Graphene-based metamaterials are gaining popularity for developing various reconfigurable and electrically tunable optical devices – especially in terahertz (THz) and infrared (IR) bands. Therefore, in this paper, we aim to investigate the broadband metamaterial-based absorber that efficiently absorbs the THz radiation ranging from 2.2 to 4.6 THz. The proposed absorber comprises a simple meta-square ring of graphene, which possesses different slots in its structure to induce multiple plasmonic resonances. It is observed that the proposed absorber manifests above 95% absorption for the normally incident THz waves, and it also maintains its absorption value over 80% for different obliquely incident operating conditions. Furthermore, the proposed absorber shows polarization-insensitive features. In addition, the absorption characteristics regulate from 95% to 15% by adjusting the chemical potential of graphene from 1 eV to 0.1 eV. Some of the salient features of the proposed absorber is largest reported bandwidth for single layer absorber with smallest footprint without sacrificing polarization insensitivity or amplitude tunability. From the application point of view, it could provide the pathway for implementing switching, cloaking, smart absorbers, and detection phenomena in the THz range.
1 December 2020 in IEEE Microwave and Wireless Components Letters
This letter presents an efficient single-cell triband rectifier matched at millimeter-wave frequencies of 24, 28, and 38 GHz using a novel, compact multiband impedance matching network (IMN). The proposed multiband IMN is scalable and is used to design a miniaturized rectifier at the desired frequencies. The actual impedance of rectifier was measured using through-reflect-line (TRL) calibration for accurate design. A prototype of rectifier was realized on Rogers 5880 substrate. The rectifier is capable of harvesting dc output simultaneously from three different millimeter-wave frequency bands including two 5G communication bands and industrial, scientific and medical (ISM) band at 24 GHz. The maximum simulated efficiencies obtained at 24, 28, and 38 GHz are 44.3%, 42.7%, and 43.6% at an input power of about 15.6 dBm and the measured efficiencies are 44%, 41.3%, and 39.7% at an input power of 17.5 dBm, respectively. This rectifier finds its applications as an energy harvester and wireless power transmitter for self-sustainable low-power batteryless systems.
19 December 2024 in IEEE Transactions on Microwave Theory and Techniques
We present a novel, scalable, distributed beamforming receiver array architecture capable of self-synchronization using an analog phase-locked loop (PLL). Wireless frequency synchronization of distributed nodes is achieved at the receiver front-end and at carrier frequency level with extremely low latency, while direct data demodulation is performed at the same time. Compared to existing techniques, frequency synchronization is accomplished without using back-and-forth feedback between the radio nodes within the distributed network. In this work, we demonstrate the wireless beamforming operation through phase alignment of synchronized signals at the output of PLLs. The local oscillator (LO) signal at each receiver is automatically synchronized with the received signal, and the receiver directly down-converts and demodulates the data. Therefore, the need for phase alignment at the carrier frequency translates to the delay adjustment of the demodulated data at an intermediate frequency (IF) for beamforming. A custom-designed receiver at the millimeter-wave frequency band fabricated in GlobalFoundry’s SiGe BiCMOS technology was used for this study. We provide a comprehensive study of distributed beamforming arrays (DBAs) in the presence of interference signals. The emergence of spurious intermodulation (IM) components in the output spectrum of the PLL due to interference signal was observed. We experimentally demonstrate that the coherent combination of signals from different receiving nodes can significantly suppress the interference in distributed arrays once accurate phase alignment of carrier signals is achieved. Additionally, the effects of interference on the phase noise were experimentally studied. A 130-Mb/s data link was established between the transmitter and distributed receiver array by introducing appropriate time delays during the post-processing stages.
This article presents a custom-made SiGe-based transceiver at millimeter-wave frequencies capable of the generation anddetection of radio waves with helical phase distribution called orbital angular momentum (OAM). The proposed architecture isable to suppress the in-band interference at the front-end that otherwise cannot be filtered by front-end filters. The transmitter and receiver chip integrates a front-end power amplifier (PA), phase shifter, low-noise amplifier (LNA), and front-end switches to switch the amplifiers ON and OFF to generate OAM modes. A 4-element transceiver array was constructed using custom-designed chips, mounted on a PCB with a custom-designed circular antenna array. The design generates $l=0$, (+1) and (−1) OAM modes simultaneously, where the mode ($l=0$) is a plane wave mode. Since each mode carries the same information, it is shown that if an interfering signal disrupts the plane wave mode ($l$ = 0), the information can still be recovered from the OAM mode ($l$ = +1), where the interferer is suppressed due to a particular detection method of the OAM wave at the receiver. The experiments show 19 dB interference suppression near the operating frequency of the OAM mode.
10 June 2025 in IEEE Transactions on Microwave Theory and Techniques
This article presents the design, implementation, and experimental evaluation of a custom-designed chip-scale distributed transmit beamforming (DTB) array operating at millimeter-wave frequencies. Each transmitting node incorporates a phase-locked loop (PLL), a phase shifter, and a power amplifier, all fabricated using a 0.13-$\mu \text {m}$ SiGe HBT BiCMOS process. The transmitters are packaged with a custom high-gain patch antenna array to enable millimeter-wave signal transmission. Wireless coherent beamforming was experimentally demonstrated using an array of spatially distributed transmitter nodes synchronized to a common reference signal. The array achieves over 93% of the ideal coherent gain. Solid frequency synchronization was achieved using the on-chip PLLs, resulting in a stable signal with improved phase noise results after beamforming. In addition, a comprehensive analysis of phase noise in DTB arrays is presented and experimentally validated, demonstrating near-theoretical and repeatable phase noise improvements. The impact of frequency synchronization errors and receiver displacement on signal integrity is also investigated, emphasizing the critical role of precise phase and frequency synchronization.
21 April 2025 in IEEE Transactions on Microwave Theory and Techniques
This article introduces a self-identifying relay that can assist in localization by adding unique code to the retransmitted data. The relay has an amplify-and-forward (AF) architecture that provides amplification and phase shift to the received signal and is capable of beamforming if utilized in multiple channels. The relay consists of a low noise amplifier (LNA), a vector modulation-based phase shifter (PS) capable of providing 360° of continuous phase tuning, and two power amplifiers (PAs). The proposed active relay was custom-designed and implemented on a 130-nm SiGe BiCMOS process. The circuit demonstrates a gain of 25 dB, ${P}_{1\,\text {dB}}$ and ${P}_{\text {sat}}$ output power of 8.5 and 12.4 dBm, respectively, at 30 GHz, a 3-dB bandwidth of 5.2 GHz from 27.8 to 33 GHz, and a noise figure (NF) of 5.2 dB at 30 GHz. The proposed relay adds a unique binary phase shift keying (BPSK)-based identification code in the relayed signal by switching two PAs. Based on these codes, the user can be localized by measuring the time difference of arrival (TDoA) of signal coming from different relays.