16 March 2018 in Scientific Reports
Absolute measurements of the radiolytic yield of Fe3+ in a ferrous sulphate dosimeter formulation (6 mM Fe2+), with a 20 keV x-ray monoenergetic beam, are reported. Dose-rate suppression of the radiolytic yield was observed at dose rates lower than and different in nature to those previously reported with x-rays. We present evidence that this effect is most likely to be due to recombination of free radicals radiolytically produced from water. The method used to make these measurements is also new and it provides radiolytic yields which are directly traceable to the SI standards system. The data presented provides new and exacting tests of radiation chemistry codes.
26 March 2014 in Optics Express
Diamond possesses many extreme properties that make it an ideal material for fabricating nanofocusing x-ray optics. Refractive lenses made from diamond are able to focus x-ray radiation with high efficiency but without compromising the brilliance of the beam. Electron-beam lithography and deep reactive-ion etching of silicon substrates have been used in a transfer-molding technique to fabricate diamond optics with vertical and smooth sidewalls. Latest generation compound refractive lenses have seen an improvement in the quality and uniformity of the optical structures, resulting in an increase in their focusing ability. Synchrotron beamline tests of two recent lens arrays, corresponding to two different diamond morphologies, are described. Focal line-widths down to 210 nm, using a nanocrystalline diamond lens array and a beam energy of E = 11 keV, and 230 nm, using a microcrystalline diamond lens at E = 15 keV, have been measured using the Diamond Light Source Ltd. B16 beamline. This focusing prowess is combined with relatively high transmission through the lenses compared with silicon refractive designs and other diffractive optics.
8 March 2021 in Applied Physics Letters
Ptychography is a scanning coherent diffraction imaging technique that provides high-resolution imaging and complete spatial information of the complex probe and object transmission function. The wavefront error caused by aberrated optics has previously been recovered using ptychography when a highly coherent source is used, but has not been demonstrated with partial coherence due to the multi-modal probe required. Here, we demonstrate that partial coherence can be accounted for in ptychographic reconstructions using the multi-modal approach and assuming that decoherence arises from either the probe or the object. This equivalence recovers coherent (or single state) reconstructions of both the probe and the object even in the presence of partial coherence. We demonstrate this experimentally by using hard x-ray ptychography with a partially coherent source to image a Siemens star test object and to also recover the wavefront error from an aberrated beryllium compound refractive lens. The source properties and resolving capabilities are analyzed, and the wavefront error results are compared with another at-wavelength metrology technique. Our work demonstrates the capability of ptychography to provide high-resolution imaging and optics characterization even in the presence of partial coherence.
16 October 2020 in Journal of Synchrotron Radiation
Ptychography is a scanning coherent diffraction imaging technique which provides high resolution imaging and complete spatial information of the complex electric field probe and sample transmission function. Its ability to accurately determine the illumination probe has led to its use at modern synchrotrons and free-electron lasers as a wavefront-sensing technique for optics alignment, monitoring and correction. Recent developments in the ptychography reconstruction process now incorporate a modal decomposition of the illuminating probe and relax the restriction of using sources with high spatial coherence. In this article a practical implementation of hard X-ray ptychography from a partially coherent X-ray source with a large number of modes is demonstrated experimentally. A strongly diffracting Siemens star test sample is imaged using the focused beam produced by either a Fresnel zone plate or beryllium compound refractive lens. The recovered probe from each optic is back propagated in order to plot the beam caustic and determine the precise focal size and position. The power distribution of the reconstructed probe modes also allows the quantification of the beams coherence and is compared with the values predicted by a Gaussian–Schell model and the optics exit intensity.
1 February 2019 in Review of Scientific Instruments
X-ray mirrors are widely used in beamlines and laboratories as focusing or collimating optics. As well as the highly accurate processes used to fabricate them, optimized alignment of X-ray mirrors also plays an important role in achieving an ideal X-ray beam. Currently, knife-edge scans are the most often used method for aligning X-ray mirrors, which can characterize the focal size and tune the alignment iteratively. However, knife-edge scanning provides only one-dimensional information and this method suffers from being time-consuming and requiring a high-resolution piezo translation stage. Here we describe a straightforward and non-iterative method for mirror alignment by measuring the relationship between the tilt aberration and the misaligned pitch angle, which is retrieved by an at-wavelength metrology technique using a randomly shaped wavefront modulator. Software and a graphical user interface have been developed to automate the alignment process. Combining the user-friendly interface and the flexibility of the at-wavelength metrology technique, we believe the proposed method and software can benefit researchers working at synchrotron facilities and on laboratory sources.
31 July 2023 in Nature Communications
Visible light optical elements such as lenses and mirrors have counterparts for X-rays. In the visible regime, a variable focusing power can be achieved by an Alvarez lens which consists of a pair of inline planar refractors with a cubic thickness profile. When the two refractors are laterally displaced in opposite directions, the parabolic component of the wavefront is changed resulting in a longitudinal displacement of the focus. This paper reports an implementation of this concept for X-rays using two planar microfabricated refractive elements. The Alvarez X-ray lens can vary the focal distance of an elliptical X-ray mirror or a planar compound X-ray lens over several millimetres. The study presents the first demonstration of an Alvarez X-ray lens which adaptively corrects defocus and astigmatism aberrations of X-ray optics. In addition, the Alvarez X-ray lens eliminates coma aberration in an elliptical mirror, to the lowest order, when combining the lens with an adjustment of the pitch angle of the mirror.