This paper presents the design and measurement of an interpolation-based low noise and variable gain cell (IBA-cell) in the 60-GHz band, using a 40-nm CMOS technology. The interpolation-based gain cell is designed for an innovative analog beamforming front end, where the array pattern is not only controlled in the phase domain, but also wins the flexibility in the magnitude domain. The circuit specifications are first derived for the application at 60 GHz. Techniques to combine low noise figure (NF) with variable gain tuning are presented focusing on the NF and linearity (IIP₃) on the example of a 60-GHz low noise amplifier and variable gain amplifier. Subsequently, the design and measurement of the whole gain cell (IBA-cell) integrated into a single chip are reported with the technique of a cross-coupled feedback loop to reduce the phase variations over the gain tuning states and enhance the variations of IIP₃. The IBA-cell achieves 15.8-dB maximum gain and 6.5-dB NF at 57 GHz with the gain tuning range from -2 to 15.8 dB and IIP₃ varying from -11.3 to -16 dBm over the gain control range. The IBA-cell consumes a dc power of maximum 54 mA from 1.1 V.
This paper presents a 20 GHz low noise amplifier (LNA) with notch filtering from 27.5 GHz to 31 GHz in a 0.25 μm SiGe:C BiCMOS technology. Notch filters are proposed to be implemented at different stages to have minor impact on the noise figure (NF), while achieving high attenuation around 30 GHz. In comparison with a reference LNA without filtering, it achieves overall filtering of more than -30 dB from 27.5 GHz to 31 GHz, with a NF of 1.9 dB degraded by only 0.1 dB to 0.4 dB. More than 17 dB improvement is achieved on the gain compression and triple beat IIP3 in presence of high power blocker. Besides, both LNA's achieve best NF to-date with high overall performance at K-band in silicon technologies.
The ubiquity foreseen by the Internet-of-Things (IoT) and powered by the 5G advancements has motivated research on wireless solutions for critical applications, in particular, Industrial IoT (IIoT). Nevertheless, there is little or no research on a unified design methodology for IIoT that tackles the conflicting wireless system performances of Power, Latency, and Reliability (PLR). Obtaining such a framework is vital for empowering further development and fair comparison in future IIoT designs. Thereby, this paper presents a novel design methodology to tackle PLR trade-off in IIoT Wireless Systems (IIoT-WS). This new methodology uses a meet-in-the-middle system approach to design an entire PLR RF system, and a custom Multiple-Criteria Decision Analysis (MCDA) to help decide the best design variables that are both resource-efficient and PLR-balanced for a given application. Finally, to quantify the methodology for critical wireless systems, a lab-demonstrator for automotive application is designed and its performance compared to other wireless systems standards.
1 June 2007 in 2007 IEEE Radio Frequency Integrated Circuits (RFIC) Symposium
This paper presents a novel broadband, inductorless, resistive-feedback CMOS LNA. The LNA is designed for the frequency band 0.4 - 1 GHz. The measured power gain of the LNA is 16 dB at 1 GHz and the 3-dB bandwidth is 2 GHz. A noise figure of 3.5 dB and an IIP3 of -17 dBm are measured at 900 MHz. The S11 is better than -10 dB in the frequency band from 300 MHz up to 1 GHz. The current consumption is 14 mA from a 1.2 V supply. The circuit is designed in a baseline CMOS 90 nm low power (LP) process.
5 November 2020 in IEEE Solid-State Circuits Letters
An ultra-low power fully dynamic capacitance-to-digital converter (CDC) that exploits a novel charge reuse technique is proposed. The CDC includes a capacitive bridge as the sensing frontend and an asynchronous SAR ADC for signal digitization. Passive charge sharing between the frontend and ADC is used to enable a fully dynamic operation. Instead of resetting the capacitive bridge (with large sensing and reference capacitors) for each measurement, the charge is maintained and reused over many measurements to save energy. A power gating technique is employed to reduce the stand-by power. As a result, a FoM as low as 4.3fJ/conv-step is achieved for the CDC, which is >3x better than the state-of-the-art. Furthermore, it supports an inherent scaling of power vs. speed with a minimum power of only 44pW and a compact chip area of 6440μm.
24 May 2024 in IEEE Journal of Solid-State Circuits
This article presents a 23-GHz transmitter/low-noise amplifier (TX/LNA) front-end module (FEM) in 130-nm SiGe BiCMOS for inter-satellite links (ISLs) in the system of orbiting low-frequency antenna array (OLFAR). The FEM consists of an LNA, a power amplifier (PA), a variable-gain amplifier (VGA), a phase shifter (PS), and a TX/receiver switch (T/R SW). By applying the combination of different techniques: 1) multi-function block design strategy; 2) current reuse and ${\mathrm { g}}_{\mathrm { m}}$ boosting implemented by a triple-coil transformer in the LNA; 3) dual-LC-tank-based integrated T/R SW, a compact FEM is achieved, simultaneously with an advanced-state-of-the-art efficiency in the TX path and a competitive noise figure (NF) in the receiver (RX) path. In the TX path, it demonstrates a measured saturated output power ( $\mathrm {P}_{\mathrm {sat}}$ ) of 16.8 dBm, a peak TX efficiency of 27.8%, and a 34.1-dB gain. It supports 900-Mbps 64-QAM signals with 4.9% error vector magnitude (EVM) and −27.5-dBc adjacent channel power ratio (ACPR), at 9.0-dBm output power ( $\mathrm {P}_{\mathrm {out}}$ ) with 8.8% TX efficiency. In the RX path, an NF of 3.1 dB and an input 1-dB compression point (IP $_{\mathrm {1~dB}}$ ) of −19.4 dBm are achieved with a 19.3-dB gain and a 10-mW power consumption. The core chip area is $1.11\times 0.48$ mm.