage (ULV) low- V t logic with upsized gate length and asymmetric FBB, a ULP SRAM macro with low read-access energy and switched-capacitor voltage regulators (SCVRs) for ULV supply generation from a single I/O voltage. The custom ULP SRAM macro is based on an ultralow-leakage (ULL) FBB-compatible bitcell for low SRAM retention power. In addition, a dual-loop digital unified frequency/back-bias regulation (UFBR) system efficiently compensates process and temperature variations with short wakeup from the zero-back-bias deep-sleep mode. Performance is measured for a synthetic benchmark and biomedical inference applications. The measured 40-MHz 2.6- μW/DMIPS (3.3 μW/MHz) active and 131-nW/kB deep-sleep power consumptions with CPU state retention are respectively 3 × and 2.5 × lower than for a conventional MCU design in this technology. This demonstrates the interest of 28-nm FDSOI with the proposed FBB-driven system optimization for ULP MCUs.

3 April 2023 in IEEE Internet of Things Journal
Verified
Journal Article
Closed access
MGMarco Gonzalez
Marco Gonzalez
PXPengcheng Xu
Pengcheng Xu
RDRémi Dekimpe
Rémi Dekimpe
MSMaxime Schramme
Maxime Schramme
ISIvan Stupia
Ivan Stupia
David BolDavid Bol
David Bol
Wireless power transfer (WPT) is a possible alternative to batteries for supplying smart sensors. It is often described as “greener" because it avoids the use of batteries. However, this claim usually lacks the proper assessment of the environmental impacts of WPT and is particularly questionable given the poor efficiency of wirelessly transmitting power over a few meters of distance. In this paper, we design and thoroughly optimize a complete state-of-the-art WPT system and compare it to an equivalent battery-powered solution to assess whether it effectively represents an eco-friendly alternative. The proposed WPT system is a 2.45-GHz simultaneous wireless information and power transfer (SWIPT) system with beamforming and a high peak-to-average power ratio waveform for supplying a battery-less passive infrared sensor for room occupancy tracking. The final prototype of the smart sensor consumes 4and can operate in steady state at 5from the remote power head with an overall power transfer efficiency of 17/and can cold-start at 3.5. We carry out a life-cycle assessment (LCA) of the environmental impacts through four indicators, i.e., primary energy demand, global warming potential, terrestrial ecotoxicity, and freshwater consumption. Results show that for a 10-year lifetime, the WPT alternative has at least 5.5 to 10.3× higher environmental impacts than its battery-powered equivalent. This demonstrates the importance of LCA during the design of IoT smart sensors and shows that the use of meter-range 2.45¯/GHz SWIPT should be limited to applications where conventional battery-powered systems cannot be used.

1 July 2019 in Integration
Verified
Journal Article
Closed access
RDRémi Dekimpe
Rémi Dekimpe
PXPengcheng Xu
Pengcheng Xu
MSMaxime Schramme
Maxime Schramme
PGPierre Gérard
Pierre Gérard
DFDenis Flandre
Denis Flandre
DBDavid Bol
David Bol

29 April 2022 in IEEE Transactions on Circuits and Systems II: Express Briefs
Verified
Journal Article
Closed access
PXPengcheng Xu
Pengcheng Xu
Denis FlandreDenis Flandre
Denis Flandre
David BolDavid Bol
David Bol
Because of the interaction between the internal blocks of an RF energy harvesting (RFEH) system, sizing a rectifier only for high power conversion efficiency (PCE) is insufficient for improving global power harvesting efficiency (PHE). This paper analyzes and sizes the rectifier by taking its input and output impedances into account with a two-port model that combines the rectifier AC and DC characteristics. The AC characteristic in this model is used for impedance-aware rectifier sizing. We target a low input-impedance rectifier for better impedance matching between the receiver antenna and the rectifier. The DC characteristic describes the rectifier power loss allocation and estimates its maximum power point. A proposed parasitic-aware matching network sizing methodology predicts the PHE is finally limited by Ohmic loss in the matching network at a low incident power level. For overcoming this limitation, this paper also analyzes the impact of multiple rectifier stages on RFEH with a high peak-to-average power ratio (high-PAPR) incident waveform for improving the PHE. We design an RFEH prototype with a sized 28nm CMOS two-stage cross-coupled rectifier. Measurement results show sensitivity as low as -28.3 dBm with a peak PHE of 31.1% at -16.5 dBm 2.45-GHz high-PAPR incident power. It has sufficient high output impedance to prevent reverse leakage without the need for an additional self-gating circuit.