Background: The increasing demand for dental implants necessitates the exploration of advanced materials and manufacturing techniques. Three-dimensional (3D) printing has emerged as a viable method for producing custom dental implants, allowing for intricate designs and improved patient-specific fits. This study focuses on the design and structural deformation assessment of 3D-printed dental implants using Finite Element Analysis (FEA). By simulating the mechanical behavior of these implants under realistic loading conditions, we aim to evaluate their performance and predict potential failure points, ultimately enhancing their reliability and longevity in clinical applications. Objective: The primary objective of this study is to conduct a comprehensive design and structural deformation assessment of three-dimensional (3D) printed dental implants using Finite Element Analysis (FEA). Specifically, the study aims to: Evaluate stress distribution and deformation patterns in three 3D-printed dental implant designs under simulated physiological loading. Compare the stiffness, strength, and elastic behavior of PEEK and CFR-PEEK under occlusal forces. Identify failure points in implants and bone–implant interfaces by analyzing high stress concentrations. Predict the biomechanical behavior of a novel dental implant by determining its elastic modulus through finite element analysis (FEA). Methods: Three models 3D were designed to understand stress distribution with different structures using PEEK as biomaterial, with 4 test conditions modeled and compared. An occlusal load was applied (230 N at 90˚ and 30˚) on the implants. Isotropic, linear elastic, and homogeneous were considerate as properties of the components. Results: Under axial loads, all models stayed within physiological stress limits, while under 30° oblique loading, Model 3 showed the lowest stress, strain, and pressure. Conclusions: FEA results indicate that 3D-printed dental implants, particularly the optimized Model 3, maintain safe stress levels under axial and oblique loads, supporting their potential for immediate loading. However, due to numerical limitations, experimental validation remains necessary to advance implant designs that optimize bone regeneration and material efficiency.

Preg-robbing is a phenomenon in which minerals retain gold, especially due to the presence of species like carbonaceous matter and silicates in the mineral. This study demonstrates the impact of quicklime, used to adjust the pH of a gold cyanidation solution, on the retention of gold contained in pregnant cyanidation solutions and sorption mechanisms. The retention capacity of four quicklime solutions was evaluated using proportions of 200 g of lime in 800 mL of solution and 10 g of lime in 500 mL of solution. The concentrations of the gold cyanide solutions were 10, 15, and 25 ppm. The insoluble lime residue in the acetic acid solution was separated and analyzed by XRD, FTIR, elemental carbon, and Raman spectroscopy techniques. SEM and TOF-SIMS were used to analyze the lime samples after exposure to the gold cyanide solution. The results show that retention was attributable to quicklime due to the effects of its carbon and silicate content, although chemisorption and physisorption mechanisms may also be responsible.

The magnetorheological fluids have the ability to modify their viscosity quickly by subjecting it to a magnetic field, a quality that classifies them in the category of intelligent materials. Such fluids include three main components; the base fluid that is generally mineral or synthetic oil, magnetizable particles which are dispersed in the base fluid and the additives or stabilizers that prevent agglomeration and sedimentation of the particles, as well as the degradation induced by the carrier medium. The main challenge of these fluids is to maintain the rheological response to the magnetic field, as well as avoid the chemical and microstructural instability of the magnetoreological fluids. In the present investigation an exhaustive bibliographic review was carried out to understand the main aspects of these types of materials, their properties as well as the main applications in the different branches of industry and medicine. The most recent contributions focused on the chemical stability of magnetic particles through the application of surface coatings are discussed.

This study aims to quantify the effect of process parameters on the anodizing of Al6061 aluminum. To achieve this, studies on layer thickness, the porosity of the anodized surface, electrochemical techniques, X-ray diffraction, grain size estimation, and statistical analysis were conducted for three different atmospheres (without air, air, and oxygen). Parameter levels were established as follows: temperature (30 °C, 45 °C, and 60 °C), time (20 min, 40 min, and 60 min), electrolyte concentration (0.5 M), voltage (9 V), and current intensity (0.600 A). A 3³ experimental design (three factors, three levels) was proposed, and mathematical models were obtained using general factorial design. The experimental design was used to determine the three most important variables in the optimal condition. A total of 27 tests were conducted using sulfuric acid electrolytic solutions, of which 12 samples were selected by the factorial design method, which simultaneously evaluates the effects of factors and their interactions in a single experiment. Measurement of porosity and oxide layer thickness was performed using scanning electron microscopy. The purity of the anodic layer formed was characterized using X-ray diffraction techniques with a vertical goniometer X-ray diffractometer. The electrochemical behavior is presented through potentiodynamic polarization curves for the anodic layer. A general factorial design and an analysis of variance (ANOVA) were conducted to establish the significant factors for layer thickness, grain size, and reaction rate. Finally, the best results and their parameters for each response are presented.

Currently, the number of organ donors is low and there are different methods to deal with this situation, including cell cultures, decellularization and bioreactors, which play an important role in helping the required processes to be carried out in a faster and more optimized way. The objective of this work is to make the cell proliferation process efficient using a bioreactor as an alternative, in which flow simulations can be made to previously analyze how it works. The radial flow hydraulic circuit was designed and simulated in SOLIDWORKS solving Navier-Stokes equations to verify that we have a non-turbulent laminar flow and simulate cell detachment without damaging the cell matrices. The design was printed with additive printing techniques, using photosensitive resin. Bioreactors also play a part in tissue engineering, as they allow for changes that can be monitored and reproduced in particular environmental factors. This article shows the successful design of a bioreactor to proliferate mesenchymal stem cells printed and subjected to simulations, whose results lead to the conclusion that there is non-turbulent laminar flow in the behavior of the system without subjecting the cells to a possible stress that causes damage.

The influence of double continuous cold rolling followed by annealing on the texture evolution and mechanical properties of a commercial low-carbon ferritic steel was investigated. Ultrathin sheets (final thickness 0.22 mm) were produced through a two-stage cold rolling process with intermediate and final annealing at 690 °C for 35 s, followed by light temper rolling at 100 °C for 20 s. Texture evolution was characterized using Electron Backscatter Diffraction (EBSD) with Orientation Imaging Microscopy (OIM), producing pole figures and orientation distribution functions (ODFs). Mechanical properties were evaluated through Vickers microhardness and ultimate tensile strength measurements obtained from three independent locations per sample. Quantitative ODF analysis (φ₂ = 45°) revealed that γ-fiber ({111}//ND) intensity increased after each cold reduction stage and decreased after annealing due to recrystallization. The α-fiber (110/RD) and cube components (001//RD) showed a slight increase after annealing. The final ultrathin sheet exhibited moderate γ-fiber intensity (≈3 M.R.D), low Vickers microhardness (100–150 HV), and tensile strength (400–450 MPa). These results demonstrate controlled evolution of texture and microstructure during double cold rolling and annealing, providing a basis for future studies on forming-related behavior without directly assessing formability.