Electronic Engineering Department, Universitat Politècnica de Catalunya (UPC), Photovoltaic Lab – Micro and Nano Technologies Group (MNT), EEBE, Av, Eduard Maristany 10-14, Barcelona 08019, Catalonia, Spain
Auto-generated profile, based on publicly available information
Zacharie Jehl Li-Kao
Electronic Engineering Department, Universitat Politècnica de Catalunya (UPC), Photovoltaic Lab – Micro and Nano Technologies Group (MNT), EEBE, Av, Eduard Maristany 10-14, Barcelona 08019, Catalonia, Spain
Sb2Se3 is a quasi-one-dimensional (1D) semiconductor, which has shown great promise in photovoltaics. However, its performance is currently limited by a high Voc deficit. Therefore, it is necessary to explore new strategies to minimize the formation of intrinsic defects and thus unlock the absorber’s whole potential. It has been reported that tuning the Se/Sb relative content could enable a selective control of the defects. Furthermore, recent experimental evidence has shown that moderate Se excess enhances the photovoltaic performance; however, it is not yet clear whether this excess has been incorporated into the structure. In this work, a series of Sb2Se3 thin films have been prepared imposing different nominal compositions (from Sb-rich to Se-rich) and then have been thoroughly characterized using compositional, structural, and optical analysis techniques. Hence, it is shown that Sb2Se3 does not allow an extended range of nonstoichiometric conditions. Instead, any Sb or Se excesses are compensated in the form of secondary phases. Also, a correlation has been found between operating under Se-rich conditions and an improvement in the crystalline orientation, which is likely related to the formation of a MoSe2 phase in the back interface. Finally, this study shows new utilities of Raman, X-ray diffraction, and photothermal deflection spectroscopy combination techniques to examine the structural properties of Sb2Se3, especially how well-oriented the material is.
The lack of a systematic definition of intermittency in the power sector blurs the use of this term in the public debate: the same power source can be described as stable or intermittent, depending on the standpoint of the authors. This work tackles a quantitative definition of intermittency adapted to the power sector, linked to the nature of the source, and not to the current state of the energy mix or the production predictive capacity. A quantitative indicator is devised, discussed and graphically depicted. A case study is illustrated by the analysis of the 2018 production data in France and then developed further to evaluate the impact of two methods often considered to reduce intermittency: aggregation and complementarity between wind and solar productions.
3 January 2022 in ACS Applied Materials & Interfaces
Accurate anionic control during the formation of chalcogenide solid solutions is fundamental for tuning the physicochemical properties of this class of materials. Compositional grading is the key aspect of band gap engineering and is especially valuable at the device interfaces for an optimum band alignment, for controlling interface defects and recombination and for optimizing the formation of carrier-selective contacts. However, a simple and reliable technique that allows standardizing anionic compositional profiles is currently missing for kesterites and the feasibility of achieving a compositional gradient remains a challenging task. This work aims at addressing these issues by a simple and innovative technique. It basically consists of first preparing a pure sulfide absorber with a specific thickness followed by the synthesis of a pure selenide part of complementary thickness on top of it. Specifically, the technique is applied to the synthesis of Cu2ZnSn(S,Se)4 and Cu2ZnGe(S,Se)4 kesterite absorbers, and a series of characterizations are performed to understand the anionic redistribution within the absorbers. For identical processing conditions, different Se incorporation dynamics is identified for Sn- and Ge-based kesterites, leading to a homogeneous or graded composition in depth. It is first demonstrated that for Sn-based kesterite the anionic composition can be perfectly controlled through the thicknesses ratio of the sulfide and selenide absorber parts. Then, it is demonstrated that for Ge-based kesterite an anionic (Se–S) gradient is obtained and that by adjusting the processing conditions the composition at the back side can be finely tuned. This technique represents an innovative approach that will help to improve the compositional reproducibility and determine a band gap grading strategy pathway for kesterites. Furthermore, due to its simplicity and reliability, the proposed methodology could be extended to other chalcogenide materials.
30 November 2022 in Solar Energy Materials and Solar Cells