4 August 2020 in IEEE Transactions on Power Electronics
The unprecedented high-speed switching of Wide Bandgap (WBG) power devices may change the partial discharge (PD) behaviors of power modules, busbars and loads. However, very little research has been published on PD behaviors under square-wave pulses with ultra-fast dv/dt. To address this problem, this paper studies PD behaviors of direct bonded copper (DBC) samples with different trench distances and chamfer radii under single and repetitive square pulses with ultra-fast dv/dt. The results show that for the single pulse excitation partial discharge inception voltage (PDIV) decreases with increasing rise time if the pulse width is shorter than 300 s, and PDIV decreases with increasing pulse width. For repetitive pulse excitation, PDIV increases linearly with trench distance if the chamfer radius is larger than 0.5 mm, while it follows a concave curve if the chamfer radius is less than 0.5 mm. On the other hand, for a fixed trench distance, the PDIV changes quadratically with the chamfer radius increasing from 0 mm (right angle) to 0.7 mm. Based on experimental results, a PD model with bubble expansion theory is to explain the PD mechanism under ultra-fast dv/dt excitation, and an empirical equation for PDIV prediction is also derived.
5 March 2020 in IEEE Transactions on Power Electronics
This article presents the design and development of a 7-kV dc bus, 1-MVA, 0-1000 Hz modular multilevel converter (MMC) prototype for high speed medium-voltage variable frequency drives. The system is designed based on 1.7-kV silicon carbide (SiC) MOSFETs. First, the full in-depth design of the prototype is provided, including the submodules, arm inductors, and system integration. Then, the unique control scheme and the control hardware design are presented to achieve the full-frequency range operation. The power loss based on Si and SiC devices is analyzed. Finally, experimental results are presented to demonstrate the performance of both the SiC-based submodule and the full-scale MMC system. Compared with the traditional Si-based solution, the established SiC MMC can reduce the drive system volume by 75% and achieve 325% power density, and the peak energy efficiency reaches around 99.35%.
2 November 2018 in IEEE Transactions on Industry Applications
This paper presents the short-circuit behavior and degradation of 650-V/60-A E-mode GaN HEMTs under various test conditions. First, the paper introduces the basic information of device, test method, and platform. Subsequently, single pulse, 10 $\mu$ s short-circuit tests are performed from 50 V to 400 V to extract the typical behavior of devices. Both short-circuit current self-regulation phenomenon and quick failure have been observed. Simultaneously, the device short-circuit behavior at various gate drive voltages and temperatures have been explored to identify the protection condition. Then, repetitive short-circuit tests have been performed to reveal device degradation trends. As a result, their output current reduction and gate-to-source threshold voltage shift have occurred. This work shows the critical need to improve the robustness of this type of GaN HEMT from the device and circuit perspectives.
4 June 2021 in IEEE Electrification Magazine
Transportation electrification has been gaining momentum in the past two decades. Ground vehicle electrification is the front-runner of this paradigm shift as electric vehicles slowly but steadily penetrate the consumer market. Besides higher costs, one of the main concerns related to vehicle electrification is range anxiety, which is the result of the limited accessibility of charging ports and stations as well as the relatively low energy density and cycle life of batteries. Lower cost, higher power, and more accessible battery chargers are among potential solutions to address the expense and range anxiety issues.
10 August 2021 in IEEE Transactions on Industry Applications
This paper proposes a novel DC-DC topology, enabling a plug-in electric vehicle to charge its HV battery using a wireless power transfer system. By interfacing the wireless power transfer systems receiver coil to the electric vehicles on-board bidirectional conductive charger, a common rectifier and secondary matching capacitors are shared between the two sub-systems. The bi-directional dc-dc converter within the onboard charger is optimized to operate over two frequency bands. Thus, guaranteeing compliance with the working frequency and interoperability requirements proposed by the SAE J2954 for a wireless power transfer system without degrading the power density requirement of a bidirectional on-board charger. Through component sharing between the two sub-systems, a reduction in the overall size and cost of the on-board electronics is achieved. Simulation results are provided to validate the fundamental operation of the proposed circuit. Finally, a prototype is built to validate the assumptions.
7 June 2023 in IEEE Journal of Emerging and Selected Topics in Power Electronics
The fight against global climate change demands the electrification of aircraft propulsion. One of the most significant and distinct challenges that future multi-megawatt electrified propulsion will face is high voltage at high altitudes, which could cause significant partial discharge and reduce the reliability of the propulsion system. Recognizing this challenge, a multi-disciplinary research team has proposed, designed, built, and preliminarily tested a 2-kV 1-MW 20,000 RPM integrated modular motor drive (IMMD) with an unprecedented weight power density of 9 kW/kg. This paper presents the architecture, major design approaches, test results of associated power electronics systems at the rated voltage and current, and preliminary test results of the full IMMD prototype. Full power and system-level altitude tests of the IMMD are already planned at the National Aeronautics and Space Administration (NASA’s) test facility.