2 November 2023 in IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control
In this study, we investigate the dispersive behavior of the electromechanical coupling coefficient ( k eff 2 ) for shear-horizontal (SH) and Rayleigh surface acoustic wave (SAW) modes in a YX-LiNbO 3 (LN)/SiO 2 /Si substrate across various wavelengths. Due to the difference in velocity dispersion between the SH and Rayleigh modes, mode coupling can be observed when these two modes operate at closely proximate frequencies, leading to a notable variation in their k eff 2 . With a careful design, SH and Rayleigh modes can be tuned to achieve a mode-decoupling state for enhancing the k eff 2 of the SH-SAW and suppressing the presence of the Rayleigh mode in YX-LN/SiO 2 /Si. Consequently, a series of proof-of-concept SH-SAW resonators with wavelengths (λ) ranging from 1.6 μm to 4.8 μm are fabricated. The optimized resonator with a λ of 2.8 μm exhibits a resonant frequency of 1.064 GHz, an effective k eff 2 of 47.7%, a maximum Bode-Q of around 900, and an 18 dB rejection of spurious modes spanning from 0.5 to 3 GHz, without the presence of Rayleigh mode.
29 April 2024 in IEEE Transactions on Electron Devices
This work demonstrates the spectrum-clean shear-horizontal surface acoustic wave (SH-SAW) resonators with large electromechanical coupling coefficient ( ${k}_{\text {eff}}^{{2}}{)}$ and substantial admittance ratio ( ${A}_{R}{)}$ in a lithium niobate on insulator (LNOI) platform in the gigahertz range. The solidly mounted LN waveguide is acoustically engineered through optimal selection of wavelength ( $\boldsymbol {\lambda }$ ) and electrode thickness for eliminating the undesired Rayleigh SAW mode while enhancing the ${k}_{\text {eff}}^{{2}}$ of the SH-SAW. Consequently, the transverse spurious modes are suppressed using repetitive cross-interdigital transducers (X-IDT), with minimal tradeoffs to other key performance parameters. As a proof-of-concept, the SH-SAW resonators are fabricated on a 1.2-/0.5-/500- $\boldsymbol {\mu }\text{m}$ YX-LN/SiO2/Si functional substrate with gold electrodes, exhibiting a resonant frequency of 1.17 GHz, a ${k}_{\text {eff}}^{{2}}$ of 43.3%, an ${A}_{R}$ of 74.3 dB, and a spectrum-clean response at $\boldsymbol {\lambda }$ of $2.6~ \boldsymbol {\mu }\text{m}$ with only a few minor spurious modes away from the main mode, offering significant potential for applications in wideband RF circuits.
21 November 2024 in IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control
This paper reports a cryogenic study on wideband shear horizontal surface acoustic wave (SH-SAW) devices based on an emerging Y-cut LiNbO 3 /SiO 2 /Sapphire (LNOS) platform. To perform a comprehensive study, low-loss acoustic delay lines (ADLs) equipped with unidirectional transducers were designed with a wavelength (λ) of 4 μm (900 MHz) and a wide fractional bandwidth (FBW) of around 7%, featuring various physical delays ranging from 5λ to 200λ as testing structures. By cooling the temperature down to 5 K, the insertion loss (IL) of the longest ADL and the extracted propagation loss (PL) were characterized as 4.1 dB and 3.5 dB/mm, respectively. Compared with an IL of 5.78 dB and a PL of 4.37 dB/mm at 275 K, the temperature-dependent acoustic losses diminish at low temperatures, with the overall PL dominated by the acoustic waveguide formed by the acoustic velocity mismatch between layers. Furthermore, a one-port resonator (λ = 2.8 μm) with a large perceived effective electromechanical coupling greater than 40% was also characterized using the same technique, showing a 2X boost in the maximum Bode-Q at cryogenic temperatures. This study not only characterized the acoustic properties of wideband LNOS SH-SAW devices but also validated their excellent performance across a wide temperature range, suggesting their potential applications in cryogenic phononic circuits.
3 September 2024 in IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control
In this work, we investigate, for the first time, a low-phase noise and wide-tuning range voltage-controlled surface acoustic wave oscillator (VCSO) based on a lithium niobate on sapphire (LNOS) low-loss acoustic delay line (ADL). The thin-film LN/SiO 2 bilayer acoustic waveguide, together with the single-phase unidirectional transducer (SPUDT) design, is key to attaining low insertion loss (IL) by enhancing the energy confinement and directionality. Based on a high performance ADL with an IL of only 5.2 dB, a fractional bandwidth (FBW) of 5.38%, and a group delay of 110 ns, the VCSO is implemented by commercially available circuit components using a series-resonant topology. The LNOS ADL oscillator operates at 888 MHz, showcasing a low phase noise of -94.1 dBc/Hz at 1-kHz offset and a root-mean-square (RMS) jitter of only 30.26 fs (integrated from 12 kHz to 20 MHz) while only consuming 16 mA of supply current. Featuring a wide frequency tuning range of 6,630 ppm, the proposed VCSO is a promising low-noise, low-power, high-frequency timing device for emerging applications.
22 August 2024 in IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control
Abstract-The need for wide-band radio frequency front ends (RFFE) with next-generation wireless protocols highlights the importance of electromechanical coupling k pff 2 . The hetero acoustic layered (HAL) surface acoustic wave (SAW) resonator with aluminum (Al) electrodes has shown superior performance compared to conventional SAW devices. Despite gold (Au) having excellent conductivity and stable properties, its high acoustic absorption and low phase velocity have made it less favorable for electrodes. This work demonstrates that high-performance shear horizontal (SH)-SAW resonators can be fabricated on the lithium niobate-on-insulator (LNOI) platform using a setup specifically designed for an Au electrodes. Experimental validation shows that the device achieves a high quality factor ( Q ) over 870, excellent k eff 2 up to 40%, and operates around 765 MHz. Unwanted transverse spurious modes are suppressed through adequate electrode design, and the temperature stability of LNOI SH-SAW with Au electrodes is discussed. This study highlights gold’s potential as an electrode material for high k eff 2 , clean spectrum, and wideband applications.
10 October 2024 in IEEE Electron Device Letters
In this study, we explore the design, simulation, and implementation of a magnetic-free radio frequency (RF) circulator using spatiotemporal modulated thin film surface acoustic wave delay lines. The four-port circulator is designed based on two tightly packed low-propagation loss acoustic delay lines (ADLs) on a single LN/SiO 2 /sapphire (LNOS) chip with sequentially-switched delay line (SSDL) topology, complemented by two external switch modules composed of commercially available RF switches. The ADLs are characterized by a low insertion loss (IL) of 5.54 dB, a wide 3-dB bandwidth of 5.45%, and a large group delay of 100 ns at 880 MHz, operating in shear horizontal (SH) mode. The implemented circulator achieves a nonreciprocal contrast of 18.2 dB and 20.8 dB between IL of 10.8 dB and isolation of 29 dB (port 3 to port 1) and 31.6 dB (port 4 to port 1) over an isolation bandwidth of 6% (53.6 MHz), with a low modulation frequency of 2.27 MHz.