2 April 2021 in IEEE Journal of Microwaves
Synthetic aperture radar (SAR) is a well-known imaging technique and most commonly used up to the microwave frequency spectrum (below 30 GHz) which provides spatial resolution in the sub-m range. To enhance the resolution, higher frequency spectra such as millimeter-wave (mmWave) and terahertz (THz) regions are being investigated. The mmWave and THz spectral ranges extend the SAR applications to non-destructive testing (NDT), material characterization, and sub-mm resolution imaging. However, the higher frequency spectrum suffers from higher path loss and potentially higher atmospheric absorption that limits the propagation distance. Nevertheless, the mmWave/THz spectrum is suitable for short-range applications such as indoor room profiling. From theoretical analysis, it can be summarized that the higher frequency spectrum provides better resolution but a comparative study on the impact on the image quality of the frequency spectrum ranging from GHz to THz has not been presented. Besides, as of the hardware complexity of the THz devices, the optimum range of the spectrum is always under investigation. The optimum range is defined where no strong improvements in the image quality are achievable with further increases in the frequency spectrum. Therefore, this paper presents an overview of electronics-based imaging using the SAR technique for the frequency spectrum ranging from GHz to THz with the focus on NDT and high-resolution imaging. Seven frequency bands: 5-10 GHz, 68-92 GHz, 75-110 GHz, 0.122-0.168 THz, 0.22-0.33 THz, 0.325-0.5 THz, and 0.85-1.1 THz are selected for a comparative analysis. The results are presented for 2D and 3D imaging using the backprojection algorithm. Additionally, state-of-the-art imaging based on SAR technique with electronics transceiver modules has only been demonstrated up to the sub-0.75 THz, whereas in this paper the spectrum up to 1.1 THz has been addressed.
12 August 2019 in IEEE Access
In this paper, we propose a fast terahertz time-domain imaging method using a radar migration algorithm. We demonstrate high-resolution imaging in reflection without any collimating or focusing optics in the terahertz beam. In the proposed method, the sample is illuminated with a divergent terahertz beam, and the receiver collects both specular and diffuse reflections.We further present calibration and post-processing methods that allow us to compensate for the inherently low signal-to-noise ratio of an unfocused terahertz beam. The feasibility of the novel imaging method is demonstrated with geometrically complex samples and a fast terahertz time-domain spectroscopy system based on electronically controlled optical sampling. We show that our concept is capable of generating images of the objects regardless of their size, shape, orientation and position relative to the transmitter and receiver antennas. Objects with edge lengths well below 400 μm can be clearly detected. The method presented here thus lends itself to arbitrary scenarios and antenna configurations.
19 August 2020 in IEEE Access
Imaging in the terahertz frequency range has attracted growing interests since the first image of a leaf more than 20 years ago, due to its countless applications in basic and applied research, medical imaging, and nondestructive testing. However, most terahertz imaging approaches rely on focusing optics which require knowledge about the imaging scene before the actual imaging takes place. Further, imaging is mostly restricted to short distances and high resolution is only achieved for systems with a high bandwidth. Here, we present a method that enables high-resolution imaging of small metallic and dielectric objects at distances up to 2 m based on a synthetic aperture. We derive a simple approximation for the resolution of partial circular synthetic apertures with limited bandwidth. The bandwidth limitation is encountered by replacing the measured signals with replica signals of high bandwidth and equal round-trip time so that the resolution is only limited by the carrier frequency and signal-to-noise ratio of the measurement system.
1 January 2021 in IEEE Access
The potential of pulsed THz radiation for time-of-flight imaging applications is well recognized. However, advances in this field are currently severely limited by the low average power of ultrafast THz sources. Typically, this results in impractically long acquisition times and a loss in resolution and contrast. These limitations make imaging of the objects in real-life scenarios impossible. Here, conclusively, the potential of state-of-the-art high-average power THz time-domain spectrometer (TDS), driven by a 100-W class, one-box ultrafast oscillator for imaging applications is shown by demonstrating lensless THz imaging in reflection mode of a dielectric sample with low reflectivity. Images obtained with our home-built 20-mW average power THz-TDS system show a significant contrast enhancement compared to a state-ofthe-art commercial THz-TDS with less than 200 μW of average power. Our unique setup even allows us to obtain images of such an object with high-contrast hidden inside a medium-density fiberboard (MDF) box. This opens the door to THz time-of-flight imaging of concealed objects of unknown shape and orientation in various real-life scenarios which were so far impossible to realize.
25 January 2023 in IEEE Access
Terahertz time-domain spectroscopy (THz-TDS) is a promising tool for high-resolution 3D imaging of objects due to the high center frequency and bandwidth compared to microwave systems. In addition, terahertz waves have a higher penetration depth than visible or near-infrared radiation. Typically, optics are used to focus the terahertz radiation onto an object under test. This limits the imaging capability in the axial dimension to the depth of field and limits simple imaging of complex surfaces. In this work, we adapt a backpropagation algorithm from synthetic aperture radar (SAR) imaging to reconstruct high-resolution 3D images from time-domain traces acquired with a lensless THz-TDS system. For this purpose, an inverse cylindrical aperture is used and an equation that describes the maximum achievable resolution as a function of the beam pattern, the bandwidth, and the length of the synthetic aperture is derived. The calculated resolution is 960 µm for the linear dimension of the aperture and 75 µm for the rotationally symmetric dimension of the cylindrical aperture for a bandwidth of 2 THz. The resolving power is verified by measurements on metallic and dielectric objects. In the future, this method can be used for non-destructive testing of objects with complex shaped surfaces and internal structures.
7 October 2020 in IEEE Access
Material characterization in the 0.1 _ 10 THz range has been a major topic of research since its first demonstration 30 years ago. Advances in terahertz generation, detection, and data acquisition have contributed to improved bandwidth, signal power and signal-to-noise ratio. However, material characterization is still performed using conventional spectroscopic measurement schemes which require detailed information about the test object’s shape, location, orientation relative to the measurement system, and a reference measurement. Here, we present a method for reference-free material characterization of dielectric objects using a terahertz time-domain spectroscopy system without a priori knowledge about the object and its position. The proposed method is based on ellipsometry combined with lensless imaging for the estimation of the refractive index. The method is a multistage procedure designed for small test objects in reflection mode. The diffracted terahertz radiation is separated from the specular reflected radiation in a post-processing step to enable a valid material parameter estimation. In this way, small dielectric objects can be located, imaged with a sub-mm resolution, and their material parameters extracted.