1 March 2019 in Microelectronic Engineering
MEMohammadreza Nekouie Esfahani
Mohammadreza Nekouie Esfahani
+2
15 December 2017 in Advanced Functional Materials
MEMohammadreza Nekouie Esfahani
Mohammadreza Nekouie Esfahani
+3
In this work, a method for the rapid synthesis of metallic microtracks on polyetherimide is presented. The method relies on the photosynthesis of silver nanoparticles on the surface of the polymer substrates from photosensitive silver chloride (AgCl), which is synthesized directly on the polyetherimide surface. The study reveals that the use of AgCl as a photosensitive intermediate accelerates the reactions leading to the formation of silver nanoparticles by up to two orders of magnitude faster than other photodecomposition schemes. The patterning can be conducted under blue light, with notable advantages over UV exposure. Polymers of significant interest to the microelectronics and 3D printing industries can be directly patterned by light using this photography‐inspired technique at throughputs high enough to be commercially advantageous. Light exposures as short as a few seconds are sufficient to allow the direct metallization of the illuminated polyetherimide surface. The results show that the silver required for the seed layer is minimal, and the later copper electroless plating results in the selective growth of conductive tracks for circuitry on the light‐patterned areas, both on flexible films and 3D printed surfaces.
1 April 2018 in Ultrasonics Sonochemistry
In this research experimental and simulated analysis investigates the influence of megasonic (MS; 1 ± 0.05 MHz) acoustic-assisted electroplating techniques, with respect to the fabrication of through-hole via (THV) and blind-via (BV) interconnects for the Printed Circuit Board (PCB) industry. MS plating of copper down THV and BV interconnects was shown to produce measurable benefits such as increased connectivity throughout a PCB and cost savings. More specifically, a 700% increase of copper plating rate was demonstrated for THVs of 175 µm diameter and depth-to-width aspect ratio (ar) of 5.7:1, compared with electrodeposition under no-agitation conditions. For BVs, a 60% average increase in copper thickness deposition in 150 µm and 200 µm, ar 1:1, was demonstrated against plating under standard manufacturing conditions including bubble agitation and panel movement. Finite element modelling simulations of acoustic scattering revealed 1st harmonic influence for plating rate enhancement.
29 July 2019 in IEEE Access
MEMohammadreza Nekouie Esfahani
Mohammadreza Nekouie Esfahani
MSMatthew P. Shuttleworth
+3
This paper presents a selective metallization method for the newly developed 3D printable thermoplastic polyurethane elastomers (TPU): FilaFlex ® , SemiFlex TM , PolyFlex TM , and NinjaFlex ® . Silver nanoparticles were fabricated in-situ by photo-reduction on the surface of TPUs and acted as catalysts for copper ion adsorption. This method demonstrates the successful fabrication of copper patterns on flexible TPU filaments. Furthermore, Polyflex TM and acrylonitrile butadiene styrene (ABS) filaments printed in the same part have been used to enable selective electroless plating directly on PolyflexTMmaterial. Electroless copper deposited onto PolyflexTMhas a sheet resistance of (139.4 ± 7.2) m Ω /□ and a copper conductivity of (1.1 ± 0.1) × 10 7 S/m that is comparable with bulk copper. Copper-plated PolyflexTMinterconnects were fabricated as a proof of concept demonstrators.
15 February 2019 in IEEE Transactions on Electron Devices
MEMohammadreza Nekouie Esfahani
Mohammadreza Nekouie Esfahani
+2
1 February 2019 in Surface and Coatings Technology
MEMohammadreza N. Esfahani
+2