Clifford Dy Cheon

Clifford Dy Cheon

Auto-generated profile, based on publicly available information

Clifford Dy Cheon

School of Electrical and Computer Engineering, Georgia Institute of Technology, Atlanta, GA 30332 USA

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 September 2020 in IEEE Microwave and Wireless Components Letters
Verified
Journal Article
Closed access
CCClifford D. Cheon
Clifford D. Cheon
MCMoon-Kyu Cho
Moon-Kyu Cho
SRSunil G. Rao
Sunil G. Rao
ACAdilson S. Cardoso
Adilson S. Cardoso
JCJeffrey D. Connor
Jeffrey D. Connor
JCJohn Cressler
John Cressler
This letter presents new wideband single-pole double-throw (SPDT) RF switches utilizing SiGe heterojunction bipolar transistors (HBTs) for both series and shunt switches. SiGe HBT, when used as a series switch, exhibits small parasitic components compared to bulk CMOS, which improves insertion loss at high frequency and supports wider bandwidth. For a series switch, three configurations are proposed: using the collector as an input (CI), using the emitter as an input (EI), and using a combination of the two in an antiparallel (AP) fashion. While all three configurations exhibit similar performance, the SPDT switch with the EI SiGe HBT exhibits the best insertion loss and isolation achieving dc-to-above 110-GHz bandwidth, 2.5 dB of insertion loss, and 27.3 dB of isolation at 60 GHz. The SPDT switch with AP SiGe HBT pair exhibits the highest linearity, with 15.6 dBm of input 1-dB compression point (IP 1 dB) at 10 GHz. With 0.61 mW of power dissipation, these new SPDT switches using SiGe HBTs exhibit similar performance to silicon-on-insulator (SOI) CMOS while obtaining higher power capability among conventional series-shunt SPDT designs.

15 March 2018 in IEEE Transactions on Microwave Theory and Techniques
Verified
Journal Article
Closed access
IJInchan Ju
Inchan Ju
CCClifford Dy Cheon
Clifford Dy Cheon
JCJohn D. Cressler
John D. Cressler
A compact highly efficient high-power SiGe Ka-band balanced frequency doubler is presented. Using a compact single-footprint four-way transformer input balun, wideband matching, and high fundamental rejection were achieved simultaneously. A cascode topology with very low base impedance termination was utilized for stable operation and high-voltage swing at the output. Two cascode differential pairs form a common-centroid configuration, resulting strong enhancement in output power, power-added efficiency (PAE), fundamental rejection, and robustness to process and supply variation. The proposed Ka-band cascode balanced frequency doubler was implemented in a 0.13-μm SiGe BiCMOS technology. Measured results show 13-dBm output power with 22% peak PAE at 34 GHz for a -1-dBm input power. The 3-dB conversion gain bandwidth is from 25 to 40 GHz, fully covering Ka-band. Peak fundamental suppression is 74.5 dB at 33 GHz, and it is higher than 35 dB over Ka-band. No performance degradation is observed after 24-h RF stress test. To the author's best knowledge, this paper has the highest efficiency, the highest output power/power density, the highest conversion gain without output buffers, and the higher or comparable fundamental rejection among any Si-based frequency doublers. Therefore, this doubler will be a promising solution for efficient and high-power local oscillator generation in 5G wireless phased-array communication system.

28 February 2020 in IEEE Microwave and Wireless Components Letters
Verified
Journal Article
Closed access
CCChristopher T. Coen
Christopher T. Coen
MFMilad Frounchi
Milad Frounchi
NLNelson E. Lourenco
Nelson E. Lourenco
CCClifford D. Y. Cheon
Clifford D. Y. Cheon
WWWyman L. Williams
Wyman L. Williams
JCJohn Cressler
John Cressler
This letter presents a novel implementation of a V-band single-pole double-throw switch that facilitates the internal calibration of radiometers by integrating an ambient noise source and an avalanche noise source. The switch is implemented in a 0.13-μm SiGe bipolar-CMOS (BiCMOS) process and uses a shunt topology with λ /4 directional couplers that inject noise from the avalanche source. The avalanche source is implemented using the collector-base junction of a SiGe heterojunction bipolar transistor (HBT) and attains a measured excess noise ratio of 18.7 dB at 60 GHz. The switch achieves a midband insertion loss of 2.0 dB and an isolation of 22 dB at 60 GHz. An excess input-referred noise temperature of 620 K is added with the noise source ON. To the best of our knowledge, this is the first avalanche noise source using a diode-configured SiGe HBT and the first monolithic two-reference switch for calibrating millimeter-wave radiometers.

15 October 2021 in IEEE Microwave and Wireless Components Letters
Verified
Journal Article
Closed access
SRSunil G. Rao
Sunil G. Rao
CCClifford D. Cheon
Clifford D. Cheon
JCJohn Cressler
John Cressler
This letter presents a millimeter-wave silicon-germanium (SiGe) distributed attenuator which uses a transformer-based attenuation core. The nonlinearities of the SiGe heterojunction bipolar transistor (HBT) are managed using an RC-load, which linearizes the device impedance versus bias. In addition, a dual-resonance transformer is used to support broadband operation, while providing control over the attenuator insertion phase. Two attenuators, one using transmission line-based impedance transformers, and one using transformer-based impedance transformers, were designed and fabricated in a 180-nm SiGe bipolar and CMOS (BiCMOS) technology platform. The attenuators achieve competitive performance in terms of bandwidth and phase error, but with low insertion loss and large attenuation range.

9 September 2021 in IEEE Transactions on Circuits and Systems II: Express Briefs
Verified
Journal Article
Closed access
CCClifford D. Cheon
Clifford D. Cheon
SRSunil G. Rao
Sunil G. Rao
WLWonsub Lim
Wonsub Lim
ACAdilson S. Cardoso
Adilson S. Cardoso
MCMoon-Kyu Cho
Moon-Kyu Cho
JCJohn Cressler
John Cressler
This brief presents a wideband, low insertion loss, high attenuation range digital step attenuator (DSA) implemented using SiGe HBTs. In a switched-type topology, the off-state capacitances ( $\text{C}_{OFF}$ ) in both reference and attenuation states cause different poles and zeros, which trigger amplitude and phase errors and limit the operating bandwidth. To achieve wide bandwidth, methods to relocate poles and zeros to the highest possible frequencies in both states are investigated. In the reference state, minimizing the size of the shunt switching transistors extends the bandwidth. In the attenuation state, switching in a capacitor at the base of an anti-parallel (AP) SiGe HBT pair series switch reduces the effective $\text{C}_{OFF}$ , enhancing the bandwidth. The proposed techniques facilitate the realization of a 16-dB attenuator cell to support wide bandwidth and offer lower insertion loss than conventional cascaded 8-dB cell designs. Fabricated in 130-nm SiGe BiCMOS technology, the proposed DSA with an attenuation range of 31.5 dB in 0.5 dB steps operates from DC to 67 GHz and achieves an insertion loss lower than 7.8 dB. The RMS amplitude error is less than 0.4 dB above 1 GHz, while the RMS phase variation is less than 13.1°.

24 February 2021 in IEEE Electron Device Letters
Verified
Journal Article
Closed access
IJInchan Ju
Inchan Ju
CCClifford D. Cheon
Clifford D. Cheon
JCJohn Cressler
John Cressler
This letter proposes a new emitter-base-collector-base-emitter (EBCBE) SiGe HBT suited for high power RF switches. Two collector-base-emitter (CBE) SiGe HBTs are merged into a single EBCBE SiGe HBT, not only to double its maximum voltage swing, but also to decrease its active area and parasitics. To further boost its power handling, a capacitive voltage distribution and a collector floating are incorporated into the new EBCBE SiGe HBT. A X-band $\lambda $ /4 shunt single-pole-double-throw (SPDT) switch using the EBCBE SiGe HBT achieves measured insertion losses and isolations of 1.2/1.3 and 29.2/23.0 dB at 10 GHz in TX/RX modes, respectively. In TX mode, measured input 1-dB power compression ( $\text{P}_{\text {1dB}}$ ) is 25.4 dBm, and it can be extended to 28.5 dBm at −0.6 V base bias of the EBCBE SiGe HBT.