20 February 2020 in IEEE Transactions on Circuits and Systems I: Regular Papers
This paper presents design considerations and methodology for D-band transformer-based Class-AB gain-boosting power amplifiers (PAs) in three advanced silicon technologies: 28 nm bulk CMOS (complementary metal oxide semiconductor), 22 nm FD-SOI (fully-depleted silicon on insulator), and 130 nm SiGe BiCMOS (Silicon-germanium bipolar-CMOS). Firstly, the choice of processes and models together with de-embedding approaches are discussed and described. Then, a general design flow for a transformer-based matching network (TMN) is introduced to accelerate the design of multistage PAs. Further, two gain-boosting topologies are analyzed. The influence of capacitive gain-boosting on PA performance (maximum available power gain Gmax, saturation power Psat, drain efficiency DE and power-added efficiency PAE) is studied for different silicon technologies after properly sizing the PA transistors to reach an optimum load resistance Ropt. The inductive gain-boosting PA is explored and compared with the capacitive gain-boosting one in SiGe BiCMOS to achieve an even higher Psat while maintaining a high Gmax. Finally, A D-band 4-stage capacitive gain-boosting PA is fabricated in a 28 nm bulk CMOS process as a reference to verify the design methodology and simulation results, and its detailed design considerations are described. This prototyped D-band PA achieved the state-of-the-art results: a 22.5 dB Gp, 6.6 % PAE, 8 dBm Psat and 81.1 FoM with only 0.0265 mm² core area.
30 April 2018 in IEEE Journal of Solid-State Circuits
An eight-way phased-array TRX front-end with RF phase shifting and on-chip transmit/receive switching is implemented in 28-nm CMOS. The TX P 1dBout and RX noise figure (NF) are 10 dBm and 6.8 dB, respectively. The active phase shifter shows less than 5° phase resolution and amplitude errors within ± 0.35 dB. The 9.6-mm 2 chip consumes 231 mW in RX and 508 mW in the TX mode from a 0.9-V supply. When combined with PCB antennas, a ±46° scan angle is obtained with <;0.4 dB peak-to-peak gain ripples without calibration. We also present an approach to express the noise performance of a phased-array receiver in terms of the effective isotropic NF, as an extension to the NF, which is only defined for a two-port system.
11 June 2015 in IEEE Transactions on Microwave Theory and Techniques
This paper analyzes and demonstrates the use of coupled-LC tanks to enlarge the locking range (LR) of millimeter-wave (mm-wave) subharmonically injection-locked oscillators. Design guidelines are derived from a simplified analysis. Different techniques are proposed to tune the coupled-LC tank. A mm-wave subharmonically injection-locked quadrature voltage-controlled oscillator in 40-nm CMOS verifies the proposed approach. The LR is larger than 2 GHz over a 55-63-GHz tuning range. An on-chip envelope detector facilitates the tuning of the coupled-LC tank. The phase noise and the quadrature-phase imbalance are uniform over almost the whole LR.
24 May 2024 in IEEE Journal of Solid-State Circuits
This article presents a 23-GHz transmitter/low-noise amplifier (TX/LNA) front-end module (FEM) in 130-nm SiGe BiCMOS for inter-satellite links (ISLs) in the system of orbiting low-frequency antenna array (OLFAR). The FEM consists of an LNA, a power amplifier (PA), a variable-gain amplifier (VGA), a phase shifter (PS), and a TX/receiver switch (T/R SW). By applying the combination of different techniques: 1) multi-function block design strategy; 2) current reuse and ${\mathrm { g}}_{\mathrm { m}}$ boosting implemented by a triple-coil transformer in the LNA; 3) dual-LC-tank-based integrated T/R SW, a compact FEM is achieved, simultaneously with an advanced-state-of-the-art efficiency in the TX path and a competitive noise figure (NF) in the receiver (RX) path. In the TX path, it demonstrates a measured saturated output power ( $\mathrm {P}_{\mathrm {sat}}$ ) of 16.8 dBm, a peak TX efficiency of 27.8%, and a 34.1-dB gain. It supports 900-Mbps 64-QAM signals with 4.9% error vector magnitude (EVM) and −27.5-dBc adjacent channel power ratio (ACPR), at 9.0-dBm output power ( $\mathrm {P}_{\mathrm {out}}$ ) with 8.8% TX efficiency. In the RX path, an NF of 3.1 dB and an input 1-dB compression point (IP $_{\mathrm {1~dB}}$ ) of −19.4 dBm are achieved with a 19.3-dB gain and a 10-mW power consumption. The core chip area is $1.11\times 0.48$ mm.
13 December 2016 in Journal of Signal Processing Systems