Diane Titz

Diane Titz

Auto-generated profile, based on publicly available information

Diane Titz

Université Nice Sophia Antipolis

Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
6 August 2015 in IEEE Antennas and Wireless Propagation Letters
Verified
Journal Article
Closed access
ZCZihao Chen
Zihao Chen
YZYue Ping Zhang
Yue Ping Zhang
ABAimeric Bisognin
Aimeric Bisognin
DTDiane Titz
Diane Titz
FFFabien Ferrero
Fabien Ferrero
CLCyril Luxey
Cyril Luxey
This letter reports a microstrip mesh array antenna in a low temperature co-fired ceramic (LTCC) technology for 94-GHz applications. The microstrip mesh array antenna enlarges the system polarization diversity with the capability of being utilized to support the simultaneous reception in two orthogonal polarizations, as well as transmission in either polarization. The proposed design is composed of two grid arrays in two orthogonal directions, where matching stubs are specially designed to compensate the alteration of input impedance due to the direct coupling of the complementary array of another polarization. The dual linearly polarized microstrip mesh array antenna achieved a measured maximum realized gain of 13.3 dBi at 93.6 GHz, a 10-dB impedance bandwidth of 6.91%, and 3-dB gain bandwidth of 1.70% at 94 GHz as a one-port antenna.

21 May 2012 in IEEE Antennas and Wireless Propagation Letters
Verified
Journal Article
Closed access
DTDiane Titz
Diane Titz
RPRomain Pilard
Romain Pilard
FGFrédéric Gianesello
Frédéric Gianesello
FFFabien Ferrero
Fabien Ferrero
CLCyril Luxey
Cyril Luxey
DGDaniel Gloria
Daniel Gloria
During recent years, various research teams have developed 60-GHz chipset solutions, using both BiCMOS and advanced CMOS technologies. However, for the 60-GHz market to flourish, not only low-cost RFICs are required, but also cheap antennas and package solutions. In order to address these two last issues, we present the design of a Tx-Rx antenna-module using industrial high-temperature co-fired ceramics (HTCC) substrate for millimeter-wave (MMW) large-volume consumer applications. The antennas are integrated within the module. Measured realized peak gain is above 6 dBi over the 57-66-GHz frequency band.

6 April 2020 in IEEE Antennas and Wireless Propagation Letters
Verified
Journal Article
Closed access
SMSérgio Matos
Sérgio Matos
JTJorge P. Teixeira
Jorge P. Teixeira
Jorge R. CostaJorge R. Costa
Jorge R. Costa
Carlos A. FernandesCarlos A. Fernandes
Carlos A. Fernandes
NNNour Nachabe
Nour Nachabe
JVJean-Francois Vizzari
Jean-Francois Vizzari
The low-cost and compactness of transmit-array antennas (TAs) make them attractive for 5G backhaul links. However, the TA advantage is less obvious when considering the broadband operation requirement. Two main factors influence the bandwidth performance: i) the bandwidth of the unit cells; ii) the number of 360° phase wrapping zones in the aperture, which are designed for a specific frequency. Herein, we overcome these limitations by using all-dielectric unit cells (inherently broadband) and by developing a general method to quantify and manage the intricate relation between antenna gain, bandwidth and antenna height. Based on this framework we optimize, as an example, a TA design (focal distance, F=63 mm and aperture diameter D=80 mm) to comply with typical gain specification for 5G backhaul links (>30 dBi) in the WiGiG band (from 57 to 66 GHz). The feed is a dedicated compact horn ( $8\times 5\times 22 mm^{3}$ ) that provides a proper illumination of the aperture. Additive manufacturing is used to simplify the manufacturing process of the antenna. A very good agreement between simulations and experimental results is obtained, achieving good aperture efficiency for this type of antenna (42%), which rivals with existing solutions based on more expensive manufacturing techniques.

18 June 2021 in IEEE Transactions on Antennas and Propagation
Verified
Journal Article
Closed access
ABAimeric Bisognin
Aimeric Bisognin
AAAna Arboleya
Ana Arboleya
DTDiane Titz
Diane Titz
RPRomain Pilard
Romain Pilard
DGDaniel Gloria
Daniel Gloria
CLCyril Luxey
Cyril Luxey
This work presents a 12 x 12 x 0.6mm3 Ball Grid Array (BGA) module made of low-cost organic substrates which integrates transmitter (Tx) and receiver (Rx) antennas for short-range 60GHz WiGig communications. The Tx antenna is a single-element linearly-polarized aperture-coupled patch (ACP) antenna achieving a worst -12 dB matching with a broadside realized gain above 5 dBi and total efficiency higher than 50% in the 57-66 GHz band. The Rx antenna is a single-element single-fed circularly polarized ACP antenna. It exhibits a worst -14 dB matching level from 57 GHz to 66 GHz and a worst -10 dB level from 47 GHz to 66 GHz (33% relative bandwidth (BW) with respect to 60 GHz). The broadside realized gain is above 5 dBi from 61 GHz to 67 GHz and the axial ratio stays below 3 dB for a 14% BW with respect to 60 GHz. Variability of the fabrication process is analyzed by means of extensive measurements of several modules. The effect of the integration of the module in the application PCB and the device casing is also studied for realistic use. The obtained results demonstrate suitability of this High-Density Interconnect BGA packaging technology for mass production of compact low-cost millimeter-wave antenna-module for WiGig communications.

1 March 2024 in IEEE Transactions on Instrumentation and Measurement
Verified
Journal Article
Open access
AAAna Arboleya
Ana Arboleya
JLJaime Laviada
Jaime Laviada
YLYuri Alvarez Lopez
Yuri Alvarez Lopez
GAGuillermo Alvarez-Narciandi
Guillermo Alvarez-Narciandi
FLFernando Las-Heras
Fernando Las-Heras
ABAimeric Bisognin
Aimeric Bisognin
This paper presents a system for easing the characterization of probe-fed antennas on available probe stations. Many of these stations were deployed for scattering parameter measurement but not for radiation pattern acquisition. Furthermore, these latter acquisitions have traditionally required the use of mechanical positioners for the automated movement of the probe antenna along different surfaces. Integration of these mechanical systems can be complex in some probe stations due to physical constraints. This work proposes an easy-to-deploy freehand system for amplitude-only field acquisitions providing great flexibility for probe-fed antenna diagnostics. In addition, the use of feeding probes, which can be bulky if compared to low-gain antennas is known to result in partial blocking avoiding the acquisition of the radiation pattern for some angles and for causing reflections yielding some ripple and distortion in the measured pattern. The system benefits from a near-field to farfield transformation based on the source reconstruction method so that unwanted reflections can be spatially identified and filtered out. Finally, broadband phaseless acquisition based on interferometry is implemented. This technique enables to alleviate the requirements of a full-vector (i.e., amplitude and phase) acquisition without losing information regarding the time-domain behavior and to retrieve all the frequencies simultaneously without losing the coherence between them so that parameters such as the delay spread can be measured. Simulated and experimental results in the V-band from 57 to 66 GHz are analyzed to validate the proposed system. Results are in fairly agreement with both simulations and a direct far-field acquisition on a conventional automated spherical system used as a reference.

3 June 2019 in IEEE Antennas and Propagation Magazine
Verified
Journal Article
Closed access
DTDiane Titz
Diane Titz
In this article, I would like to share a reflection about how I have conducted my research projects from my Ph.D. years until now, in the context of the emergence of 5G. I want to explain how I have benefitted from the excellent partnership our group has with STMicroelectronics, while teaching high school physics and chemistry.