He Li

He Li

Auto-generated profile, based on publicly available information

He Li

Department of Electrical and Computer Engineering, The Ohio State University, Columbus, OH, USA

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 March 2020 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
Jianyu PanJianyu Pan
Jianyu Pan
ZKZiwei Ke
Ziwei Ke
MSMuneer Al Sabbagh
Muneer Al Sabbagh
HLHe Li
He Li
KPKarun Arjun Potty
Karun Arjun Potty
LXLongya Xu
Longya Xu
This article presents the design and development of a 7-kV dc bus, 1-MVA, 0-1000 Hz modular multilevel converter (MMC) prototype for high speed medium-voltage variable frequency drives. The system is designed based on 1.7-kV silicon carbide (SiC) MOSFETs. First, the full in-depth design of the prototype is provided, including the submodules, arm inductors, and system integration. Then, the unique control scheme and the control hardware design are presented to achieve the full-frequency range operation. The power loss based on Si and SiC devices is analyzed. Finally, experimental results are presented to demonstrate the performance of both the SiC-based submodule and the full-scale MMC system. Compared with the traditional Si-based solution, the established SiC MMC can reduce the drive system volume by 75% and achieve 325% power density, and the peak energy efficiency reaches around 99.35%.

2 November 2018 in IEEE Transactions on Industry Applications
Verified
Journal Article
Closed access
HLHe Li
He Li
XLXiao Li
Xiao Li
XWXiaodan Wang
Xiaodan Wang
XLXintong Lyu
Xintong Lyu
Haiwei CaiHaiwei Cai
Haiwei Cai
JWJin Wang
Jin Wang
This paper presents the short-circuit behavior and degradation of 650-V/60-A E-mode GaN HEMTs under various test conditions. First, the paper introduces the basic information of device, test method, and platform. Subsequently, single pulse, 10 $\mu$ s short-circuit tests are performed from 50 V to 400 V to extract the typical behavior of devices. Both short-circuit current self-regulation phenomenon and quick failure have been observed. Simultaneously, the device short-circuit behavior at various gate drive voltages and temperatures have been explored to identify the protection condition. Then, repetitive short-circuit tests have been performed to reveal device degradation trends. As a result, their output current reduction and gate-to-source threshold voltage shift have occurred. This work shows the critical need to improve the robustness of this type of GaN HEMT from the device and circuit perspectives.

23 January 2020 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
XLXintong Lyu
Xintong Lyu
HLHe Li
He Li
YAYousef Abdullah
Yousef Abdullah
KWKe Wang
Ke Wang
BHBoxue Hu
Boxue Hu
SBSandeep Bala
Sandeep Bala

11 April 2019 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
KPKarun Arjun Potty
Karun Arjun Potty
EBEric Bauer
Eric Bauer
HLHe Li
He Li
JWJin Wang
Jin Wang
Power electronic converters and electric motor drives have found increased application in dc microgrids, electric automobiles, and ships. Such converters when driving loads in a regulated fashion act as constant power loads (CPLs). These CPLs can cause destabilizing effects on the grid because of their negative incremental impedance. This paper proposes a method to dynamically stabilize CPLs at the point of load by making them behave as adaptive Smart Resistors by using high-bandwidth power converters and energy storage units. These Smart Resistors can work with smart sources to realize ultimate intelligent power networks. The control strategies needed to achieve the concept, including voltage and current trajectory control principles, are analyzed and validated with a hardware test setup.

1 September 2018
Verified
Conference Paper
Closed access
YZYue Zhang
Yue Zhang
GYGe Yang
Ge Yang
XHXiaoteng He
Xiaoteng He
MEMohamed Elshaer
Mohamed Elshaer
WPWilliam Perdikakis
William Perdikakis
CCChingchi Chen
Chingchi Chen
Electric vehicle (EV) chargers are traditionally isolated from the grid. Non-isolated chargers have great potential as they enable higher power density at lower cost. Integrated chargers have the potential to utilize existing onboard, high power-rated electronic components for Level 3 charging. Four possible non-isolated integrated charger topologies based on permanent magnet synchronous machine (PMSM) are introduced at the beginning of this paper. Then, the issue of common mode (CM) leakage current through the on-board filters is identified and analyzed. It is found that the leakage current could rise to dangerous levels and cause potential electric shocks to users. The negative influence and safety risks from the leakage current for different grounding systems are also discussed. Experimental results are presented to validate the leakage current analysis. Finally, possible mitigation techniques of the leakage current are discussed.

2 February 2018 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
CYChengcheng Yao
Chengcheng Yao
ZWZhongjing Wang
Zhongjing Wang
WLWenwei Li
Wenwei Li
HLHe Li
He Li
JQJinziyang Qian
Jinziyang Qian
JWJin Wang
Jin Wang
This paper investigates the power module design for better common-mode (CM) noise and thermal performance. A high-frequency full-bridge diode rectifier is selected as a case study. The most influential factors in CM noise generation and mitigation are first identified with a simplified CM equivalent model and a comprehensive parametric study. Studies show proper parasitic value and parasitics symmetry can improve CM noise performance. The analysis of packaging structures indicates the vertical module has better CM noise and thermal performance than the traditional lateral wire-bonded module. To validate this, both modules are designed and prototyped for verification. The thermal simulation shows the vertical module exhibits a 25.5% lower thermal resistance from junction to case and a 51% increase of power density in a force-air-cooled condition. Experiments also reveal 15 dB of CM noise reduction from 150 kHz to 6 MHz and a 32 % improvement of power density in a force-air-cooling condition. Finally, a case study demonstrates the vertical power module CM noise performance in a typical unsymmetrical topology. This results in a 30 dB CM noise reduction up to 6 MHz.