This paper presents a reconfigurable bidirectional wireless power and data transceiver (RB-WPDT) integrated circuit (IC) for wearable biomedical applications. The proposed transceiver can be reconfigured as a differential class-D power amplifier or a full-wave rectifier depending on the mode signal to facilitate power transfer between devices. Additionally, the RBWPDT system supports full-duplex (FD) data transmission via a single inductive link, enabling real-time control and monitoring between devices. The proposed FD method utilizes frequency shift-keying pulse-width modulation (FSK-PWM) for downlink and load shift-keying (LSK) for uplink, achieving simultaneous bidirectional data transmission by ensuring that the FSK-PWM downlink and LSK uplink data channels operate independently with minimal interference. The measured downlink and uplink data rates are 250 kb/s and 67 kb/s, respectively. The measured overall DC-to-DC efficiency is 49%, while the power delivered to the load (PDL) is 120 mW at a 5 mm distance. The proposed chip is fabricated using a 180-nm BCD CMOS process.
When it is necessary to detect various physiological signals of the human body, clothing embroidered with near-field effect patterns can be used as a long-term power supply medium to supply power to long-distance transmitters and receivers to form a wireless power supply system. The proposed system uses an optimized parallel circuit to achieve a power transfer efficiency of more than five times higher than that of the existing series circuit. The power transfer efficiency of simultaneously supplying energy to multiple sensors is increased higher than five times and even more when only one sensor is coupled. When powering eight sensors at the same time, the power transmission efficiency can reach 25.1%. Even when eight sensors powered by the coupled textile coils are reduced to one, the power transfer efficiency of the whole system can reach 13.21%. Additionally, the proposed system is also applicable when the number of sensors ranges from 2 to 12.
16 May 2024 in IEEE Transactions on Biomedical Circuits and Systems
Active implantable medical devices (AIMDs) rely on batteries for uninterrupted operation and patient safety. Therefore, it is critical to ensure battery safety and longevity. To achieve this, constant current/constant voltage (CC/CV) methods have been commonly used and research has been conducted to compensate for the effects of built-in resistance (BIR) of batteries. However, conventional CC/CV methods may pose the risk of lithium plating. Furthermore, conventional compensation methods for BIR require external components, complex algorithms, or large chip sizes, which inhibit the miniaturization and integration of AIMDs. To address this issue, we have developed a pulse charger that utilizes pulse current to ensure battery safety and facilitate easy compensation for BIR. A comparison with previous research on BIR compensation shows that our approach achieves the smallest chip size of 0.0062 mm 2 and the lowest system complexity using 1-bit ADC. In addition, we have demonstrated a reduction in charging time by at least 44.4% compared to conventional CC/CV methods, validating the effectiveness of our system’s BIR compensation. The compact size and safety features of the proposed charging system make it promising for AIMDs, which have space-constrained environments.
4 June 2026 in IEEE Transactions on Industrial Electronics
This article presents a single-stage wireless pulse charger (WPC) for biomedical and wearable devices that integrates AC–DC conversion and battery charging profile into a single power stage. The WPC utilizes a pulse current charging profile to effectively mitigate lithium plating, thereby ensuring extended battery longevity. By utilizing the zero-current intervals, the WPC eliminates voltage drops caused by the battery’s built-in resistance (BIR), enabling direct and accurate sensing of the cell voltage without complex computational circuitry. This robust BIR compensation eliminates the need for the inefficient constant-voltage (CV) mode, significantly reducing charging time while preventing overcharging through precise end-of-charging (EOC) detection. In the fully charged state, the WPC enters a freewheeling state to automatically minimize power consumption and enable the seamless management of charging and recharging modes. Fabricated in a 180-nm BCD process, the proposed WPC achieves a peak receiver efficiency of 92.6%.
1 November 2026 in IEEE Journal of Solid-State Circuits