Giovanna Stella

Giovanna Stella

Auto-generated profile, based on publicly available information

Giovanna Stella

Department of Electrical Electronic and Computer Science Engineering, University of Catania, Via Santa Sofia 64, 95125 Catania, Italy

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
26 February 2020 in Micromachines
Verified
Journal Article
Open access
PDF file
Salvina GaglianoSalvina Gagliano
Salvina Gagliano
GSGiovanna Stella
Giovanna Stella
Maide BucoloMaide Bucolo
Maide Bucolo
Microfluidics processes play a central role in the design of portable devices for biological and chemical samples analysis. The bottleneck in this technological evolution is the lack of low cost detection systems and control strategies easily adaptable in different operative conditions, able to guarantee the processes reproducibility and reliability, and suitable for on-chip applications. In this work, a methodology for velocity detection of two-phase flow is presented in microchannels. The approach presented is based on a low-cost optical signals monitoring setup. The slug flow generated by the interaction of two immiscible fluids {air and water} in two microchannels was investigated. To verify the reliability of the detection systems, the flow nonlinearity was enhanced by using curved geometries and microchannel diameter greater than 100 μ m. The optical signals were analyzed by using an approach in a time domain, to extract the slug velocity, and one in the frequency domain, to compute the slug frequency. It was possible to distinguish the water and air slugs velocity and frequency. A relation between these two parameters was also numerically established. The results obtained represent an important step in the design of non-invasive, low-cost portable systems for micro-flow analysis, in order to prove that the developed methodology was implemented to realize a platform, easy to be integrated in a System-on-a-Chip, for the real-time slug flow velocity detection. The platform performances were successfully validated in different operative conditions.

15 June 2023 in Polymers
Verified
Journal Article
Open access
PDF file
Lorena SaittaLorena Saitta
Lorena Saitta
ECEmanuela Cutuli
Emanuela Cutuli
GCGiovanni Celano
Giovanni Celano
Claudio TostoClaudio Tosto
Claudio Tosto
GSGiovanna Stella
Giovanna Stella
Maide BucoloMaide Bucolo
Maide Bucolo
In this work, a quadratic polynomial regression model was developed to aid practitioners in the determination of the refractive index value of transparent 3D printable photocurable resins usable for micro-optofluidic applications. The model was experimentally determined by correlating empirical optical transmission measurements (the dependent variable) to known refractive index values (the independent variable) of photocurable materials used in optics, thus obtaining a related regression equation. In detail, a novel, simple, and cost-effective experimental setup is proposed in this study for the first time for collecting the transmission measurements of smooth 3D printed samples (roughness ranging between 0.04 and 2 μm). The model was further used to determine the unknown refractive index value of novel photocurable resins applicable in vat photopolymerization (VP) 3D printing techniques for manufacturing micro-optofluidic (MoF) devices. In the end, this study proved how knowledge of this parameter allowed us to compare and interpret collected empirical optical data from microfluidic devices made of more traditional materials, i.e., Poly(dimethylsiloxane) (PDMS), up to novel 3D printable photocurable resins suitable for biological and biomedical applications. Thus, the developed model also provides a quick method to evaluate the suitability of novel 3D printable resins for MoF device fabrication within a well-defined range of refractive index values (1.56; 1.70).

16 March 2022 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Open access
PDF file
Lorena SaittaLorena Saitta
Lorena Saitta
GCGiovanni Celano
Giovanni Celano
Gianluca CicalaGianluca Cicala
Gianluca Cicala
MFM. E. Fragalà
M. E. Fragalà
GSGiovanna Stella
Giovanna Stella
Maide BucoloMaide Bucolo
Maide Bucolo
In this work, the use of projection micro-stereolithography (PμSL) to 3D print a micro-optofluidic device for slug flow detection is presented. For comparison purposes, a poly-dimethylsiloxane (PDMS)–based device was also manufactured by a novel master–slave 3D printing approach. The micro-optofluidic device has a microfluidic T-junction with a micro-optical section that consists of two optical fiber insertions used for slug flow detection. The design of the device also includes two micro-channels for the optical fiber’s insertion, needed to acquire a light signal, which give a direct information about the microfluidic channel inner flow by exploiting the absorption phenomenon. The working principle in the detection is based on a different light transmission correlated to the fluid interfering with the laser beam in a micro-channel section. The two materials used for the two manufacturing approaches were fully characterized in terms of their surface properties via both Atomic Force Microscopy (AFM) and angle of contact measure.The process within the two micro-channels was monitored optically and a signal correlated to the slug passage was analyzed for the flow tracking. A wide experimental campaign was done for the device manufactured through the PμSL technique in different operative conditions. Thus, the optimal one was identified through the Analysis of Variance (ANOVA). Then, a detailed comparison between the slug process detected inside the HTL resin device and the PDMS device was carried out to evaluate the pros and cons of using different materials and fabrication techniques. The analysis run on the two devices revealed that the HTL resin device can be used for slug flow detection, but future research is still needed to obtain a resin allowing to outperform the PDMS device.

18 November 2023 in Micromachines
Verified
Journal Article
Open access
PDF file
ECEmanuela Cutuli
Emanuela Cutuli
DSDario Sanalitro
Dario Sanalitro
GSGiovanna Stella
Giovanna Stella
Lorena SaittaLorena Saitta
Lorena Saitta
Maide BucoloMaide Bucolo
Maide Bucolo
This work proposes a multi-objective polydimethylsiloxane (PDMS) micro-optofluidic (MoF) device suitably designed and manufactured through a 3D-printed-based master–slave approach. It exploits optical detection techniques to characterize immiscible fluids or microparticles in suspension inside a compartment specifically designed at the core of the device referred to as the MoF chamber. In addition, we show our novel, fast, and cost-effective methodology, dual-slit particle signal velocimetry (DPSV), for fluids and microparticle velocity detection. Different from the standard state-of-the-art approaches, the methodology focuses on signal processing rather than image processing. This alternative has several advantages, including the ability to circumvent the requirement of complex and extensive setups and cost reduction. Additionally, its rapid processing speed allows for real-time sample manipulations in ongoing image-based analyses. For our specific design, optical signals have been detected from the micro-optics components placed in two slots designed ad hoc in the device. To show the devices’ multipurpose capabilities, the device has been tested with fluids of various colors and densities and the inclusion of synthetic microparticles. Additionally, several experiments have been conducted to prove the effectiveness of the DPSV approach in estimating microparticle velocities. A digital particle image velocimetry (DPIV)-based approach has been used as a baseline against which the outcomes of our methods have been evaluated. The combination of the suitability of the micro-optical components for integration, along with the MoF chamber device and the DPSV approach, demonstrates a proof of concept towards the challenge of real-time total-on-chip analysis.

29 April 2025 in Biomedical Signal Processing and Control
Verified
Journal Article
Open access
ECEmanuela Cutuli
Emanuela Cutuli
GSGiovanna Stella
Giovanna Stella
FGFrancesca Guarino
Francesca Guarino
Maide BucoloMaide Bucolo
Maide Bucolo

27 January 2022 in Micro
Verified
Journal Article
Open access
PDF file
FCFabiana Cairone
Fabiana Cairone
FAFrancesco Gallo Afflitto
Francesco Gallo Afflitto
GSGiovanna Stella
Giovanna Stella
Gianluca CicalaGianluca Cicala
Gianluca Cicala
MAMohamed Ashour
Mohamed Ashour
Maide BucoloMaide Bucolo
Maide Bucolo
Microscale optofluidic devices are a category of microscale devices combining fluidic and optical features. These devices typically enable in-situ fluid flow measurement for pharmaceutical, environmental or biomedical applications. In micro-optofluidic devices, in order to deliver, as close as possible, the input light to the sample or a specific chip section and, collect the output signal, it is necessary to miniaturize optical components. In this paper, two low-cost technologies, 3D Printing PDMS-based and laser cutting PMMA-based (PDMS stands for Poly-dimethyl-siloxane and PMMA for Poly-methyl-methacrylate), were investigated as novel methods to realize micro-optical waveguides (μWGs) comparing their performances. An ad-hoc master-slave protocol developed to realize PDMS components by 3D Printing has been fully optimized. The manufacturing technologies proposed require simple and low-cost equipment and no strictly controlled environment. Similar results are obtained for both the micro-optical waveguides realized. Their losses, disregarding the losses caused by the fibers’ alignment and the miss-match of the geometry with the waveguide, are of the order of 20%, almost equivalent for both approaches (PDMS-μWG and PMMA-μWG). The losses are of the order of 10% when the PDMS-μWG is shielded by a copper layer, with a significant improvement of the signal acquired. The results obtained show the possibility of using the two low-cost technologies presented for the realization of micro-optical waveguides suitable to be integrated in micro-optofluidic devices and the potential of creating micro-optical paths inside micro-embedded systems.