Adrián Moisés García-Lara

Adrián Moisés García-Lara

Auto-generated profile, based on publicly available information

Adrián Moisés García-Lara

Facultad de Ingeniería Mecánica y Eléctrica U.N., Universidad Autónoma de Coahuila, Barranquilla S/N, Guadalupe., Monclova, Coahuila, 25720, Mexico

Research Focus & Metrics

Academic Career Length

18Years (2009-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 December 2009 in Journal of Hazardous Materials
Verified
Journal Article
Closed access
JMJ.F. Martínez-Villafañe
J.F. Martínez-Villafañe
CMC. Montero-Ocampo
C. Montero-Ocampo
AGA.M. García-Lara
A.M. García-Lara

9 May 2009 in Water, Air, & Soil Pollution
Verified
Journal Article
Closed access
PDF file
AGA. M. García-Lara
A. M. García-Lara
CMC. Montero-Ocampo
C. Montero-Ocampo

1 January 2014 in Journal of Iron and Steel Research International
Verified
Journal Article
Closed access
RSRumualdo Servin
Rumualdo Servin
AGA. M. Garcia-Lara
A. M. Garcia-Lara
RMR. D. Mercado-Solís
R. D. Mercado-Solís
CVC. A. Vega-Lebrun
C. A. Vega-Lebrun

1 October 2009 in Water Science & Technology
Verified
Journal Article
Closed access
PDF file
AGA. M. García-Lara
A. M. García-Lara
CMC. Montero-Ocampo
C. Montero-Ocampo
FMF. Martínez-Villafañe
F. Martínez-Villafañe
Arsenic (As) was removed electrochemically from underground water (GW) by electrocoagulation (EC) process employing a bipolar cell configuration with continuous flow using iron electrodes. A kinetic model derived from the Lagergren equation was applied to specify the kinetics of the arsenic removal reaction. Elucidation of the effect of the liquid flow rate on the treatment time and on the simulation results of the model was achieved. The results showed that treatment times decreased from 10.50 min to 0.75 min as the flow rate decreased from 3.500 to 0.875 L min−1 and the current density varied from 15 to 45 A m−2 respectively. The used sorption kinetic model successfully describes the arsenic removal by this process. The coefficients of determination were found to be very high in all cases (R2>0.99) indicating a good fit of the experimental data to Lagergren model.

1 January 2014 in Journal of Chemistry
Verified
Journal Article
Open access
PDF file
AGA. M. García-Lara
A. M. García-Lara
CMC. Montero-Ocampo
C. Montero-Ocampo
FEFabian Equihua
Fabian Equihua
JCJ. E. Camporredondo-Saucedo
J. E. Camporredondo-Saucedo
RSRumualdo Servin
Rumualdo Servin
CMC. R. Muñiz-Valdes
C. R. Muñiz-Valdes
Contamination of natural groundwater by arsenic (As) is a serious problem that appears in some areas of Northern Central Mexico (NCM). In this research, As was removed from NCM wells groundwater by the electrocoagulation (EC) technique. Laboratory-scale arsenic electroremoval experiments were carried out at continuous flow rates between 0.25 and 1.00Lmin−1 using current densities of 5, 10, and 20Am−2. Experiments were performed under galvanostatic conditions during 5min, at constant temperature and pH. The response surface methodology (RSM) was used for the optimization of the processing variables (flow rate and current density), response modeling, and predictions. The highest arsenic removal efficiency from underground water (99%) was achieved at low flow rates (0.25Lmin−1) and high current densities (20Am−2). The response models developed explained 93.7% variability for As removal efficiency.

10 July 2025 in Technology and Health Care
Verified
Journal Article
Closed access
*R*Odin Ramírez-Fernández
*Odin Ramírez-Fernández
IDIliana Duran-Gonzalez
Iliana Duran-Gonzalez
FEFabian Equihua
Fabian Equihua
LCLaura Castruita
Laura Castruita
JSJesus E. Camporredondo Saucedo
Jesus E. Camporredondo Saucedo
EZEsmeralda Zuñiga
Esmeralda Zuñiga
Background: The increasing demand for dental implants necessitates the exploration of advanced materials and manufacturing techniques. Three-dimensional (3D) printing has emerged as a viable method for producing custom dental implants, allowing for intricate designs and improved patient-specific fits. This study focuses on the design and structural deformation assessment of 3D-printed dental implants using Finite Element Analysis (FEA). By simulating the mechanical behavior of these implants under realistic loading conditions, we aim to evaluate their performance and predict potential failure points, ultimately enhancing their reliability and longevity in clinical applications. Objective: The primary objective of this study is to conduct a comprehensive design and structural deformation assessment of three-dimensional (3D) printed dental implants using Finite Element Analysis (FEA). Specifically, the study aims to: Evaluate stress distribution and deformation patterns in three 3D-printed dental implant designs under simulated physiological loading. Compare the stiffness, strength, and elastic behavior of PEEK and CFR-PEEK under occlusal forces. Identify failure points in implants and bone–implant interfaces by analyzing high stress concentrations. Predict the biomechanical behavior of a novel dental implant by determining its elastic modulus through finite element analysis (FEA). Methods: Three models 3D were designed to understand stress distribution with different structures using PEEK as biomaterial, with 4 test conditions modeled and compared. An occlusal load was applied (230 N at 90˚ and 30˚) on the implants. Isotropic, linear elastic, and homogeneous were considerate as properties of the components. Results: Under axial loads, all models stayed within physiological stress limits, while under 30° oblique loading, Model 3 showed the lowest stress, strain, and pressure. Conclusions: FEA results indicate that 3D-printed dental implants, particularly the optimized Model 3, maintain safe stress levels under axial and oblique loads, supporting their potential for immediate loading. However, due to numerical limitations, experimental validation remains necessary to advance implant designs that optimize bone regeneration and material efficiency.