17 November 2023 in Science
Cooling through solid-state electrocaloric materials is an attractive replacement for vapor compression. Despite recent efforts, devices that are potentially commercially competitive have not been developed. We present an electrocaloric cooler with a maximum temperature span of 20.9 kelvin and a maximum cooling power of 2.1 watts under the moderate applied electric field of 10 volts per micrometer without any observed breakdown. Moreover, the maximum coefficient of performance, even taking into account energy expended on fluid pumping, reaches 54% of Carnot’s efficiency as long as energy is properly recovered. We believe that this demonstration shows electrocaloric cooling to be a very promising alternative to vapor compression cooling.
12 September 2022 in Nature
Coming up with sustainable sources of electricity is one of the grand challenges of this century. The research field of materials for energy harvesting stems from this motivation, including thermoelectrics1, photovoltaics2 and thermophotovoltaics3. Pyroelectric materials, converting temperature periodic variations in electricity, have been considered as sensors4 and energy harvesters5–7, although we lack materials and devices able to harvest in the joule range. Here we develop a macroscopic thermal energy harvester made of 42 g of lead scandium tantalate in the form of multilayer capacitors that produces 11.2 J of electricity per thermodynamic cycle. Each pyroelectric module can generate up to 4.43 J cm−3 of electric energy density per cycle. We also show that two of these modules weighing 0.3 g are sufficient to sustainably supply an autonomous energy harvester embedding microcontrollers and temperature sensors. Finally, we show that for a 10 K temperature span these multilayer capacitors can reach 40% of Carnot efficiency. These performances stem from (1) a ferroelectric phase transition enabling large efficiency, (2) low leakage current preventing losses and (3) high breakdown voltage. These macroscopic, scalable and highly efficient pyroelectric energy harvesters enable the reconsideration of the production of electricity from heat.
12 August 2021 in Advanced Functional Materials
Barocaloric effects in a layered hybrid organic–inorganic compound, (C10H21NH3)2MnCl4, that are reversible and colossal under pressure changes below 0.1 GPa are reported. This barocaloric performance originates in a phase transition characterized by different features: A strong disordering of the organic chains, a very large volume change, a very large sensitivity of the transition temperature to pressure and a small hysteresis. The obtained values are unprecedented among solid‐state cooling materials at such low pressure changes and demonstrate that colossal effects can be obtained in compounds other than plastic crystals. The temperature‐pressure phase diagram displays a triple point indicating enantiotropy at high pressure.
31 July 2020 in Journal of Materials Chemistry A
Giant reversible barocaloric effects at low pressures in a wide temperature span near room temperature in C 60 for solid-state cooling.
7 October 2025 in Nature Communications
The increasing demand for higher operating speeds and greater integration densities in electronic devices has made heat dissipation one of the most critical challenges for next-generation technologies. This challenge has driven extensive efforts aimed at achieving a giant electrocaloric effect in ferroelectrics for high-efficiency cooling. Here, we propose a defect dipole engineering strategy to manipulate the polarization behavior of ferroelectric ceramics, leading to superior electrocaloric effect. By incorporating Sm and Li ions, the (SmBȧ-LiBaʹ) defect dipoles enhance the polarizability of BaTiO3. Simultaneously, these dipole defects increase the carrier activation energy, effectively mitigating the inherent trade-off between high breakdown strength and high polarization, thereby allowing the application of a high electric field to fully activate the electrocaloric potential. As a result, defect dipole engineering enables BaTiO3 to achieve a remarkable electrocaloric effect over a wide temperature range, achieving a high temperature change of 2.7 K at 70 °C— typical for integrated circuits.
13 July 2021 in Physical Review Applied
In materials science, intentional doping has been widely used to improve the properties of a variety of materials. However, such an approach is not yet exploited in the fast-growing field of electrocaloric materials, which represent a serious alternative for next-generation cooling systems. Here we demonstrate with , an ecofriendly ferroelectric material, that doping with 2% of introduces defect dipoles into the ferroelectric matrix and results in (i) enhancement of the adiabatic temperature change ΔT by up to 54% while maintaining performance after a large number (up to ) of electric field cycles, (ii) suppression of the parasitic irreversibility of ΔT between on-field and off-field states, and (iii) an alternative design of refrigeration cycle with a prepoled sample, allowing a two-field-step process showing both conventional (ΔT > 0) and inverse (ΔT < 0) responses when the field is sequentially varied. We also demonstrate that doping significantly increases the energy storage density (by up to 72%). The defect engineering approach therefore offers a path for designing ferroelectrics with improved electrocaloric performances. Beyond ferroelectrics, this strategy could also be promising in other solid-state caloric materials (magnetocalorics, elastocalorics, etc.).