1 December 2021 in Mining of Mineral Deposits
Purpose. Assessing the process of damaging factors formation during the coal aerosol explosion in mine workings on the basis of theoretical research of the explosion of coal dust deposits in order to substantiate promising methods of protecting miners from their impact. Methods. An integrated approach is used, which includes a critical analysis of literature data on the occurrence and development of coal aerosol explosions in mine workings; theoretical research into the state of the gaseous medium at the characteristic points of the development diagram of the coal dust deposits explosion as a result of mining operations based on the laws of classical physics and chemistry. Findings. The main aspects of the explosion mechanism of dust in a powdery state, accumulated on the surfaces along the mine working perimeter, and the formation of such negative factors as the effect of gaseous medium accelerated movement, have been revealed; high temperature formed during coal and methane detonative combustion; increased gas pressure. The revealed aspects of the dust explosion mechanism make it possible to determine the main directions for protection of miners caught in the explosion. The diagram of the development of settled coal dust explosion along the mine working with normal ventilation conditions, taking into account the influence of seismic waves, has been improved. Originality. Analytical dependences, reflecting the value of gas energy at characteristic points of the diagram, have been determined, and the dynamics of the formation of negative factors caused by the explosion have been revealed. Practical implications. Possible ways of protecting miners from the impact of negative factors caused by the coal aerosol explosion and reducing the severe consequences of such accidents are proposed.
30 March 2020 in Mining of Mineral Deposits
30 December 2023 in Mining of Mineral Deposits
Purpose. The research explores the possibility of increasing the fertile properties of agricultural soils of loamy type by adding burnt-out dump mass from coal enterprises. Methods. Laboratory research on parameters of penetration and retention capacity of sorbed and meniscal water for diffe-rent burnt-out rock fractions. The burnt-out rock was sampled from the mine No. 5/6 waste rock dump in the city of Myrnohrad, Donetsk Oblast, and divided into four fractions from 0.63 to 10 mm. The water penetration coefficient of the soil with the added dump mass is measured by the velocity of water seepage into the test samples. The ability of rock additives to retain film-sorbed and capillary water is assessed by comparing the weight of dry and moistened samples of crushed dump mass. Findings. The velocity parameters of water penetration into samples of loamy mixtures with burnt-out dump mass with fractions ranging from 10 to 0.63 mm in size have been determined. It has been found that an increase in the percentage of burnt-out rock in the mixture leads to an increase in the water penetration velocity from 1.2 ml/cm2·min with a rock content of 30% to 30.66 ml/cm2·min with a rock content of 70%. The highest penetration coefficients are achieved when adding rock with a small fractional composition of 0.63-3 mm, since an increase in grain size leads to a reduction in the coefficient by se-veral times. It has been determined that with an increase in the size of the rock fractions in a loamy mixture, the retention capacity of sorbed and pore water suitable for plant nutrition decreases by approximately 40%. Originality. For the first time, the parameters of penetration coefficients, as well as the accumulation of sorbed and meniscal water for mine waste in the Selidovo-Pokrovskyi district of Donbas, have been determined. Practical implications. The results obtained can be used to improve the physical properties of agricultural soils of loamy type by increasing their water retention capacity.
1 June 2023 in Ecological Engineering & Environmental Technology
In this work, it is substantiated that it is possible to create a fire installation with parameters that will ensure higher environmental friendliness of the tests compared to large-sized furnaces. At the same time, its configuration will be universal, compact and capable of high reproducibility...
1 January 2023 in Journal of Engineering Sciences
Fire tests of reinforced concrete floor slabs do not allow the detection of the onset of the boundary state due to loss of entirety because blocks are installed on the unheated surface to reproduce the design load. This prevents the formation of cracks through which toxic combustion products, smoke, and temperature spread can penetrate. Determining a building structure’s actual fire resistance limit was fixed at the onset of any fire resistance boundary state. It was proven that calculation methods for fire resistance assessment have significant advantages over experimental methods. To reduce the number of finite elements for a rational calculation of the fire resistance assessment of a reinforced concrete hollow core slab, a geometric model of 1/4 of this structure was built. The possibility of visualizing the studied structure at full scale was realized when obtaining the calculation results. The stress-strain state of the studied structure was evaluated based on the thermal and mechanical loading results applied to the reinforced concrete hollow core slab. Thus, the work’s objective was achieved based on the calculation experiments’ results. A methodology was developed for calculating the destruction of a reinforced concrete hollow core slab while assessing its fire resistance. Scientific fundamentals for determining the onset of the boundary state of loss of entirety were developed. The proposed methodology allowed for a reliable assessment of the fire resistance of such structures.
1 January 2022 in Rudarsko-geološko-naftni zbornik
The objective of this paper is to reveal the mechanism of creating conditions for the continuous explosion of coal dust by transferring seismic energy to coal dust located along the perimeter of a working. The ANSYS software package was used to model...